栓固試驗 的英文怎麼說
中文拼音 [shuāngùshìyàn]
栓固試驗
英文
restrain test-
Advanced digital hardometers ( testing the hardness and safe load of bolts ) etc. testing equipments. advanced digital hardometers testing the hardness and safe load of bolts ) etc. testing equipments, the 1, 500 sq. m. vertical goods shelves can hold more than 5, 000 tons goods loading, each bin has fixed codes, and has perfect enterprise digital informationization management system and the support of software, which greatly improves the rationality and simplicity of goods loading and enhances the accuracy of goods and quick delivery and is one - up on others
先進的數字化硬度測試儀（檢測螺栓的硬度及保證載荷）等檢驗設備，以及1500平方米的立體貨架可容納5000多噸貨物的存放，每個倉位都固定編碼，並有完善的企業數字信息化管理體系及軟體的支持，大大提高了貨物堆放的合理性和簡潔性，大大提高了貨物的準確性和發貨的快速性，使得更勝人一籌！Plastics piping systems. glas - reinforced thermosetting plastics components. test methods to prove the design of bolted flange joints
塑料管道系統.玻璃纖維增強式熱固性塑料元件.檢驗栓接式法蘭接頭的設計試驗方法In this test, a special bolt - jack is used to exent of prestressing force to brace angles as the whole structure is under dead - load. in this state brace angles withstand partly load before twice - load and the stress and strain of concrete are decreased. in this way the aim of removal of load and strengthening can be reached
本試驗中採用專用螺栓千斤頂在恆定荷載水平下對混凝土柱角鋼撐桿施加預壓應力，使外包角鋼在二次受力前即分擔部分荷載，使混凝土應力水平和應變水平降低，達到卸載與加固同步進行的目的。Pressure seal design without live load bonnet ( no spring washers ) : the gasket bolt tightness must be rechecked after operating test pressure and temperature has been achieved
沒有動負載閥帽的壓力密封結構（沒有彈簧墊圈） ：在工作試驗壓力和溫度達到限制值時，必須重新檢查墊圈螺栓的緊固性。In order to solve it radically, making power assembly of bj1036e2f1 light truck the research object and through dynamic simulation analysis of power assembly, this thesis obtains the distribution rules of forces of the bolts linking three shells mentioned above and the relation between forces of the bolts and rotate speed of engine. after finite element mode analysis of these three shells, inherent frequency and vibration model of shell of power assembly are gained, and thus its dynamic character is realized. based on computer simulation analysis, experimental model of power assembly is acquired by vibration test and strength test of shell of power assembly, and the relation of forces of the shell and rotate speed of engine and imbalanced mass of rotate components is studied
為了從根本上解決該問題，本論文以bj1036e2f1輕卡動力總成為研究對象，通過動力總成的動力學模擬分析，找出了三殼之間聯接螺栓受力的分佈規律和螺栓受力與發動機轉速的關系；通過三殼的有限元模態分析，得到了動力總成殼體的固有頻率與振型，從而了解了動力總成殼體的動態特性；在計算機模擬分析的基礎上，通過動力總成殼體的振動測試和強度測試，得出了動力總成的試驗模態，並研究了殼體受力與發動機轉速和旋轉部件不平衡質量的關系。Summarizing the above - mentioned research results, the design method of two kinds of connection ways of steel braces is proposed, which include the calculation formula of the steel braces, the head studs, steel angels at four corners of beam and column and embedded steel framework
本文在上述試驗的基礎上，提出了兩種支撐加固連接方式的計算公式，包括支撐桿件、栓釘、外包鋼連接和鋼內框連接等。Mechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm
緊固件機械性能螺栓與螺釘的扭矩試驗和破壞扭矩公稱直徑1 10mmMechanical properties of fasteners - torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.標稱直徑為1mm到10mm的螺栓和螺釘的扭轉試驗和最小扭矩Mechanical properties of fasteners. part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件機械性能.第7部分:公稱直徑1 - 10mm的螺栓和螺釘的扭力試驗和最小扭矩Mechanical properties of fasteners part 7 : torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
緊固件的機械特性.第7部分:扭力試驗和標稱直徑為1mm - 10mm的螺栓和螺釘的最小扭矩分享友人