曲線磨床 的英文怎麼說

中文拼音 [qūxiànmóchuáng]
曲線磨床 英文
contour grinder
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 床 : i 名1 （供人睡覺的傢具） bed; couch 2 （像床的器具、地面） something shaped like a bed Ⅱ量詞（用...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. Abstract : the design, manufacturing and measurement method of cam profiling are discussed in this paper by describing cam shaft grinding, fabrication of cam profiling, formation of contour of cam profiling, method of compensative fabrication of cam profiling, and measurement and evaluation of cam profiling

    文摘:從凸輪軸磨床磨削工件凸輪、反靠凸輪靠模的過程，凸輪靠模輪廓曲線的形成，補償反靠凸輪靠模的方法，標準凸輪軸的刮削及補償量的確定，凸輪靠模的檢測與評定等，論述了凸輪靠模的設計、製造與檢測方法。
  2. Some testing devices are of advanced ones, such as scanning electronic microscope, microfocus circular radioscope, water - immersed ultrasonic flaw detector, 3 - axis measuring machines, large - sized projector, etc. for the production of non - aero products, there are large - sized die - casting equipment, and nearly 100 pieces of specialized gear machine tools including worm - gear grinding machine, etc. it has some specialized production lines for piston, crankshaft, cylinder and housing, etc., as well as 4 flexible production lines advanced at home for motorcycle engine, and a complete set of automatic inspection test eqiuipment for motorcycle engine

    計算機輔助設計輔助加工技術正在普遍使用。在非航空產品生產方面有大型壓鑄設備殼型鑄造，包括鍋桿輪磨在內的輪專用機床100多臺，以及活塞曲軸汽缸殼體等專業化生產線。此外，還建成了具有國內領先水平的4條摩托車發動機柔性生產線，以及成套的摩托車發動機檢測設備，可進行測試數據分析，改進檢定測試方法等。
  3. Which include cutting - edge curves, rake & flank face, edge angle, tool paths of enveloping rake & flank face, post processing technique of coordinate transfer, design - analyse and simulation sofeware. the research would offer sufficient academic basics and direction about manufacturing of ball - end cutters on the existing nc grinder

    其中包括了球頭立銑刀的刃口曲線模型，前、后刀面模型，刀具角度分析，砂輪磨削前、后刀面的刀位軌跡模型，刀位軌跡與機床坐標轉換的後置處理，球頭立銑刀的設計與模擬軟體的開發。
  4. Optical projection profile grinding machines - parameters

    光學曲線磨床參數
  5. Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied

    然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。
  6. The cross short rollers guide way and servo feed - system are the most important parts of 3mz204cnc bearing internal grinding machine made by luoyany bearing research institute. - we have analysised firstly the factor of influence with roller guide way rigid, and we have obtained a load - distortion curve. we also have analysised the dominating factors influence with distinguish ratio of guide way, and we have obtained a solution about pre - tighted load which were tested by experiments

    本文對洛陽軸承研究所研製的3mz204cnc全自動內圓磨床的核心部件：十字交叉滾子導軌和數控進給系統展開研究，首先對影響滾動導軌剛度的因素進行分析，得出載荷?變形曲線，對影響導軌解析度的各因素進行分析，得出預緊力大小與分佈對解析度和起動力的影響，並通過實驗驗證。
  7. Iges and step standard format and the sat format which is used in acis has been studied. according to the characters of different parts and the characters of different machine tools, a method of grinding for non - circular surface is researched, a new strategy and algorithm of non - circluar surface nc griding which based on acis is studied. a way of non - circluar surface internal grinding is realized as well as the way of non - circluar surface external grinding

    論文的研究包括了以下幾個方面:研究了三維幾何造型引擎acis平臺及其拓撲結構，探討了iges和step等產品數據交換標準格式和acis中的sat文件格式的異同;根據零件的加工特徵和機床的結構特點，研究了在內圓磨削和外圓磨削方式下，非圓曲面磨削的數控編程技術;提出了基於acis實體造型的任意非圓曲面零件的數控磨削新演算法;實現了以實體造型為基礎的任意非圓曲面零件的內圓和外圓數控磨削;根據零件的特徵和磨削方式，生成了相應的走刀路線;實現了針對不同機床的後置處理。
分享友人
分享到 Line

分享到臉書