最理想的沖力 的英文怎麼說

中文拼音 [zuìlǐxiǎngdechōnglì]
最理想的沖力 英文
critical momentum
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 想 : 動詞1 （思索） think; ponder 2 （推測; 認為） suppose; reckon; consider; think 3 （希望; 打算） w...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 理想 : ideal
  1. Abstract : there are offered many ways how to improve work of a spark plug. but one of the m ost important problems has not been solved yet. this is a thermal mode operation of a spark plug. the ideal spark plug should be instantly heated at the moment of occurrence of a spark and instantly cooled down in expectation of the foll owing electrical pulse. thus it balances between preservation of heat for self ? c leaning from scale and its removal in avoidance self ? ignition. in this article a uthor managed for this time to offer a spark plug with capability “ self ? regula tion ” of heat flux removed from a zone of ignition. essence of the offer is a t ip ， which is transparent for heat flux. it is produced from single crystal of sap phire

    文摘:在如何提高火花塞的工作質量方面有多種方法，但是其中最重要的一個問題還沒有得到解決，那就是火花塞工作的熱學模型問題.理想的火花塞應該能在點火的瞬間被立刻加熱，並且在接下來的電脈沖過程中迅速冷卻，由此在熱量的存儲與散發之間取得平衡，以避免自點火.本文力圖展示一種具有自動調節源於點火區域熱流能力的火花塞，其技術的關鍵是頂部絕緣體材料，它是由藍寶石單晶製作，而非傳統的氧化鋁陶瓷
  2. Presents the investigation of the heat conduction behavior, internal thermal stress field of specimen under thermal shock and microscopic damage and failure of the tungsten based composites by combination of macroscopic and microscopic analyses and integration of material science and mechanics ; describes a microscopic mechanical model based on the microstructure of components with macroscopic stress applied to the microscopic model as that of maximum principal stress at the center, and the fringe of the specimen, and the microscopic stress fields obtained through calculation by the finite element method, and concludes from test results that the maximum principal stress is first generated inside the test coupon, and a failure will be first initiated in the inclusion if the material fails at this time ; the maximum principal stress moves to the edge of the test coupon after the test coupon is heated for a period of time, and the failure will first be initiated in the base if the material fails at this time

    從材料設計的思想出發，採用宏觀與微觀、材料科學與力學相結合的方法，對鎢基復合材料的熱傳導行為、材料在熱沖擊載荷下的內部熱應力場及材料細觀結構的破壞行為進行了詳細的理論研究.根據鎢基復合材料的細觀組織結構建立了材料細觀模型.在宏觀分析的基礎上，分析了材料微結構內部的破壞行為.分別取試件心部與邊緣主應力值最大點的應力狀態，施加在所建立的模型上，用有限元方法計算了模型內部的彈性應力場.結果表明：試件主應力最大值首先產生在試件內部，此時，如果材料發生破壞將先從夾雜中開始；加熱一段時間后試件中的最大主應力值轉移到試件邊緣，此時材料發生破壞將先從基體中開始
分享友人
分享到 Line

分享到臉書