校對臂 的英文怎麼說
中文拼音 [jiàoduìbèi]
校對臂
英文
checking arm-
The manual introduced the total design and compute the process detailedly about the general design and the running gear design, which divided into altogether three chapter : chapter 1 for total design part of this crane, the main contents is each organization of crane and the metals structure patterns to really settle, and carry on the design to a structure of jib arm and counterbalance system by graphing method, including seeking the point, checking to calculate and school pit ; the second part is a design calculation that circulates the organization, including to circulate the organization to choose the type, the round presses calculation, the stability checking of the whole machine ; the third part is to choose the driving motion version of the hoisting mechanism
說明書詳細的介紹了該型號起重機的總體設計及行走機構設計和計算過程，總共分為三章：第一章為起重機總體設計部分，主要內容是起重機各機構和金屬結構型式的確定，並用作圖法對臂架結構和平衡系統進行設計，包括了機構找點，驗算及校核；第二部分是運行機構的設計計算，包括了運行機構的選型，輪壓計算，整機穩定性校核；第三部分為起升機構的傳動方案選型和設計計算。The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing
本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。The design manual falls into three parts : chapter 1, as the overal design part, mainly descirbes how to determine which mechanisms with what metal structures shall be used and illustrates how to design its boom structure and balancing system, including point search, calculation and check ; chapter 2 introduces how to design the crane ' s running gear, including model selection, wheel pressure calculation and overall stability check ; and chapter 3 deals with model selection of its lifting mechanism and related calculations
說明書詳細的介紹了該型號起重機的總體設計及行走機構設計和計算過程，總共分為三章：第一章為起重機總體設計部分，主要內容是起重機各機構和金屬結構型式的確定，並用作圖法對臂架結構和平衡系統進行設計，包括了機構找點，驗算及校核；第二部分是運行機構的設計計算，包括了運行機構的選型，輪壓計算，整機穩定性校核；第三部分為起升機構的傳動方案選型和設計計算。The method of indirectly measuring force exerted on ground by bucket is used to check cantilever bucket - wheel stacker / reclaimer counter - weight, working out the hydraulic cylinder force to determine the force exerted on ground by bucket and thus counterweight value
摘要針對懸臂斗輪堆取料機配重的校核提出了1種間接測定接地力的方法，即通過懸臂升降液壓缸上下油腔壓力計算出液壓缸受力，進一步推算出堆取料機的接地力，從而確定配重安裝量。Besides, this paper presents the designs for the twin - floater ocean wave generate electricity device, and verifies the intensity of the floating arm which is important for the design
本文給出雙浮子海浪發電裝置的總體設計簡圖以及其設計結構圖，並對設計的關鍵部分?浮子臂進行強度校核。Firstly, the design methods of main components of double - links independent suspension, including shock absorber " choosing, antiroll bar ' s calculation, torque bar spring ' s design, are presented and movement of double - links independent suspension is analysed. so a software which is used to design and analyse independent suspension is programmed. meanwhile, the experiment to verify the result is made with the equipment of the front wheel alignment
首先對雙橫臂獨立懸架的各主要組成部件如減振器的選型設計、橫向穩定桿的設計校核、扭桿彈簧設計以及對雙橫臂式和麥弗遜式獨立懸架的運動進行了分析，提出了相應的計算方法，編制了一套具有一定實用價值的前獨立懸架設計分析軟體。The image - based approach may reduce computational delay, eliminate the necessity for image interpretation and eliminate errors due to sensor modeling and camera calibration
該方法可以減少計算延時，並且對攝像機和機械臂的校準誤差和目標模型誤差具有較強的魯棒性。A method of choosing the wind load influence modulus that decides the wind load numerical value of combination structure was proposed correspondingly. firstly the wind load parameter that influences the wind load of combination structure was chosen according to design criterion of high - rising structure and through tradition calculation methods of wind load. by using currently calculation methods the axis force and martix of the most danger section was worked out, and the security of structure was analyzed and checked
首先運用傳統風荷載計算的方法，結合本文的組合結構的特殊情況，以高聳結構設計規范為參考，參照風荷載理論選定了影響該組合結構風荷載的風荷參數，並依據一般塔架演算法（簡化懸臂梁法）計算出了與底座連接處斷面（最危險截面，距塔底6米段）的軸力和彎矩，同時對此處進行了應力分析和可靠性校核。At the same time, this article has carried on the mode test to my school mechanics laboratory cantilever beam structure and the model wing two kind of structures, and particularly researched for the mode test as well as carried on processing to the test data
同時，本文對我校力學實驗室的懸臂梁結構和機翼模型兩種結構進行了模態試驗，並對試驗進行了詳細研究以及對試驗數據進行處理。分享友人