校準誤差 的英文怎麼說

中文拼音 [jiàozhǔnwùchā]
校準誤差 英文
alignment error
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 誤差 : error
  1. Since there are two completely separate tracking systems there must be some collimation error or disturbance c.

    由於存在兩個完全分離的跟蹤系統，所以一定有一些校準誤差或干擾量c。
  2. During the evaluation method for the precision of missile aiming on the sea, setting up test structure system, confirming demand coordinate, putting up installation and calibration to test frame of missile silo, in the course of navigating, it was analyzed and calculated the direction error that brought by the incorrectness of the position of longitude and latitude

    在海上瞄準精度鑒定方法中，建立了試驗構建體系，確定了必要的坐標系，對彈筒試驗支架進行了裝調、校正和實際標定。對艇在航行過程中，由於艇的經、緯度不準確而帶來的定位誤差的影響進行了分析與討論。
  3. Volumetric distribution feature of measuring coordinate errors integrating with nonrigid errors

    三坐標測量機探針校準的誤差分析
  4. On the part of the design of nine - component thrust vector stand, an automatic hydraulic pressure original position calibration system, a scheme of original position calibration, and the great rigidity universal flexible combinatorial underprop are designed. by using the scheme of “ universal flexible combinatorial underprop plus software digital filter ”, the inherent frequency of test stand is improved, and the problem of test stand libration is solved. then, the resolving method of the disturbance between underprops of the moveable frame is proposed, and the disturbance revise equation is deduced

    在推力矢量試車臺設計方面，設計了自動液壓原位校準系統、原位校準方案以及大剛度萬向柔性組合支撐;採用「萬向柔性組合支撐+軟體數字濾波」的方案，提高了試車臺動架的固有頻率，解決了試車臺動架的振動問題;提出了動架約束互擾問題的解決方法，推導了互擾修正方程;研究了九分力推力矢量測量誤差分析方法，並計算了推力矢量測量精度。
  5. The results of experiment verified the simulation of pspice software. in chapter five, the technology requirements of vibration calibration system are introduced, and thus the optical and electric design are realized. the laser - vibration - measuring - system is tested and the results are analyzed

    第五章介紹了振動校準系統對測振儀的技術要求，實現了相關光路和電路的設計；對系統進行測試，並對實測結果進行分析；最後對系統的誤差進行了分析。
  6. Correction the principle error of helmet - mounted electro - optical sight

    某型光電頭盔瞄準具原理誤差的校正
  7. Measurement errors analyses of network analyzer

    微波網路分析儀系統誤差辨析及校準
  8. The dissertation includes six chapters and the contents are as follow : in chapter 1, the characteristic and the signification of vibration transducers are depicted, and the methods and theirs errors of calibration are presented detailed. then, the general situation of the development of vcs in domestic and abroad is introduced. the important signification of improving the performances of vcs is expounded

    第一章敘述了振動傳感器特點及其校準工作的目的和意義，重點介紹了傳感器校準方法及其校準結果的誤差分析，同時分析了目前國內外振動傳感器校準系統的發展概況，闡述了改善振動傳感器校準系統性能的重要意義，最後提出了論文的主要研究內容。
  9. Correction of error to measure thermal parameter parastability of rubber material

    橡膠材料熱參數準穩態測量法的誤差校正
  10. Phases straight lines model and not straight lines model based on bp are used to correct the physical parameters and eliminate deflection. the least - square is used to calculate the efficiency of generators

    在物理量校準中利用分段直線回歸和基於神經網路的非線性回歸，對模擬量進行了非線性在線校正來消除誤差；在發電機效率計算中利用最小二乘法實現了發電機效率回歸。
  11. A resolution method in software is applied to calibrate zero point and full scale of the circuit. software approach to nonlinear correction for sensor and circuit is presented. therefore system error is eliminated, and measurement accuracy of temperature is improved. the signal of acidity electrode is detected by a differential amplifier circuit, which consists of operational amplifiers tlc2254 with high input impedance and low drift

    採用橋路和單運放差動放大電路對溫度傳感器信號檢測放大，軟體校正溫度傳感器和測量電路的非線性，軟體校準測量電路的零點和滿度，消除測量電路的系統誤差，提高補償溫度的測量精度；採用高阻、低漂移運放tlc2254組成高阻差動放大電路用於酸度電極信號測量。
  12. Based on the theory of charge calibration and sample and reconstruction of frequency limited signal, the scheme of adopting direct digital synthesizing technology and technology of computer is put forward in the paper. the design of hardware and software is described in detail, the error of the outputs signals of the high precision charge calibrator has been analyzed in theory

    文中基於電荷校準的原理及帶限信號的抽樣與重構理論，提出了採用直接數字合成技術與計算機技術的整體設計方案，詳細講述了硬體電路與系統軟體的設計過程，並對高精度電荷校準儀輸出信號的誤差進行了理論分析。
  13. For an instrument error of less than 3 %, calibrate the pressure - indicating device in such a manner that known pressures are applied dynamically at approximately the same rate as in testing of paper

    我的理解是:對于誤差少於3 %的機器，要在了解動態應用的壓力速度和紙試驗速度大約一樣的方式下校準指示壓力裝置。
  14. With the development of high - technology, all trades " production and development need electric power which is one of the main energy. so the accuracy of electrical parameter caculation is very important for our country ' s economic development. the normal usage of ac indictor is very important for guaranteeing electricity ' s safety production and accuracy of electrical parameter caculation. now the area of domestic ac indictor has lots of shortcomings such as demanding many people synchronous proceeding, equipment operation complicacy and personnel error etc. so it can not demand the need of modern ac indictor checking

    因此電參數計量的準確可靠，對保證我國經濟的發展至關重要。交流儀表的正常使用，對保證發供電的安全生產、電能計量的準確可靠、電參量量值傳遞的準確可靠，發揮著至關重要的作用。目前國內交流指示儀表領域存在需要多人同步進行、校驗設備多、操作復雜、人員誤差大和勞動效率底等諸多缺點，加之電工校驗臺技術等級低，已經無法滿足現代化校驗交流指示儀表的需要。
  15. 1 calibration the comparison of a measurement standard of instrument of known accuracy with another standard of instrument to detect, correlate, eliminate by adjustment, and report any variation in the accuracy of the item being compared

    調校把一部己知其準確度的儀器的量度標準與另一儀器的標準作比較，來檢查、連系、更正並消除及報告比較專案的誤差。
  16. Since there are two completely separate tracking systems there must be some collimation error or disturbance c

    由於存在兩個完全分離的跟蹤系統，所以一定有一些校準誤差或干擾量c 。
  17. Secondly, the calibration model for the system is proposed, and the calibration errors can be analyzed based on this model

    其次提出了低頻uwb - sar輻射校準模型，通過該模型可以分析校準誤差和各個參數的測量誤差的關系。
  18. The image - based approach may reduce computational delay, eliminate the necessity for image interpretation and eliminate errors due to sensor modeling and camera calibration

    該方法可以減少計算延時，並且對攝像機和機械臂的校準誤差和目標模型誤差具有較強的魯棒性。
  19. Additionally, the mutual coupling characteristic of adaptive antennas is analyzed by mom and equivalent network method, and the data model is built considering the mutual coupling of antennas arrays. the effect of mutual coupling on music algorithm is also studied, and we get a method to find the mutual coupling matrix based on music algorithm. finally, the effects of mutual coupling and rf channel imbalances on td - scdma are investigated, which will provide a reference for system design

    最後在矢量通道模型分析基礎上，深入地研究了td ? scdma系統中自適應天線與聯合檢測相結合技術，從系統矩陣和誤碼率模擬兩方面考察了自適應天線對聯合檢測性能的改善，並分析了陣列互耦和射頻通道校準誤差對td ? scdma系統上行性能的影響，為系統設計提供了依據。
  20. The best quantitative result indicated that plsr model reached a determination coefficient of 0. 999 with standard error of calibration ( sec ) of 0. 082

    在定量分析方面，以部份最小平方迥歸之定量模式進行分析，最佳分析結果顯示，判定系數可達0 . 999 ，其校正標準誤差sec為0 . 082 。
分享友人
分享到 Line

分享到臉書