柱端條件 的英文怎麼說

中文拼音 [zhùduāntiáojiàn]
柱端條件 英文
column end conditions
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 條 : Ⅰ名詞1 （細長的樹枝） twig 2 （條子） slip; strip 3 （分項目的） item; article 4 （層次; 秩序; 條...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 條件 : 1. （客觀的因素） condition; term; factor 2. （提出的要求） requirement; prerequisite; qualification
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. ( 2 ) from the equilibrium conditions of the isolated segment from a beam - column sub - assemblage, it is clarified for the first time that the bond stress along the beam rebars passing through the joint transfers into the column end to balance shear at this column end at the same ratio as that of the compression force in the compressed concrete at beam ends

    通過對樑柱組合體柱脫離體的平衡條件，首次明確了貫穿節點梁筋粘結應力和梁端受壓混凝土的壓力以相同的比例傳入柱端以平衡柱端剪力，從而對節點區的傳力機理重慶大學博士學位論文結出了完整的和具有說服力的解釋。
  3. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  4. In this paper, the high - temperature low - cycle fatigue life and fatigue crack propagation life tests are carried on the cylindrical axial symmetry specimens having precrack or non - precrack with different types of notches of 16mnr steel in common use in the petrochemical industry contacting coke drum equipment, the stress / strain and the range of stress / strain of dangerous points are received through stress analysis of the specimens using finite element program under multi - axial stress state. at last, the equations of evaluating the high - temperature low - cycle fatigue life and the fatigue crack propagation life are found through using the least - square regression method

    本文採用無預裂紋和帶預裂紋環狀缺口圓柱形試樣，進行了石化焦炭塔設備常用材料16mnr多維應力狀態下不同缺口形式的高溫低周疲勞總壽命試驗及裂紋擴展壽命試驗，並利用有限元程序對試樣缺口周圍及裂紋尖端附近進行了軸對稱多維應力狀態下的應力、應變場分析，來評價材料不同條件下的高溫低周疲勞總壽命和裂紋擴展壽命，最後利用最小二乘回歸方法，得到了該材料高溫低周疲勞總壽命和裂紋擴展壽命評價方程。
  5. 4. choosing the reasonable deflection curve function. according to the energy method and the constrained condition of column end of the steel arch gate, the article presents a practical calculating formula for the stability of the main frame structure of the steel arch gate

    選擇合理的撓曲線函數（試解函數） ，根據能量法及弧門柱端約束條件，提出弧形鋼閘門主框架（平面鋼框架）穩定性計算的實用解析計算公式，並根據影響弧門主框架穩定性的因素對該公式進行修正。
  6. Type, dimensions and specifications of pn 250 mpa stud bolts at boss

    Pn250mpa階端雙頭螺柱型式尺寸和技術條件
  7. Besides, compariative analysis was carried out on ductility and energy comsumption of the interior joints on the top story with 90 ? bent hooks, exterior joints in the intermediate stories with different detailing of longintudinal reinforcement in the columns, and the knee joints with different lap splices in the beam and the column under negative moments. seismic anchorage and lap splices schemes were presented for the longitudinal rebars in the joint core

    此外重點對不同條件下中間層端節點梁筋帶90彎折錨固端的試驗結果、頂層中節點採取不同柱筋構造方案的試驗結果以及樑柱負彎矩筋採取不同搭接方案的頂層端節點的試驗結果的延性和耗能性進行了對比分析。
分享友人
分享到 Line

分享到臉書