楔形結合點 的英文怎麼說

中文拼音 [xiēxíngjiēgědiǎn]
楔形結合點 英文
wedge bond
  • 楔 : Ⅰ名詞1. （榫頭） wedge2. （木釘; 竹釘） pegⅡ動詞（楔） wedge
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 結合 : 1 （發生密切聯系; 聯合） combine; unite; integrate; link; binding; coalition; cohesion; connectio...
  1. The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation

    高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。
  2. Adhesives - determination of dynamic resistance to cleavage of high strength adhesive bonds under impact conditions - wedge impact method

    粘合劑.沖擊情況下高強度粘結點耐動態劈裂性能的測定.楔形沖擊法
  3. Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great

    採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。
分享友人
分享到 Line

分享到臉書