晶圓對準 的英文怎麼說

中文拼音 [jīngyuánduìzhǔn]
晶圓對準 英文
wafer alignment
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 晶圓 : mpw
  1. This paper describes briefly the measurement of equipment efficiency and equipment capacity and introduces mainly its applications in semiconductor wafer manufactory

    本文針對該問題，系統地介紹了半導體晶圓製造中設備效率和設備能力的衡量標準及其數據收集，以期達到提高設備利用率的目的。
  2. X - ray full wafer aligner x

    線整片晶圓對準曝光器
  3. Wafer rotation error

    晶圓對準旋轉誤差
  4. When your dual sim card used for a long time, please use the ball pen to touch the 12 small metal dots in order to make them connect better

    雙卡使用較久時，用圓珠筆筆頭部分對準雙卡晶片上的12個小突點轉一轉，增加其突點高度，讓卡片與雙卡接觸更好
  5. Sometimes sim card can not connect well with mobile phones that the space of card holder is a little bigger, maybe it will cause the mobile reboot, try to stick adhesive tape on the dual sim card to make it more tightly

    雙卡使用較久時，用圓珠筆筆頭部分對準雙卡晶片上的12個小突點轉一轉，增加其突點高度，讓卡片與雙卡接觸更好
  6. The main content of the research is to design and manufacture a system that is fit for 12 - inch wafer pre - aligning

    主要研究內容是研製用於12英寸晶圓預對準的系統。
  7. The wafer processing system is an important subsystem of the lithography, which consists of a wafer transmission system and a wafer pre - alignment system

    晶圓處理系統是光刻機的重要組成子系統，其包含兩個主要部分:晶圓傳輸系統和晶圓預對準系統。
  8. In the function decision and structure design, the function and the flow of the wafer pre - alignment system are analyzed, the system architecture is selected and the precision of this system is analyzed, the driving mode and the system structure are fixed, and then the motor and raster are selected. at the same time, the structure of parts is designed on consideration of the request and the function of the vacuum grasping of wafer

    在總體方案和機構設計方面，分析了晶圓預對準系統的功能與流程，選定了系統的整體方案，確定了系統各單元的驅動方式和機構形式，完成了驅動和檢測部分的選型，同時充分考慮機構中氣動吸附部分的功能與要求，設計了預對準單元的機構。
  9. Finally, the paper analyses and discusses the collectivity design, the optics system design ( dispersion system, imaging system and the recording system ) and the typical mechanism design. then, it presents the total assemble graph of the spectrometer and the projects for aiming and alignment of tcecs. especially, twin channels are utilized

    最後，論文從雙通道橢圓彎晶譜儀的總體設計、光學系統（包括色散系統、成像系統、接收記錄系統）的設計和典型機械結構的設計等方面對整個譜儀的結構設計都加以了分析和討論，並給出了整個譜儀的總體裝配圖和瞄準對中方案。
分享友人
分享到 Line

分享到臉書