校驗系統 的英文怎麼說

中文拼音 [jiàoyànxìtǒng]
校驗系統 英文
checking system
  • 校 : 校名詞1. （學校） school 2. （校官） field officer3. （姓氏） a surname
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. The analysis of current problem in the field of indictor and the need to improve ; 2

    根據這些情況，我們提出交流指示儀表自動校驗系統裝置的研究。
  2. The principle and the mechanical structure of the air - gap inductance - type transducer are analyzed in this article, and the static parameters are calibrated. dynamic calibration is applied to air - gap inductance - type transducer which is not good in dynamic capability, to obtain the dynamic parameters of the transducer and its measuring circuit. based on the result of the dynamic calibration, the transducer and its serving circuit are modeled so that the method of how to improve the dynamic performance can be found

    本文對現有氣隙式電感傳感器在原理和機械結構上作了深入的分析，對其參數進行了靜態標定；並且針對常規電感傳感器動態響應低，不宜用於快速動態測量的缺點，引入測試系統動力學的思想，設計了一套動態校準系統，對現有傳感器進行多次動態校準，根據動態校準的實驗結果對現有傳感器建立數學模型，得到現有傳感器的動態特性；在此基礎上，根據磨床工件在線檢測的要求，設計一個硬體補償系統來提高整個測試系統的動態特性。
  3. We have advanced equipments in the world, whole set apparatus made in german, special tools used in jatta and audi vehicles, advanced testers, wrong readers, launch tester, inner peeper, advanced repairing machines, automatic lift shaft, wheel balancer and italy automatic lacquer baker, computer print reached ministry standard

    義大利全自動烤漆房，全自動電腦調漆設備，義大利全自動輪胎平衡機，全自動輪胎安拆機義大利吊裝起重設備加拿大車身校正系統汽車電能試驗器廢氣分析儀電腦故障閱讀器空調系統冷媒測漏儀abs測試儀噴射測試儀機油壓力測試儀等。
  4. Iso 1 resistance welding - welding current measurement for resistance welding - part 4 : calibration system iso 17657 - 4 : 2005

    電阻焊.電阻焊用焊接電流測量.第4部分:校驗系統
  5. The basic nuclear lab system is a complete student station designed for high school and college level nuclear science instruction

    基礎核實驗系統是一個完整的工作系統為高等院校的學生進行科學研究用。
  6. Standard practice for use of a calibration device to demonstrate the inspection capability of an interferometric laser imaging nondestructive tire inspection system

    使用校準設備驗證干涉激光成像無損輪胎檢驗系統檢驗能力的標準實施規范
  7. The non - aliasing frequency and non - ambiguous 2 - d angles is obtained by the phase characteristic of eignevalue and integral search method in this dissertation, an algorithm of spatio - temporal 2 - dspectra estimation based on 4th - order cumulants was introduced and used to realize a prototype scout, a calibration algorithm in the wide - band array system is proposed

    本文主要介紹了基於四階累積量的時-空二維譜估計演算法，並以此為基礎來實現時頻空三維偵察機；寬頻段陣列系統各種誤差參數的校正演算法，實驗系統的硬體驅動程序的開發和應用軟體的開發。
  8. Under the pattern of cyber - education, open laboratories are becoming inseparable parts which still are weak in the process of teaching. as for electric experiment category, there are many problems in common, for instance, less safe in equipment systems, less functional in instrument protection, thus forcing students to spend large quantity of time reviewing, recording, and analyzing data, while students do experiment only with less time, which have negative effect on purpose of experiment, at the same time, this does not reflect benefits that internet brings us

    然而當前大多數高校的實驗教學環節還比較薄弱，其中對電類實驗來說存在諸多共性問題，比如：實驗系統安全性差，儀表保護功能少，導致實驗器材損壞嚴重：儀表性能不穩定，零漂、溫漂現象嚴重，元器件線性度校正不夠，儀表測量精度差；學生做一次實驗要花大量時間記錄數據、整理數據、寫實驗報告，真正用在做實驗上的時間並不多，從而使實驗效率大大下降；同時也沒有充分利用校園網所帶來的便利和信息共享及互動的功能。
  9. Development of calibration system based on can bus for combined meter in automobile

    總線的汽車組合儀表校驗系統的設計
  10. Traceability is an important capability that helps you validate and verify your system

    可追蹤性的重要性在於能夠幫助你檢測和校驗系統。
  11. Liquid hydrocarbons - dynamic measurement - proving systems for volumetric meters - guide for operators of pipe provers

    液態烴.動態測量.容積式流量計校驗系統.管道校驗儀操作者指南
  12. A checksum system is used for each piece. when you specify the 4 edges correctly, it ' s border will turn from red to green

    有一個校驗系統自動對每一個方格進行檢查。當您把每個方格的顏色配置正確后，方格的邊界線將由紅色變為綠色。
  13. Nntp metrology engineer is responsible for qc equipment, equipment sheets and calibration ( chinese calibration institute ) at nntp, trained staff is able to handle calibration system according to specification

    負責qc設備，設備登記表以及校驗事宜，受訓的人員能夠根據標準處理校驗系統
  14. Finally, the paper validated five verifying means in actual statistics data and summarized the things which should be noticed, the further researches directions. key words : verifying statistics data, role, test

    最後用一些實際的統計數據對本系統進行驗證和測試，並對校驗系統的現存問題及今後的研究方向作了總結。
  15. Special investigation check : to check and recognize the overall data in different levels with the some accurate data which the investigate team has got i have developed a verifying statistics data software combined with the five methods mentioned above

    5專項調查校驗：用調查隊調查的局部準確數據對層層匯總的全面數據進行校驗識別。文中結合統計數據校驗的五種方法編制了一套統計數據校驗系統軟體。
  16. The implications of verifying statistics was discussed from the outset of the quality of statistics data, and the important meanings of designing the verifying systems of statistics data was clarified, verifying statistics data include basic verification and exact verification

    從統計數據質量研究入手，論述了統計數據校驗的含義，提出了統計數據校驗系統設計的重要現實意義。統計數據校驗分為基礎性校驗和準確性校驗。
  17. According to the study work of this paper, an automatic six - component strain gauge balance calibration system development scheme was put forwards : the system calibrates the balances in the ecs, and translates the loads to the bcs of the balances with measuring the balance ’ s position changes during the calibration

    本文根據1m高超聲速風洞氣動力試驗的總體要求，提出了採用天平校準載荷地軸系全自動加載、並通過天平空間位移測量將校準載荷換算到天平體軸系（ bcs ）的六分量天平校準系統總體研製方案，並確定了詳細的技術指標。
  18. Finally, computer aid measurement correction system is set up. the experiment is done in this system. it proves that nonstandard calibration technology is feasible and oddity point problem is avoidable

    通過此輔助測量校正系統，我們進行了實驗，驗證了網路分析儀非標準校正技術的可行性及其奇異點研究結論的正確性。
  19. The service system of local accounting includes eight aspects as follows : collecting management, accounting management, account management, statistics inquiring management, material management, customer suing treatment, checking and system management. collecting and accounting management are two important functional modes for the accounting system

    計費帳務系統從功能上劃分為採集管理、計費管理、帳務管理、統計查詢管理、資料管理、用戶申告處理、審核校驗、系統管理；採集和計費是本地計費帳務系統重要的兩個方面。
  20. Authorized by qa director, this position is responsible for plant validation system maintenance and improvement, calibration system maintenance and improvement, annual vendor audit and new vendor development audit, communicate the quality issue and follow - up supplier car to push supplier improving material quality. and also in change of organizing the leading internal audit

    在qa總監的授權下，主要負責公司現有驗證系統的維護和改進工作，負責公司現有校驗系統的維護和改進，負責供應商的年度審核和新供應商開發的審核，和供應商溝通質量問題並跟進供應商進行質量改進.並組織內部審核工作
分享友人
分享到 Line

分享到臉書