楔形接合 的英文怎麼說

中文拼音 [xiēxíngjiēgě]
楔形接合 英文
foxtail joint
  • 楔 : Ⅰ名詞1. （榫頭） wedge2. （木釘; 竹釘） pegⅡ動詞（楔） wedge
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 接合 : joint; zygosis; juncture; articulation; concrescent; nexus; coaptation; syndesis; synapsis; meet;...
  1. By calculating large quantity of examples, this text studies earthquake resistant behavior of tapered portal frame with pined bases and analyzes its natural frequency, natural period of vibration and vibration mode. by comparing interior forces of pillar top, beam end and span midpoint in two conditions that seismic action effect participates combination of forces and not when portal frame is n ' t changed, ensure conditions that combination of seismic action effect has controlling f unction during tapered portal frame design, and tapered portal frame demands anti - earthquake design

    本文通過大量算例分析，研究柱腳鉸接楔形變截面門式剛架的抗震性能，並對其自振頻率、振型進行了分析；通過比較地震作用效應參與荷載組合與不參與荷載組合兩種情況下，樑柱截面尺寸不變時，柱上端、梁端、跨中截面處的內力大小，確定在什麼情況下地震作用效應組合起控製作用，變截面門式剛架需要進行抗震設計。
  2. The ears are sutured and either tapped over the head and covered with gauze, or are taped and glued to a wedge of foam, or a styrofoam cup, or some other manner to keep the ears upright to allow for healing of the edges

    耳朵縫合，兩只耳朵在頭部上方用紗布包裹搭接或者沾在一個楔形物上，或者用一隻泡沫聚苯乙烯杯子等其他一些方式來保持耳朵在切口愈合期間豎立。
  3. Results the occlusion contact data and graph of wedge - shaped teeth defect had the features of trauma occlusion. 42. 97 % of them has the larger axial gradient degree, 96. 09 % of them has abration in different classes, 46. 29 % missing the front teeth and 57. 03 % missing the buccal teeth

    方法採用臨床物理檢查和石膏模型測量，確定楔狀缺損牙軸傾度、磨損指數、牙缺失等指標；採用計算機圖像處理技術，自行編制軟體程式及硬體系統，測試被檢光（牙合）片，分析並提取楔狀缺損牙接觸（牙合）力、面積、接觸點（牙合）應力等資料和圖形信息。
  4. Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great

    採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。
  5. The base discharge elbow shall meet the slide bracket by method of a three point, wedged engagement that is uniquely designed to match the volute flange to the stationary elbow to eliminate head losses

    排泄彎頭基座應該與滑動平臺相匹配，所採用的連接方式應該為三點楔入接合式，並專為蝸形法蘭與固定彎頭特別設計，能夠達到消除揚程損失的目的。
分享友人
分享到 Line

分享到臉書