最大吸氣流 的英文怎麼說

中文拼音 [zuìdàxīqìliú]
最大吸氣流 英文
maximal inspiratory flow
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 吸 : 動詞1 （把液體、氣體等引入體內） inhale; breathe in; draw 2 （吸收） absorb; suck up 3 （吸引） a...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 氣流 : 1 [氣象學] air current; airflow; wind current; airstream2 [語言學] breath氣流紡紗 open end spinni...
  1. We make the best use of foreign advanced technology to meet the requirements of different units and the demand of users to its limit. for instance, turbo - sorp technique, wet limestone - gypsum fgd, sda, scr flue gas denitration technique

    例如：環湍流吸收turbo - sorp技術濕式石灰石石膏法煙氣脫硫技術霧乾燥法sda選擇性催化還原scr煙氣脫硝技術等，最大限度地滿足了不同機組不同用戶的需要。
  2. As we know, inverse techniques make blade ' s profile well compatible with its surface velocity distribution, however, they give designers big challenges that the ideal velocity distribution is hard to obtained and sometimes the non - physical solution, such as double covering of flow field or unclosed profiles, would come out. the proposed design procedure in the paper has avoided the disadvantage mentioned above. in this paper, a quasi - irrotational equation is used to describe the flow in cascade instead of the generally used irrotational equation

    眾所周知，一般的反問題和混合問題的最大特點，是在給定的壓力面和吸力面上的壓力分佈或速度分佈條件下，直接得到葉片的幾何形狀，它可以使葉型型面與表面氣流參數有機結起來；其不足之處在於，對設計者而言，很難給定理想的葉片表面壓力分佈或速度分佈，並且有時會得到一個非物理解，如：得出的初始葉型可能會出現前緣、尾緣不封閉的現象。
  3. The most obvious characteristics of the adsorption method is its cost - effective to completely remove selected pollutants from flue gas until the absorbent is saturated. hence, this method can be effectively controlled and is commonly applied air pollution control equipment

    吸附法之最大特點，系能在符合經濟條件之操作范圍內，幾乎完全除去氣流中之某種成份，直至吸附劑容量到達飽和為止，故其控制效率極佳，為十分普遍之氣態污染物控制設備。
  4. In addition, radiation absorption coefficient had a remarkable effect on maximum combustion temperature and maximum wall heat flux in the new phosphoric acid tower

    輻射吸收系數對最高燃燒溫度和壁面最大熱流影響很大，隨輻射吸收系數的增大，最高燃燒溫度和煙氣出口溫度會下降，而壁面最大熱流和平均熱流會上升。
  5. The effects of parameters on maximum combustion temperature, smog exit temperature, maximum wall heat flux, averaged wall heat flux of a new phosphoric acid tower with circular water wall were discussed, including phosphorus consumption, excess - air coefficient, wall temperature and radiation absorption coefficient, with the mathematical model developed in part

    摘要利用已建立的數學模型考察了燃磷量、過剩空氣系數、壁面溫度、輻射吸收系數對新型燃磷塔的最高燃燒溫度、煙氣排放溫度、壁面最大熱流和平均熱流的影響。
  6. Airway resistance ( raw ) tends to increase and inspiratory resistance ( ri ) in 7d increases significantly. compliance of lung ( cl ) has not a prominent change. 2. the alveolocapillary permeability increases during simulated weightlessness and can recover a bit as simulated weightlessness goes on

    3秒率oevm x呼氣峰流速oef卜最大通氣量p ）比正常水平降低，其中以7dfevm和zidmvv變化顯著；氣道阻力份刪）增大，以7d吸氣阻力仰變化顯著：肺順應性k1 ）變化不大。
  7. Starting from the frozen food and refrigeration principles and using comparative analysis method, we get conclusions that in the blow - frozen device, the open - mode, cold - quantity reclaim, low - press, direct - cooling air, absorbing - heat air cycle have the most significant reductions in food freeze dry cost, food hygiene, devices delicate, organizating air stream, non - electrical heat, high efficiency and safe refrigeration etc. the cold - cumulating and dryness tin is the equipment which applys the store - release characteristic of cold - cumulating stuff, ensures the higher efficiency of open - mode cold - quantity reclaim low - press direct - cooling air, shoulders conveyance of the saturated and frozen air to frozen storeroom to reduce dry cost of food and dry the cycling air to ensure safe and reliable

    從食品冷凍和製冷原理入手，用對比分析方式得到了在吹風式凍結裝置中，開式回冷低壓直接冷卻吸熱循環空氣製冷機具有最大幅度降低食品凍結乾耗、確保食品冷凍安全、系統簡單、凍結庫小巧、氣流易於組織、無電機熱量、效率較高和製冷安全等結論。蓄冷乾燥器是通過蓄冷材料的蓄?釋冷特性，來保證開式回冷低壓直接冷卻吸熱循環空氣製冷機具有較高的效率，同時蓄冷乾燥器還擔負著輸送飽和低溫空氣至凍結庫以降低食品凍結乾耗和乾燥循環空氣以確保整機安全可靠工作的主要設備。
分享友人
分享到 Line

分享到臉書