有缺陷的焊縫 的英文怎麼說

中文拼音 [yǒuquēxiàndehànféng]
有缺陷的焊縫 英文
poor weld
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 陷 : Ⅰ名詞1 （陷阱） pitfall; trap2 （缺點） defect; deficiency Ⅱ動詞1 （掉進） get stuck or bogged do...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
  1. The comprehensive effect of partial acidlity of working medium, flowing status of fluid, nocuous material in atmosphere, together with the overlong usage, largely increased the corrosion rate and caused the leakage

    結果表明，泄漏的主要原因是焊接缺陷導致焊縫區發生縫隙腐蝕，而工作介質的局部酸性、流體的流動形態、大氣中有害物質、溫差應力等綜合作用，加上使用期過長等加劇了腐蝕，導致該塔泄漏。
  2. The failure analysis of the heating jacket indicates that the austenitic stainless steel 316l is susceptible to stress corrosion cracking under the combined action of chloride environment and residual stresses induced by welding

    結果表明：加熱夾套開裂的主要原因是316l奧氏體不銹鋼不耐氯化物腐性，焊縫有一定的缺陷和腐蝕介質存在，屬於一種典型的應力腐蝕失效形式。
  3. It has mang virtues such as weld moulding beauty, weld quanlity credibility and so on, espcially it can conquer not weld fully, not fusion and so forth fatal vice

    它具有焊縫成型美觀、焊接質量可靠等優點，特別是對克服常規焊接方法中的未焊透、未熔合等危險性缺陷具有重要意義。
  4. The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts, corrosion, cracks, denting, initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper

    本文考慮板中可能存在孔洞、腐蝕、裂縫、局部撞損和初始焊接變形或殘余應力等損傷和初始缺陷，對不同的損傷形式用有限元程序（ ansys ）進行大量的計算，通過曲線擬合的方法引入折減系數對完好板格的有效寬度進行修正。
  5. The system can simulate welding expert to help technicians to complete procedure parameter design, set down wps and save them. besides the mechanical property and chemical composition of low carbon & low alloy steel, the weldabiliry and the defect forming analysis of them have been given in the system. furthermore, the estimation of welding cost and welding procedure files management can be accomplished

    系統能模擬焊接領域專家輔助設計人員進行焊接工藝參數的設計，編制出wps並保存文件；能進行簡單的焊接成本估算；能實現鐵路、橋梁及其它鋼結構生產中常用的低碳及低合金鋼及其焊接材料的力學性能和化學成分的查詢；能進行母材焊接工藝性以及常見焊縫缺陷成因分析與對策等的咨詢；能對各工藝文件進行有效的管理，包括對圖片的管理，能實現簡便地查詢、靈活地調用等。
  6. The paper expounds how to find out the potential safe problems and unobvious defects, such as beyond - limit deflection in fixed girders for gantry bucket wheel stacker / reclaimer, by means of completely checking fixed girders, movable beams, geometric shapes of stiff and flexible supporters, metal thickness and welding and how to solve the safe problems and remove the defects

    摘要通過對門式斗輪堆取料機固定梁、活動梁、剛性支腿、撓性支腿的幾何形狀、金屬厚度、焊縫狀況、聯接螺栓狀況進行全面檢測，發現門式斗輪堆取料機固定梁存在下撓超標的安全隱患和其他非明顯缺陷，從而對堆取料機的安全狀況有了全面的掌握，並根據檢測結論對固定梁下撓缺陷及時進行校正消缺，避免發生設備垮塌事故，保證了堆取料機的安全穩定運行。
  7. The welding line microstructure of ticp / fe in situ composites gained by different welding technologies and welding methods was different. however the microstructure was diffused on the welding line and there were no welding defects, the welding quality was better. the tic reinforced particles on the welding line still kept the same shape as that of the casting microstructure

    原位tic _ p fe復合材料採用不同焊接工藝和焊接方法所得的焊縫組織有所差別，但焊縫處的組織均勻，沒有裂紋等焊接缺陷產生，可焊性較好；焊縫處的tic增強顆粒仍保持鑄態組織中tic增強顆粒的形態。
  8. Welding and allied processes. resistance spot, projection and seam welded lap joints. classification of defects with explanatory comments

    焊接和有關技術.電阻點焊凸焊或縫焊搭接接頭.帶解釋的缺陷分類
分享友人
分享到 Line

分享到臉書