校準量 的英文怎麼說

中文拼音 [jiàozhǔnliáng]
校準量 英文
calibration quantity,
  • : 校名詞1. (學校) school 2. (校官) field officer3. (姓氏) a surname
  • : Ⅰ名詞1 (標準) standard; guideline; criterion; norm 2 (目標) aim; target Ⅱ動詞1 (依據; 依照)...
  • : 量動1. (度量) measure 2. (估量) estimate; size up
  1. So it is used instead to calibrate more practical current-measuring instrument, called ammeters.

    因此,它只用於更實用的測電流的儀表安培計。
  2. Ph measurement ; technical buffer solutions, preferably for the calibration of technical measuring installations

    Ph值測.主要用於工業測設備的工業緩沖液
  3. Hydrometer for density measurement of buttermilk serum, calibrated

    的酪乳漿密度測比重計
  4. The effects of deflections are evaluated during the process of calibrating the balance.

    變形影響是在天平的過程中測的。
  5. Since there are two completely separate tracking systems there must be some collimation error or disturbance c.

    由於存在兩個完全分離的跟蹤系統,所以一定有一些誤差或干擾c。
  6. Auxiliary pressure and temperature measurements make the multifrequency phase fluorometer an ideal choice for luminescence sensor design, testing and calibration

    輔助壓力和溫度測讓多頻相位熒光計是發光探測傳感器設計、測試和的理想選擇。
  7. Hydrometry - the application of propeller - type current meters and their calibration ; german version env 14028 : 2001

    流速測.螺旋式電流計的使用及
  8. Petroleum industry. calibration identification plate for fixed tanks

    石油工業.貯罐用容鑒定牌
  9. Petroleum industry. calibration identification plate for tankers and removable tank cradles

    石油工業.油罐車和可動油罐容標識牌
  10. Industrial - process control valves - flow capacity - sizing equations for fluid flow through multistage control valves with interstage recovery

    工業過程式控制制閥.流通能力.通過有段間恢復功能的多段控制閥的流體流公式
  11. Industrial - process control valves - part 2 - 5 : flow capacity ; sizing equations for fluid flow through multistage control valves with interstage recovery

    工業過程式控制制閥.第2 - 5部分:流通能力.通過有段間恢復能力的多段控制閥門的流體流公式
  12. Industrial - process control valves - part 2 - 5 : flow capacity - sizing equations for fluid flow through multistage control valves with interstage recovery

    工業過程式控制制閥.第2 - 5部分:流通能力.通過有段間恢復能力的多段控制閥門的流體流公式
  13. It presents a new method for the system calibration in pmp. with a special calibration gauge, both the phase - height mapping and lateral coordinates calibration could be done simultaneously through only one measurement

    時需要將平面進行多次平移,每次平移都需要進行一次測,而且過程中需要保持標平面的穩定,這些特點限制了便攜式測系統的開發。
  14. Standard test method for trace impurities in monocyclic aromatic hydrocarbons by gas chromatography and external calibration

    用氣相色譜法和外部法對單環芳香烴中微雜質的標試驗方法
  15. Volumetric distribution feature of measuring coordinate errors integrating with nonrigid errors

    三坐標測機探針的誤差分析
  16. Methods for the calibration of vibration and shock transducers - primary shock calibration using laser interferometry

    振動和沖擊傳感器的方法.採用激光干涉測法的主要沖擊
  17. Flow measurement calibration facility pipe prover

    體積管式流裝置
  18. Based on the verification regulation of prt, this paper studies the temperature characteristics of prt, suggests a method of improving the accuracy of measurement and supplies the uncertainty of calibration point

    摘要分析了檢定規程對鉑電阻溫度計的要求,通過研究鉑電阻溫度計的測溫特性,提出了提高鉑電阻溫度計測精度的方法,並給出了在溫度點的測不確定度。
  19. Standard practice for rotameter calibration

    轉子流的標實施規程
  20. We have to use quite a few distance indicators because there is no single one that can measure all the distances. this is the

    利用已知而可靠度近距離天體的天尺,去校準量度更遠距離天體的天尺,是科學家常用的慣技。
分享友人