晶軸模型 的英文怎麼說

中文拼音 [jīngzhóumóxíng]
晶軸模型 英文
model of crystal
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 模型 : 1 （仿製實物） model; pattern 2 （制砂型的工具） mould; pattern3 （模子） model set; mould patter...
  1. Moke and fmr studies were performed on single crystalline fe ultathin films epitaxially grown on iii - v semiconductor gaas substrate with thickness 4. 1 - 33 monolayer ( ml ). a theoretical mode for fitting fmr experimental data was established. the results demonstrated the structures and reproduced the evolution of the magnetic properties of ultrathin films with various thickness from the state of superparamagnetic nano - cluster through coexistence of two magnetic phases to continuous film, especially the change of magnetic crystalline anisotropy from unixial to cubic

    1 - 33原子層厚度（ monolayer ，簡稱ml ）的fe單晶超薄膜進行了鐵磁共振（ fmr ）和磁光研究，建立了理論模型對鐵磁共振實驗結果進行了模擬，重現了不同厚度的超薄膜，從納米團簇到兩相共存的過度階段直至連續薄膜結構與磁性的變化，特別是磁各向異性從單軸各向異性向立方各向異性轉變的演化過程。
  2. Not only general suitability of this method is independent of gratings model, geometry structure, medium properly and crystal axis orientation ( including uniaxial crystals and biaxial ones ), but also physical concepts are clear and formula is concise

    該方法不僅不受光柵模型、幾何結構、介質性質和晶體取向（包括單軸和雙軸晶體）的影響而具有普遍適用性，而且其物理概念清晰、公式簡潔。
  3. This thesis was divided into eight chapters, and the main results and innovations obtained here can be summarized as follows : ( 1 ) the physics model of tsrs in frequency conversion crystals has been built up firstly. based on quantum - mechanical viewpoints and the following physical processes and parameters : the two - photo interaction of light with matter, paraxial diffraction of stokes, langevin noise sources, reflection at the faces and the edges of crystals, gain coefficient, beam aperture, pulse width and fluence of 3, the physics model of tsrs in kdp and kdp crystals acting as high - fluence frequency convector and the paraxial operator maxwell - bloch - langevin equations have been built up

    全文共分八章，取得的主要成果及創新點如下： （ 1 ）首次建立了諧波轉換晶體的tsrs物理模型本文根據量子力學原理，在考慮如下物理過程和參量的基礎上：光與物質的雙光子相互作用； stokes光的傍軸衍射； langevin （郎茲萬）噪聲源；晶體表面反射和端面反射；增益系數、光束口徑、脈寬和三倍頻光能量密度，推導出高通量激光在kdp和kd ~ * p諧波轉換晶體中的tsrs物理模型和空間上的近軸算符maxwell - bloch - langevin方程組。
  4. Sem, transmission electron microscopy ( tem ), x - ray energy - dispersion analysis ( edax ), xrd, electron diffraction ( ed ) and high - resolution electron microscopy ( hrem ) were used to investigate the morphology, atomic composition and crystal structure of the nanowires. the hexagonal cdse nanowires with single crystal structure have been obtained in dmso under 140. ( 3 ) semiconductor te and cdte nanowires embedded in aao templates were fabricated for the first time by dc < wp = 7 > electrodeposition in ethylene glycol

    Sem 、 tem 、 edax 、 xrd 、 ed 、 hrem分析的結果表明，所得cdse納米線為六方晶型，晶體的（ 001 ）晶面沿平行於基底的方向擇優生長，且隨沉積溫度的降低，這種擇優生長的趨勢越來越強；納米線晶體在生長時，由於受aao模板孔徑的限制，形成c軸方向拉長的晶粒，其長徑比達5 1以上；晶體的大小和完善程度隨沉積溫度的降低而增大， 185沉積得到多晶六方cdse納米線，而140沉積時可得到六方cdse單晶納米線。
  5. A uniaxial hot - pressing test and a physical modeling simulation are performed to investigate the orientational alignment of crystals, and a new attempt to strengthen mica glass - ceramics is made

    摘要利用單軸熱壓變形物理模型進行實驗類比，對強化雲母微晶玻璃的新途徑晶體定向排列進行了研究。
  6. Keywords : micro - gyroscope, silicon single crystal, three - axis angular - rate sensing, natural frequency and mode shapes

    關鍵詞：微型陀螺儀、矽單晶、三軸角速率感測、振動自然頻率與模態。
  7. The catena product wholly design for transporting definite corrosive medium have granule or crystal, adopt steel pad uhmw - pe to made it. owned excellent resist causticity and reputably resist attrition, structure and design is model of hang arm front - karat, impeller is half karat model no front cover, boost up transit capability of passage. let the granule and impurity of medium pass pump - cavity quickly not to jam

    本系列產品專為輸送具有一定腐蝕性且含有細顆粒或有結晶的介質而設計，採用鋼襯超高分子量聚乙稀模壓成型工藝製造，具有優異的耐腐蝕性和卓越的耐磨性能，結構設計為懸臂前開式，葉輪為半開式無前蓋板，增強了流道內的通過性，使介質中的顆粒及雜質很快通過泵腔而不會堵塞，軸封為k型氟橡膠密封環外帶冷卻水套，兼顧了耐腐與耐磨的雙重要求。
分享友人
分享到 Line

分享到臉書