楔面壓力 的英文怎麼說
中文拼音 [xiēmiànyālì]
楔面壓力
英文
wedge pressure-
Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration
首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。Based on the hypothesis that the rear side of retaining wall is pitching and coarse, and the filling surface is gradient, taking viscous filling as the object of study and using the static balance method, a study has been conducted on the earth pressure on the rear side of retaining wall under the sliding wedge ' s limiting equilibrium condition, and generated a general form for active earth pressure and passive earth pressure
摘要基於擋土墻墻背俯斜、粗糙且填土表面傾斜的情況，以粘性填土為研究對象，用靜力平衡方法研究了擋土墻后滑動土楔體達到極限平衡狀態時作用於墻背的土壓力，提出了主動土壓力和被動土壓力的一般形式。Compared with those of as - sprayed ring, hardness and tension strength of area near processing face are increased by 45 % and 40 % respectively. friction mechanical performance of the ring is improved at large extent, and especially the wearing amount is merely 13 % of as - sprayed rings. after dual - direction cyclic pressing, the pore - closed state and the distributing of density and hardness are nearly identical in every part of ring. the friction mechanical property is close to that of single - direction - cyclic - press ring
靠近壓力加工面部位，硬度較沉積坯提高了45 % ，拉伸強度較沉積坯提高了40 % 。雙向楔壓后孔洞閉合、密度硬度分佈都比較均勻。單向楔壓后，用壓力加工面作為摩擦面， al - 20 % si / sicp復合材料的摩擦磨損性能得到大幅度提高，尤其磨損量為楔壓前的13 % 。Ch foam material is filled in the cavities in order to improve planar degree of shock wave driven by x - ray radiation. wedge - shaped aluminum samples are used to measure time - space streaking images of optical signals from the shock wave. and then the velocity and pressure of the shock wave is obtained. the radiation temperature is obtained by using the scaled relations between veloctiy of shock wave and radiation temperature
在腔內充ch發泡材料，提高輻射驅動沖擊波的平面性.利用楔形鋁膜測量輻射驅動沖擊波發光信號的條紋圖像，從而獲得沖擊波速度和沖擊波壓力.利用沖擊波速度與輻射溫度的定標關系，求得輻射溫度分享友人