板極間距 的英文怎麼說

中文拼音 [bǎnjíjiānjù]
板極間距 英文
plate clearance
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 距 : Ⅰ名詞1 （距離） distance 2 （雄雞、雉等的腿的後面突出像腳趾的部分） spur （of a cock etc ）Ⅱ動詞...
  • 間距 : interval; separation; spacing; espacement; space; spacing; space length; range; unpack; step
  1. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  2. The structure of the modern woodwork, processing quality has proposed higher demand to the wood processing equipment, for instance : wooden tenon position public errand, hole of interval, modes in chinese operatic music of furniture must high many rows of drill is it realize to come very by precision, panel unloading to is it realize to come by accurate person who cuts out board, is it is it is it is it sharpen by accurate numerical control machining center is it realize to come to mill to process to pare to milling extremely high of imitating etc.

    現代建築裝飾及家具行業的發展與加工設備是休戚相關的。現代木製品的結構加工質量對木材加工設備提出了較高的要求，如：板式傢具的木榫孔間距的位置公差必須由精度很高的多排鉆來實現，板材下料是由精密裁板機來實現，仿型極高的銑削加工是由精密數控銑削加工中心來實現的。
  3. When the element of array is near enough, the stacked tem - horn array can improve the radiation of lower frequency

    當陣列疊狀排列並且相鄰陣列單元極板間距較小時，可以改善低頻輻射特性。
  4. Big space between mold plate, better rigidity, very convient in components embeded operation, also can heigten the pillars of manchine, extend the space capacity of mold

    模板間距大，剛性佳，嵌件作業極為方便。並可加高機柱，增大容模空間。
  5. For three degrees of freedom system, with the increasing of plate distance, the frequency of circuit system 1 increases

    電路系統的固有頻率隨極板間距的增大而增大，隨極板面積和電感的增大而減小。
  6. They are as follows : powder types, electrode voltage and board space etc. and the optimized parameters obtained in the normal temperature spray experiments were applied in the thermal spray

    通過冷噴實驗，找到了影響收集西安理工大學碩士學位論文效率的因素有:粉末類型、電極電壓以及極板間距等。並將冷噴時的最佳參數應用於熱噴塗制粉末的收集中。
  7. The results show that the elastic membrane thickness, actuator span and gap spacing have a strong effect on the deflection, the actuator undergoes the deflection increasing nonlinearly at voltages below pull - in voltage and snap through instability at voltages above pull - in voltage when subjected to a voltage ramp, the re - set time and repeatability are attractive when the actuated voltage is set to zero

    結果表明，驅動器的彈性薄板厚度、跨度和電極間距明顯影響變形位移；驅動器的變形位移隨驅動電壓的增加出現穩定的非線性增加和不穩定的「拉入」現象；驅動電壓撤除后鏡面回復時間短，重復性好。
  8. In the case of small molecule, the film of tcnq and snpc was prepared by thermal vacuum evaporation. the effect of substrate temperature on the surface morphology and the conductance of the thin film has been investigated. the relation between the sensitivity of thin film and temperature of the substrate was described

    對于兩種小分子材料，本文先採用真空蒸發的工藝制備敏感薄膜，探討了不同基板溫度對薄膜表面形態、膜的導電性的影響，並進一步分析了基板溫度、膜厚和電極間距對傳感器敏感特性的影響。
分享友人
分享到 Line

分享到臉書