有限體 的英文怎麼說

中文拼音 [yǒuxiàntǐ]
有限體 英文
finite field
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 體 : 體構詞成分。
  • 有限 : limited; restricted; finite; a little; not much
  1. Finite volume method in thermal analysis of avionics

    高可靠性航空電子設備熱分析中的有限體積法
  2. The integral equations governing the three - dimensional viscous flow inside the turbo - machinery in the rotating coordinate system are presented in this paper, the viscous effects are simulated by the distributed body force described by professor denton j. d. the time - marching method and explicit finite volume difference scheme are employed to solve the flow inside the turbo - machinery

    本文給出了相對旋轉坐標系下葉輪機械內部三維粘性流動的守恆型積分型方程組，利用dentonj . d .教授的粘性體積力法來模擬粘性對葉輪機械內部流動的影響，採用時間推進法和有限體積差分格式對葉輪機械內部的流動進行求解。
  3. In the paper, river and the downstream area of dike are regarded as a whole system, and hydraulic model of coupling 1 - d river and gradual dike - break is established, therein the preissmann implicit difference scheme is applied to main river, and the fvm ( finite volume method ) is applied to the breach and polder

    本文將河道與堤壩下游區域視為一個整體，對于單一河道採用preissmann四點隱式差分格式計算，對于潰口及圩區採用有限體積法，建立了一維河道與堤壩漸潰耦聯的水力模型，也是一維、二維耦合的水流模型。
  4. Finite volume method is appilied in numerical modeling of the flow in no - pressure tunnel of high water reservoir in this paper. i select standard k - turbulence modeling that put forward by launder and spalding in 1972 by weighted poly - turbulence modeling. the difficulty is that there is free surface in flow, but free surface problem ' s calculating region is indefinitely

    本文利用有限體積法對高水頭下水庫無壓泄水洞水流進行了紊流數值模擬，根據多種紊流模型的優缺點進行比較，選擇了launder和spalding於1972年提出的標準的k ?紊流模型。
  5. It adopts reynolds time - average n - s equation and k - ? turbulence model to calculate the inner 3 - d viscid turbulence flow of centrifugal pump. in the unstructured grid, the governing equations are discretized with finite volume method based on finite element method. then the pressure correction method is used to carry out numerical calculation

    而後採用基於雷諾時均n - s方程與標準-湍流模型來求解離心泵葉輪內三維粘性紊流，在非結構化網格中，採用基於有限元的有限體積法對方程進行離散，用壓力校正法進行數值求解。
  6. Firstly, the computer simulating model of the limited volume unit is established. then pet is chosen as sample. generally, under predetermined nucleation condition, the course of pet isothermally crystallized at 170 c in limited volume unit is simulated

    計算機模擬實驗首先建立了有限體積元模型，然後選定了pet為樣品，一般模擬其在預先成核條件下、 170時的等溫結晶過程。
  7. In this paper, the course of isothermal crystallization kinetics of polymer in limited volume unit is simulated by use of the method of monte carlo. four factors influenting on the course of polymer in the limited volume unite isothermal crystallization are analyzed under the given conditions. the four factors are sample volume shrinkage, the change of the linear growth rate of entities g, the change of sample thickness and the change of the number of nuclei

    本文採用montecarlo方法研究了高聚物在有限體積元中的等溫結晶動力學過程，分析了在一定條件下，樣品體積收縮、晶體線生長速率變化、樣品厚度變化和晶核數目變化這四種因素對高聚物在有限體積元中的等溫結晶過程的影響。
  8. The results show that it is the numerical method of high analyzable degree for the hybrid tvd scheme combinated with fvm, and the scheme is not only sufficiently accurate and nonoscillatory, but also capable of treating automatically hydraulic jump

    算例驗證表明：應用組合型tvd ? muscl格式配合有限體積法是一種高解析度的數值方法，且tvd ? muscl格式對于自動捕捉激波和抑制間斷附近的數值解波動十分有效，它對間斷具有高解析度。
  9. 4. a 2 - d and 3 - d euler equations and n - s equations are solved using the cell - centered finite volume method and four - step runge - kutta scheme on the cartesian grids with standard convergence acceleration techniques such as local time stepping, enthalpy and implicit residual smoothing

    使用jameson中心有限體積法和runge - kutta時間推進方法，求解了關於二維、三維復雜流場的euler 、 navier - stokes方程，採用了當地時間步長、隱式殘值光順等多種加速收斂方法。
  10. Compared with octree data structure, the omni - tree data structure could reduce the meshes " total numbers and get better mesh quality. this paper uses cell - centered finite volume spatial discretization and four - stage runge - kutta time - stepping scheme with some convergence acceleration techniques such as local time stepping and enthalpy damping

    在流場計算中，本文採用格心格式的有限體積法用二階中心差分對歐拉方程作空間離散，用四步龍格庫塔方法作顯式時間推進。
  11. In this paper, the upwind scheme and the central scheme are presented for solving 3 - d n - s equations using the cell - center finite volume spatial discretization and four - stage runge - kutta time stepping scheme, with standard convergence acceleration techniques such as local time stepping and implicit residual smoothing

    在n - s方程的數值計算上，採用了中心差分格式和迎風格式，用格心格式的有限體積法進行了空間離散，用四步龍格?庫塔法作顯式時間推進，並採用了當地時間步長和隱式殘差光順等加速收斂措施。
  12. Shock tube ; conical convergent section ; detonation ; finite volume tvd scheme

    激波管收縮截面爆轟有限體積tvd格式
  13. The numerical simulation of axisymmetric two - dimensional shock tube is studied, which has a conical convergent section, and its driving gas is the hot product of hydrogen oxygen detonation. finite volume tvd scheme is adopted and the mesh is local orthogonal. the primitive equations are euler s equations of multi - component flow. the new method of eliminating numerical oscillation at the interface of two materials is extended to two dimensions. the mechanical character of this shock tube is analyzed

    對由前向爆轟產生驅動氣體並具有局部錐形收縮截面的軸對稱激波管利用兩相常比熱完全氣體的歐拉方程組和有限體積tvd格式在局部正交的網格上進行了二維數值模擬。將消除兩種介質界面處數值振蕩的新方法成功地推廣到二維情況。分析了該激波管的力學特性。
  14. In this paper, we develop the high - order accurate essentially non - oscillatory ( eno ) schemes on one and two - dimensional structured meshes in the finite volume formulation, and discuss their applications in hyperbolic conservation laws

    本文構造了一維、二維結構網格中的高階精度基本無振蕩（ eno ）有限體積格式，並且討論了它在雙曲守恆型方程中的應用。
  15. Modeling of aluminum profiele extrusion processes using finite

    鋁型材擠壓過程有限體積法數值模擬技術研究
  16. The numerical algorithm of solving the adjoint equations for different design cases have been developed by using finite volume methodology which is usually used to solve the flow governed equation. it includes the some important aspects, such as flux formulation, wall and far - field boundary treatment methodology, dissipative term formulation, etc. after the solution of the adjoint equations is obtained, the derivatives of the cost function with respect to all the design variables can be evaluated with the same operation. this can yields a significant saving over the other gradient - based techniques when there are many design variables

    （ 3 ）進行了應用控制理論和三維歐拉方程的機翼氣動反設計研究，以及有升力約束情形下機翼跨音速減阻問題研究，分別推導了相應的共軛方程及邊界條件數學表達形式，研究與發展了三維共軛方程的有限體積數值求解方法，及相應梯度公式的數值求解方法，通過對計算網格生成、流場計算、共軛方程數值求解、梯度求解和優化演算法等多方面的有效結合，成功發展了三維機翼的氣動反設計和跨音速減阻優化設計程序，成功地進行了多個設計算例研究。
  17. A high - resolution finite volume method 2d shallow water equations

    求解二維淺水方程的一種高解析度有限體積法
  18. A new finite volume method for two dimensional convection - diffusion problems

    二維擴散輸移問題的一種新的有限體積演算法
  19. Finite volume method, fvm

    網格的有限體積法
  20. Numerical simulation of square cavity flow by second - order up - wind finite volume method

    二階迎風有限體積法方腔流數值模擬
分享友人
分享到 Line

分享到臉書