板材軋輥 的英文怎麼說
中文拼音 [bǎncáiyàgǔn]
板材軋輥
英文
plate roll- 板 : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
- 材 : 名詞1 (木料) timber 2 (泛指可以直接製成成品的東西; 材料) material 3 (供寫作或參考的資料) ma...
- 軋 : 軋動詞[方言]1 (擠) press hard against each other; push against2 (結交) associate with; make f...
- 輥 : 名詞[機械工程] (能滾動的圓柱形機件) roller
- 板材 : panel; slab; [林學] board; plates; sheet material; steel sheet
-
Our rubber roller products are complete in series and meet all the specifcation requirements. they are used in printing houses, paper mills, dye - works, textile mills, plastic processing works, steel rolling plants, timber ( plank ) processing works, office automation equipment, etc. gd xinli produces water rollers, uv rollers, rollers that can resist different kinds of chemical solvents, rollers that can resist acidalkaline, polishing rollers, polyurethane rollers, etc. the annual amount of production reaches 120 tons
規格品種齊全,適用於印刷、造紙、印染、紡織、塑料加工、軋鋼、膠合板(木材加工)和辦公自動化設備等。例如水輥、 uv輥、耐各種化學溶劑膠輥、耐酸堿膠輥、磨光輥、聚氨酯膠輥等。年產量達120噸。Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle , 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got
對雙金屬復合板成型過程進行模擬,從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律,復合后的齒形的變形情況與初始齒形形成對比,以動畫的方式模擬成型過程,並分析了不同幾何參數(主要是不同的齒型,其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型) 、材料參數、工藝參數對復合強度的影響,以及不同齒型的變形對比以及齒型對復合情況的影響,提出最優齒型、最優工藝參數,有效地指導了實驗。The model considers not only the slab bounce on gauge and hardness, obverse and inverse bounce on width, and the rolling length constraint of the slabs with same width, but also the reasonable arranging of warm - up materials and staple materials
該模型不僅考慮了軋制計劃中板坯在厚度和硬度上的跳躍、板坯寬度的正反跳以及相同寬度板坯連續軋制的長度約束,而且考慮了軋制計劃中燙輥材和主體材的合理安排。And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array
本文採用ansys / ls - dyna計算程序為分析工具,對鋸齒形雙金屬復合板成型過程進行計算機數值模擬,在對軋制過程模擬時,針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題,給出了在ansys / ls - dyna中相應的解決方法:應用nodetosurface接觸方式,設定相應參數,選用雙線性等向硬化模型,載荷作為array施加在剛體質心。The soft to medium - hard feed material is fed to a wedge - shaped crushing area by conveying devices and is crushed between crushing plate and rotating crushing roll fitted with mounted crushing tools
由從軟到中硬材料所組成的給料被輸送設備輸送到一個楔狀破碎空間,在破碎板條和旋轉的破碎軋輥之間被破碎。The demand to the precision of steel plate in industry production has enhanced increasingly, but the surface precision of roller, which affects the precision of plate material seriously, will debase because it is worn
=工業生產對所需板材精度的要求日益提高,但由於軋輥在使用中不斷磨損變形,導致其表面精度降低,從而嚴重影響著所生產的板材的精度。Hongtai steel flat plate, which adopts excellent color - coated plates, are roof and wall materials after being rolled on automatic production line, it owns merits of lightness, strength, bright color, beautiful appearance
鴻泰鋼構面板採用優質的彩色塗層鋼板,經自動型生產線輥軋而成的屋面和墻面材料。分享友人