桶形 的英文怎麼說

中文拼音 [tǒngxíng]
桶形 英文
barrel field
  • 桶 : Ⅰ名詞（圓形或方形器具） barrel; bucket; commode; keg; pail; tub Ⅱ量詞（一種容量單位） barrel
  1. Romanesque _ vaulting _ desc ; romanesque churches sustained massive barrel vaults, requiring the reinforcement of the load - bearing walls in order to parry the lateral outward thrust

    羅馬式教堂延續不變的厚重桶形穹頂，需要加強承重墻以躲避向外的側向推力。
  2. To make the image height of f - theta lens in proportional to the scanning angle, it is primary to introduce barrel distortion

    本質上f - theta鏡頭通過引入桶形畸變，使得像高線性正比于掃描角。
  3. During the research on image distortion correction, the paper receives a good result on camera calibration by improving the traditional barrel distortion model, and expands the current theories on image distortion correction

    在圖像失真校正的研究中，本文對傳統的桶形失真模型進行了改進，取得了較好的校正效果，擴展了現有的圖像失真校正理論。
  4. Barrel - like target

    桶形靶子
  5. It mainly controls the transfer of the chemical from the drum container to the day tank

    主要控制將化工試劑從桶形容器移至日箱的過程。
  6. Ultimate reacting force method of the capacity calculation of bucket foundation

    桶形基礎承載力計算的極限反力法
  7. Packaging for winding wires - cylindrical barrelled delivery spools - basic dimensions

    繞組線的封裝.圓桶形輸出線軸.基本尺寸
  8. Packaging of winding wires - cylindrical barrelled delivery spools - specification for non - returnable spools made from thermoplastic material

    繞組線的封裝.第2部分:圓桶形輸出線軸.第3節:由熱塑性塑料製成的不能重復使用的繞線軸規范
  9. Packaging of winding wires. part 2 : cylindrical barreled delivery spools. section 2 : specification for returnable spools made from thermoplastic material

    繞組線的封裝.第2部分:圓桶形輸出線軸.第2節:由熱塑性材料製成的可回收使用的繞線軸規范
  10. Packaging of windings wires. part 2 : cylindrical barrelled delivery spools. section 3 : specification for non - returnable sppols made from thermplastic material

    繞組線的封裝.第2部分:圓桶形輸出線軸.第3節:由熱塑性材料製成的不能回收使用的繞線軸規范
  11. The hydraulic analysis of pump for suction penetration of bucket foundation as well as the pressure head relation between bucket cavity and pump inlet for different water depths and different pump mounting heights are described in this paper

    對桶形基礎平臺負壓沉貫過程中汲水泵機進行了初步水力分析，討論了不同水深、不同泵機安裝高度情況下，桶腔和泵機進口之間的壓頭關系。
  12. The analytic model calculating for the platform with bucket foundation

    灘海桶形基礎平臺整體模態計算
  13. Based on current forcecalculation of varying current velocity distribution and static analysis of mooting lines ' a new method of dynamic balance is proposed, which can makebfp to be vertical in submergence, and assure bfp to touch seabed in favorable position and insert into preconcerted depth successfully

    通過分析平臺沉放過程中的受力，採用動態調平的新方法，可以使平臺在沉放過程中保持垂直，保證桶形基礎以良好的初始姿態觸底並順利地插入到預定的深度。
  14. The thesis is the initial research content of the project " bucket foundation and unstability mechanism research influenced by bucket foundation on silty. sand seabed ", which is supported by the national natural science fund. it mainly carry about the research of seepage gradient in the process of suction penetration and unstability mechanism of silty sand in the bucket foundation, and it also discuss and analyze the penetration effect of bucket foundation of the different ratio size

    本文是國家自然科學基金項目「海上平臺桶形基礎及其作用下的粉質土海床失穩機制的研究」的前期研究內容，主要通過模型試驗對負壓沉貫過程的滲流梯度及其桶內粉質土的失穩機制進行研究，並探討和分析了不同比尺的桶基的沉貫效應。
  15. Survey method for the bucket foundation platform installation error

    桶形基礎平臺桶基安裝誤差檢測方法探討
  16. Limit analysis and calculation for bucket foundation embedded in soft clay based on the upper - bound theorem

    軟黏土中桶形基礎的上限法極限分析模型及其計算
  17. Structural design and analysis of shallow water bucket foundation platform

    淺海桶基平臺桶形基礎結構設計分析
  18. I looked around and noticed a very old, barrel - shaped covered basket in the corner

    我環顧四周，注意到一個非常舊的桶形的蓋住了的籃子在角落裡。
  19. Self - locking barrel nut

    桶形自鎖螺母
  20. Analysis of horizontal bear capacity and stability against sliding of bucket foundation platform

    淺海桶形基礎平臺水平承載力與抗滑穩定分析
分享友人
分享到 Line

分享到臉書