最佳噴霧 的英文怎麼說
中文拼音 [zuìjiāpēnwù]
最佳噴霧
英文
best possible spraying-
A nifty spray - on solution could make all the difference for men plagued with problem of climaxing too soon, as the product makes its final thrust in clinical development
一種極佳的液體噴霧劑已進入臨床研究的最後沖刺階段，這對于那些飽受性高潮來得太快的男士來說意義非凡。Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors
諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3Thermal fogging is very susceptible to wind and thermal air currents. if applied during unfavorable conditions, such as during a hot day, the fog may be carried up and over the target places and the application will become ineffective
熱噴霧最易受風和熱氣流影響。如在條件欠佳的情況下（如在炎熱的日間）施放，噴霧可能受熱氣流影響，飄升到蚊子活動范圍的上方而變得無效。The conclusions are drawn as following : 1. regularity of fabrication in aluminum matrix composite ring - shaped performs with large dimensions and effects of parameters were investigated, based on the novel crucible movable spray deposition technology and equipment. the optimal parameters are that the diameter of the delivery tube is 3. 8mm, spray gas pressure is 0. 8mpa, spray height is 200mm, and transferring pressure of sic is 0. 5mpa
通過系統的實驗研究得到如下結論: 1 .基於新型的移動坩堝自動化控制噴射沉積環坯制備技術及裝置，研究了大尺寸鋁基復合材料環坯的制備規律，討論了噴射沉積工藝參數對沉積坯形成過程的影響，得到了最佳工藝參數:導流管直徑d = 3 . 8mm ，霧化氣體壓力p = 0 . 8mpa ，噴射高度h = 200mm ， sic顆粒輸送壓力p送= 0 . 5mpa 。Nxt spray wax can be used with all meguiar ' s waxes, but chemically works best with nxt spray wax
它可適用於各種車蠟，但化學類的與nxt噴霧蠟結合使用，效果最佳。The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm, spray angle is 30 ? the scanning velocity of atomizer is 30mm / s, the original offset of the substrate is 30mm, rotation velocity of the substrate is 120rpm, spray gas pressure is l. ompa, the diameter of the delivery tube is 3. 6mm, the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray
通過對多層噴射沉積原理及工藝參數的研究，得出制備al - 22si - 3cu - 1mg合金的最佳工藝參數為：噴射高度為220mm - 230mm ，基底轉速為120rpm ，霧化器掃描速度為30mm / s ，基底下降轉速依據噴射情況由智能控制器進行實時調整，噴射角度為30 ，初始偏心距為30mm ，導流管直徑為3 . 6mm ，霧化氣壓為1 . 0mpa 。Abstract : in this paper, based on the quadratic general rotary unitized design, the experiments effected by multiple factors have been made on vibro - fluidized bed spray granulation. mathematical model has been established, and the optimum operating parameters are found out
文摘:研究了利用二次通用旋轉組合設計來進行多因素影響的振動流化床噴霧造粒試驗，建立數學模型，得出了具有一定參考價值的最佳操作參數。分享友人