替換控制器的英文怎麼說

中文拼音 [huànkòngzhì]
替換控制器英文
replace controller

  • : Ⅰ動詞1 (代替) replace; substitute for; supply [take] the place of 2 [書面語] (衰敗) decline Ⅱ...
  • : 動詞1. (給人東西同時從他那裡取得別的東西) exchange; barter; trade 2. (變換; 更換) change 3. (兌換) exchange; cash
  • : 動詞1 (告發;控告) accuse; charge 2 (控制) control; dominate 3 (使容器口兒朝下 讓裏面的液體慢...
  • : Ⅰ動詞1 (製造) make; manufacture 2 (擬訂; 規定) draw up; establish 3 (用強力約束; 限定; 管束...
  • : 名詞1. (器具) implement; utensil; ware 2. (器官) organ 3. (度量; 才能) capacity; talent 4. (姓氏) a surname
  • 控制器: controller; regulator; monitor; pilot; keyer; manipulator; control unit; control device; [自動化]...
  • 控制: control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...

※中文詞彙替換控制器在字典百科國語字典中的解釋。

  1. Engine load simulated control system was consisted of two unattached parts of work resistance simulated control subsystem and electric bow wave dynamometer control subsystem. with the mathematic models of engine load simulation controller, which transferred the work resistance ' s change to engine load change immediately, the system can met the need of the simulation control system

    發動機負荷模擬加載系統包括彼此獨立的作業阻力模擬子系統和電渦流測功機子系統兩部分,應用發動機負荷模擬數學模型,使作業阻力的變化及時轉為發動機負荷的變化,能夠滿足模擬系統的要求。
  2. Secondly, it describes the hardware system of the exoskeleton hand, including the circuit design of the driver, the fpga - based motion controller, the processing and the a / d conversion for the sensor signal

    其次,設計了外骨骼手底層系統的硬體電路,包括微型驅動模塊電路的設計,基於fpga的運動電路的設計,傳感信號調理以及模/數轉電路的設計。
  3. Electric - controller is nubbin in developping. we are based on designing to structure of circuit, we are dead against in time and stabilization for controlling and communications, precision and rapidity for transformation etc. we have completed to select on microprocessor, clock - frequency and a / d transfer. it carry out transformation for valve position signal, and select on solid - switch ac

    的電路結構設計的基礎上,考慮到通訊、的及時、穩定、轉的精度和速度等幾方面,主要完成對微處理的選擇、時鐘頻率和a d轉的選用,閥位變送功能的實現,固態交流開關和顯示的選擇等。
  4. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中,本文完成了片外存儲擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示、鍵盤、遠程、模擬、復位、邏輯電平轉、 dsp工作電源校正電路和ac - dc電源等模塊設計以及前面板、後面板等的空間布局設計。其中dsp與除外部存儲的外圍設備之間的數據傳送全部採用串口通信,同時系統電路配置成中斷響應方式,這樣既滿足了系統要求,又充分利用了tms320f2812的硬體資源。在軟體設計中,本文完成了人機界面功能模塊、遠程模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的演算法的程序設計。
  5. Replacing controls in a login control template

    在登錄項模板中
分享友人