柱的縱向彎曲 的英文怎麼說

中文拼音 [zhùdezōngxiàngwānqū]
柱的縱向彎曲 英文
column deflection
  • 的 : 4次方是 The fourth power of 2 is direction
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 縱向 : [造紙] direction; machine direction; endwise; longitudinal direction; vertical; longitudinal縱向...
  1. Columns under axial compression and biaxial bending. in the beginning of the paper, it summarized the history and the actuality of the nonlinear analysis of special - shaped columns and the capability of the sliding of reinforcement anchoring. on the basis of related papers, the full path of stress - strain relation of concrete and the sliding of longitudinal reinforcement anchoring are all considered

    本論文主要內容是對鋼筋混凝土異形截面雙向壓彎柱（包括l形、 t形、十字形柱）進行非線形全過程分析，首先綜述了異形柱構件非線性分析以及粘結滑移性能研究的歷史與現狀，在有關文獻基礎上考慮了受拉縱筋和周圍混凝土的粘結滑移和混凝土應力?應變關系曲線的下降段。
  2. The content of the paper is nonlinear analysis of complete response process for t, l - shaped and " + " shaped section r. c. columns under axial compression and biaxial bending. on the basis of related papers, the full path of stress - strain relation of concrete and the sliding of longitudinal reinforcement anchoring are all considered, simultaneously, the restriction effect for concrete by thickening of stirrups is also included

    本論文主要內容是對鋼筋混凝土異形截面雙向壓彎柱（包括l形、 t形、十字形柱）進行非線形全過程分析，在有關文獻基礎上考慮了受拉縱筋和周圍混凝土的錨固滑移和混凝土應力?應變關系曲線的下降段，同時考慮到在箍筋加密區箍筋對混凝土的約束影響。
  3. In the hogging condition, double bottom and the side shell remain the ultimate bucking strength, deck and upperwing tank remain the yield stress, and the other parts keep elasticity. then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels. in this regard, the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure. fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence. all possible collapse modes involed in collapse of stiffened panels, including overall buckling collapse, column or beam - column type collapse, tripping of stiffeners and local bukling of stiffened web are considered

    確定了船體梁整體破壞時的剖面應力分佈之後，關鍵在於確定板架的極限屈曲強度。本文充分考慮了在縱向彎曲、橫向壓力作用下加筋板可能發生的幾種破壞模式，即板架的整體屈曲破壞、樑柱形式的破壞、筋的側傾、腹板的屈曲並同時考慮了初始焊接殘余應力、初撓度的影響，使其更精確的計算加筋板的屈曲強度。對于加筋板中加強筋腹板的局部屈曲，採用解析法推導出筋的腹板的撓度方程及其邊界條件，求解相應的方程，從而計算出腹板的局部屈曲應力。
  4. The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone

    根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。
  5. Then, a step - by - step increase of vertical curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment. performing sample calculations on existing girder models tests under pure bending, the rationality of the proposed method was examined

    假設船體橫向框架材足夠強，因而板架的整體破壞不會發生；基於梁?柱理論、理想彈塑性假設、平面假設，建立了拉伸和壓縮加筋板單元的平均應力?應變關系曲線，應用船體結構總縱極限強度的簡化逐步破壞分析方法計算船體總縱極限彎矩，並據此開發了計算程序sus 。
分享友人
分享到 Line

分享到臉書