易熔點 的英文怎麼說
中文拼音 [yìróngdiǎn]
易熔點
英文
eutectic point-
Dark red flake, melting point 197 ` c, easily deliquescent, soluble in water poisonous, corrosive and flammable with the organic
呈紅色片狀物,熔點197 ` c ,極易溶解,易溶於水,有毒,腐蝕性強,與有機物接觸可引起燃燒。But there are some technical difficults for the welding of aluminium alloy such as some broken bits being easily found, a large welding distortion can happen easily, hard to distinguish the difference between the solid metal and liquid metal colour, hard to control the temperature, a lot of air holes can be seen in the welding line and so on
但是鋁合金熔化焊時的技術難點在於:焊接時易引起夾渣,焊接變形大,金屬的固態和液態的色澤不容易區別,焊接操作時控制溫度困難,容易產生氣孔等等。如果焊前清理工作不是很好,檢測氣孔往往超標。If coreless melting furnace mainly for steel , alloy steel , cast iron , and other ferrous metal materials and stainless steel , copper , aluminum , zinc and other non - ferrous metal materials melting , melting with high efficiency , energy - saving , metal components uniform , burning less temperature or block , simple operation , easy to supporting the advantages of production lines
中頻無芯熔煉爐主要用於鋼、合金鋼、鑄鐵等黑色金屬材料以及不銹鋼、銅、鋁、鋅等有色金屬材料的熔煉,具有融化效率高、節電、金屬成分均勻、燒損少、溫升塊、操作簡單、易於配套生產線等優點。But some problems are occurred, such as low bath temperature, difficulty in lime melting, slag overflow at vessel mouth, increase of metal consumption, difficulty in dephosphorization and low hitting rate at the final
在生產中出現熔池溫度低、廢鋼和石灰不易熔化、爐口溢渣、金屬消耗增加、脫磷困難、終點命中率低等問題。Mainly made of super - fine three - dimensional staple fibers and mixed with some polyester staples of low melting point and finished products scarcely containing glue materials. after being calenderized and ironed, the product get smooth surface, silk - like glittering effect, light and exquisite hand feeling, softness, heat preservation, good washing endurance, no distortion and leaking. it feels like down but with fine tenacity and is the best among all spray bond padding products
用超細三維中空短纖維為主要原料,配以部分低熔點滌綸短纖,成品含膠量極少,經過軋光燙平后,仿絲綿表面平整、有絲光、輕薄、手感細膩、柔軟、保溫好、耐水洗性極強、不易變形、不會跑毛、手感似羽絨,具有質地纖細、表面如蠶絲、有拉力、柔軟等特點,是噴膠棉中最高擋的產品。There are kinds of polycarbonate ( pc ), it is worth a kind of engineering materials for bisphenol a - polycarbonate, its main shortcoming are crazed easily, high molten body viscidity and difficult forming process characteristic, so many kinds of modified methods are brought into effect for it
摘要聚碳酸酯品種較多,作為工程材料最有價值的是雙酚a型聚碳酸酯,其主要缺點是易開裂,熔體粘度高,成型加工較困難,為此進行了各種改性方法。The heating speed is quick, the loss is less, controlling the chemical composition is easy, the quality of the product or is high, the chimney is less and the operation is convenient
本公司生產的中頻感應熔爐,具有加熱速度快,金屬損耗小,化學成分容易控制,產品質量高,煙塵小,便於操作等優點。But most of the researches focus on the reaction of single oxide and al to form wild phase al2o3. these researches show that only cuo / al reaction system can produce al2o3 particles steadily. however, the reaction is very drastic and it belongs to blast reaction
但大部分的研究集中在單一氧化物與al的置換反應生成增強顆粒al _ 2o _ 3的方法上,研究表明,只有cuo al反應體系在al熔點以上不高的溫度范圍能穩定生成顆粒,但同時cuo al反應過于劇烈,屬于燃爆反應,不易控制。The liquid crystalline field of the polymers could be well kept at room temperature and the initial decomposition temperature of all the polymers was higher than the clearing point
所有聚合物的熔點都非常低,表明合成的一系列液晶聚合物非常容易進入液晶態,並且液晶場能夠很好地保存到室溫。Magnesium - base alloys are easy to catch fire when heated at high temperature or melten, and this has become an obstacle to the developing of magnesium - base alloys. so, whether magnesium - base alloy can be used widely depends on the progress of the developing of the flame - resistant technique of magnesium - base alloys
鎂合金在高溫下、尤其是在熔煉時很容易起火燃燒,這一缺點嚴重阻礙了鎂合金的發展,所以鎂合金的阻燃技術是關繫到鎂合金能否得到廣泛應用的關鍵所在。The melting sticking occurred when the melting point of materials is lower than the drying temperature
物料熔點低於乾燥溫度時容易產生熱熔性粘壁。分享友人