有燃燒作用的 的英文怎麼說

中文拼音 [yǒuránshāozuòyòngde]
有燃燒作用的 英文
incendiary
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing

    文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力
  2. Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading

    文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點
  3. As the result, we found natural scale graphite. expanded graphite by self - made, expanded graphite all had a certain flam - retardant effect and the composite inclusive of expanded graphite had the best flam - retardant effect

    論文同時還據于石墨阻燃的特性，測試了復合材料的燃燒性能，結果表明，天然鱗片石墨、膨脹石墨、膨化石墨都具有一定的阻燃作用，以膨化石墨的阻燃效果最佳。
  4. But the temperature difference at the vertical direction in combustion chamber in lead column, that is said by operator, is over 60 ?. ( 2 ) according to the experiences in the practice, the second layer air and the second layer gas had a little effect of support burning, and the third air has little effect for combustion, and the power to drawing exhaust gas can only be adjusted in limited range. the problems, it is said above, restricted more advance of some kinds of technology and economy target in spelter refining in new jersey furnace

    由於鋅精餾爐產量提高，一些問題開始暴露出來： （ 1 ）燃燒室?舶要求溫度差不超過10 ，而從現場反映的情況來看，燃燒室上、中、下部溫度差已超過60 ； （ 2 ）在生產實踐中，發現燃燒室第二層空氣、第二層煤氣作用甚小，第三層空氣失去助燃作用，廢氣出口的抽力可調范圍有限；以上這些問題在客觀上制約了精餾塔在鋅精煉中各項技術經濟指標的進一步提高。
  5. In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys

    本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。
  6. Submerged combustion with high efficiency and less pollution using in gas boiler has the characteristics of high heat transfer efficiency and saving energy

    浸沒燃燒法作為一種高效無污染的傳熱方法用於小型燃氣鍋爐，具有傳熱效率高、節約燃料的特點。
  7. The magnesium alloy is considered as this metal incendiary agent. changing the components of the traditional magnesium alloy, we find a new magnesium alloy, which can set fire to the wooden ammunition chests more effectively

    確定用鎂基合金作為此種高能燃燒劑，針對傳統鎂基合金產生熱量不足的缺點，通過添加某種金屬元素改變其組成成分，得到具有良好縱火效果的新型鎂基合金。
  8. Results show that all the geometric parameters have remarkable effects on combustion performance ; the swirl of intake air generated by skew intake holes enhances fuel - air mixing, minimizes dead zone and stabilizes the flame with reverse flow, but the excessive reverse flow can cause overheat in combustion chamber and exhaust ; the consistency of flow resistance in intake and exhaust system is conducive to the stability of heater performance

    研究表明，燃燒室進氣孔的孔徑、孔數、孔的分佈及方向等均對燃燒性能影響很大；斜孔所產生的旋轉進氣，雖具有強化燃氣混合、消除死區和迴流穩焰的作用，但迴流過度會使燃燒室及排溫過高；保證進排氣系統流動阻力（壓力）的一致性，有助於保證加熱器性能穩定。
  9. ( l ) it is very important for the state repair of diesel enging in our country ; ( 2 ) it will help with the more accurate decicision of repair cycle of the engine ; ( 3 ) it will improve the combustion state of the diesel enging and will keep the oil comsume at a lower level, at the same time, it lessens the dilute of the lubricanting oill in the engine. there are still some more research work to do, for it is just the begining. the mathematic model should be made and more accurate data rule should be established

    （ 1 ）為推行內燃機車狀態修做準備，這在跟蹤國際機車檢修先進技術上有著十分重要的意義； （ 2 ）為更合理制定內燃機車的檢修周期提供實驗分析方法和數據，試驗數據作為每臺柴油機的技術資料被存儲，藉助計算機軟體系統可以輔助制定機車的檢修計劃，使機車的檢修工作更科學合理； （ 3 ）提高機車質量，降低檢修費用； （ 4 ）改善柴油機燃燒狀態，降低燃耗，節約運營成本，同時，可以減少燃油滴漏，降低滑油消耗。
  10. In an igcc system coal is not burned but rather partially oxidized ( reacted with limited quantities of oxygen from an air separation plant, and with steam ) at high pressure in a gasifier

    在igcc系統則不燃燒煤，而是讓煤在與空氣隔絕的高壓氣化爐中，與有限的氧氣和蒸汽一同作用，進行部份氧化。
  11. Heating boilers - part 6 : heating boilers with forced draught burners - specific requirements for the domestic hot water operation of combination boilers with atomizing oil burners of nominal heat input not exceeding 70 kw

    供暖鍋爐.第6部分:帶有強制通風燃燒器的供暖鍋爐.帶有公稱熱輸入功率不超過70kv的自動燃油燃燒器的組合鍋爐家用熱水供暖操作的特定要求
  12. All adjustments ( burner height, burner arm length from the pivot point, counterweight positions along the burner arm ) are facilitated by the use of knobs or thumbscrews as the set screws

    所有調節（燃燒器高度、自樞軸點開始的燃燒器臂長、沿著燃燒器臂的平衡塊位置）都利用旋鈕或指旋螺釘作為調節螺釘實施。
  13. Based on detailed analyze on turbine engine and ramjet, a new conceptive internal - rotor burnt rotating ramjet ( irbrr ) with an rotating cylinder in the center of rotor in which the revolved stream can be ram - compressed and burnt has been proposed and some primary research have been done as below : the scheme of structure, principles, thermodynamic cycle and performances of the new conceptive engine has been studied in the paper

    本文通過對燃氣渦輪發動機和航空沖壓發動機的原理結構進行詳細分析並進行融合創新，提出了一種利用內置旋轉汽缸進行旋轉氣流沖壓壓縮和旋流燃燒的新概念內置燃燒室旋轉沖壓發動機，並進行了一些前期的基礎性探索研究，具體研究內容有:對旋轉沖壓發動機進行了總體方案設計、工作原理分析、氣動熱力循環和性能分析等概念性研究。
  14. Moreover, it has been pointed out that the hydrogen engine used in ? cylinder injection with high pressure can increase volumetric efficiency and compression ratio, - therefore, the performance indexes in this engine, such as output power, thermal efficiency, range of thickness of mixture with normal operation and nox emission, can be improved, and it is possible for the engine to realize rapid combustion of thin mixture, so abnormal combustion, such as backfire, pre ? ignition, can be controlled effectively

    指出了採用內部混合氣形成方式且高壓噴射的氫發動機，有利於提高充氣效率和壓縮比，從而改善發動機的動力性和經濟性；有利於擴展發動機正常工作的濃度范圍；並且有利於實現稀薄混合氣快速燃燒，從而可以有效地抑制早燃、回火及爆燃等異常燃燒和no _ x排放量。試驗指出了發動機的點火正時、噴射正時及噴氫量對發動機的性能、異常燃燒、 no _ x排放量有很大影響。
  15. Although these two algorithms are mainly to burning control system of boiler, they can also be reference effect on other similar control system

    我們所設計的這兩種演算法主要針對鍋爐燃燒控制系統，但對其它類似控制系統也有借鑒作用。
  16. With the rapid development of computational fluid dynamics and combustion theory, applying the computer to numerically simulate the complicated processes in the plasma ignition is possible. using numerical simulation can estimate the parameters which are not essay to measure and not doing so many experiments can improve its reliability and reduce the cost. so numerical simulation is a new pattern way to study the inner mechanism of the plasma ignition

    隨著計算流體力學和燃燒理論的發展及計算機的廣泛應用，用數值模擬等離子點火器內部燃燒系統流動、傳熱、傳質、化學反應等復雜的過程已成為可能。應用數值模擬的方法可以對實驗難以測量的量進行預估，而不需要大量的試驗，應用數值模擬的方法來解決等離子點火器燃燒性能的分析和工程設計，有利於提高工作的可靠性和經濟性。
  17. The disposal of the valves and intake manifold structure not only affect fresh air charge but airflow in the cylinder, which immediately affect combustion efficiency and the performance of dynamic, economic and emission. the structure of the air distributing institution has influence on charging efficiency and the noise of engine. the combustion chamber affects compression scale which has great influence on dynamical performance ; f / v which affects the exhaust of hc ; squash area and clearance which have great influence on the intensity of squash

    氣缸蓋的氣門排列方式與氣道結構形式影響進氣充量和氣流在氣缸內的運動，從而影響了燃燒效率，對整機的動力性、經濟性以及排放都有直接的影響；配氣機構的形式影響充氣系數和整機噪聲等；缸蓋燃燒室決定了影響整機動力性能的壓縮比，影響hc排放的f / v和對擠流起決定性作用的擠氣面積以及擠氣間隙，所以燃燒室對整機動力性、經濟性、排放等都有重要的影響；氣缸蓋是整機熱負荷與熱應力最大的部件之一，熱負荷過高將不利於發動機壽命以及可靠性的提高。
  18. Finally, the paper summarized all research conclusions, and proposed some reformative advices on such techniques of the rbcc secondary combustion organization, including the necessity, the feasibility and the practical value of hardware and software being migrated to a single chip in the future were also referred, so that some theoretic provisions and tech supports are offered to the investigations of rbcc

    最後，本文總結了將模糊控制方法應用於rbcc二次燃燒組織方面的研究結論，並提出改進建議，包括未來將有關軟、硬體系統移植到單片機上的必要性、可行性和實際價值等等。論文的工作將為rbcc燃燒組織的進一步縱深研究提供一定的理論準備和技術支持。
  19. Scramjet combustor may realize the subsonic - combustion mode and supersonic - combustion mode respectively based on the control of fuel in variable flight conditions. isolator has great effect on mode transition and preventing unstart of inlet. inlet can be unstarted by raising the back pressure result from chemical energy release in the combustor

    計算研究表明，在相同的來流條件下，供油規律對燃燒室的工作模態有著重大的影響；在不同的來流條件下，可以通過調節供油規律使燃燒室分別實現亞燃模態和超燃模態；隔離段對防止燃燒引起的壓力升高對進氣道的干擾和燃燒室的模態轉換具有重要的作用。
  20. The effects of the content, granularity and purity of the raw materials ( zirconium powder, viton and dicyandiamide ) on the combustion rate were measured and their effects on its detonation heat and its combustion heat were estimated. the investigation on the combustion reaction mechanism showed that surface decomposition of dicyandiamide was the control step of the combustion reaction. the slowdown and combustion - resistant effects of dicyandiamide were of endothermic characteristic

    測量了鋯粉、氟橡膠、雙氰胺等原材料含量、粒度、純度等對藥劑燃速的影響，估算了它們對藥劑爆熱和燃燒熱的影響，並對藥劑燃燒反應機理進行了探索研究，發現雙氰胺的表面分解是藥劑燃燒反應的控制步驟，其減速、阻燃作用具有吸熱特徵，氟橡膠對藥劑的熱輸出有較大貢獻。
分享友人
分享到 Line

分享到臉書