極限平衡 的英文怎麼說

中文拼音 [jíxiànpínghéng]
極限平衡 英文
ultimate equilibrium
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 衡 : Ⅰ名詞1 （秤桿） the graduated arm of a steelyard2 （稱重量的器具） weighing apparatus3 （姓氏） a...
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. The current chinese foundation design code gbj7 - 89 use limit equilibrium theoiy with elastic soil stress distribution to give out bearing capacity design value calculating fonnula and use elastic soil model to evaluate foundation settlement. according to the above theories, code gbj7 - 89 gives the correlative terms. but these do not accord with the practical mechanism of loaded soil below the shallow foundation and the elastoplastic property of natural soil so defects exist

    我國現行規范gbj7 - 89將這兩者分開考慮，其計算地基承載力設計值的公式是根據彈性地基中應力分佈及土的極限平衡狀態理論為依據而得出的，求地基的沉降變形時則視土體為彈性，這些理論對地基及土的假設與淺基礎地基的實際工作狀態及天然土體的非線性、彈塑性存在一定的偏差。
  2. The results reveal that calculation errors can be reduced with the linear expending nodes, which can be found out by anti - inference method, decided on the limiting equilibration surface based on the advance losm method

    結果顯示，用改進一次二階矩法將線性展開點（可用反演算法求得）選在極限平衡狀態面上，可減小計算誤差。
  3. Generalized equivalent confining pressure and limited balance conditions 0f reinforced laterite

    加筋紅土的廣義等效圍壓和極限平衡條件
  4. The deformation of the waffle slab can be calcu1ated by using the tab1es of two - - way so1id s1ab. but with a changing flexural rigidity coefficient, which was very c1ose to the test va1ue in the uncracked and cracked stages

    根據試驗結果，用極限平衡法可以便捷和較為準確地求得雙向密肋樓蓋的極限平衡荷載；提出了利用雙向板表格計算雙向密肋樓蓋的變形。
  5. It analyse the stability with numerical simulation. finally, on the basis of geological estimation and analysis of the monitoring data and the numerical simulation, it conclude : ( 1 ) through the tracking investigation of the deformation phenomenon, and the study of the rock mass constructure of the slop, it determine the mode of the formation and destruction on the basis of aggregate analysis of the monitoring data

    最後，結合地質判斷、監測分析結果及數值模擬分析結果以及對典型剖面的極限平衡計算結果，得出了以下主要成果： （ 1 ）通過對「左砂」邊坡變形破壞跡象的跟蹤調研，對斜坡的巖體結構和已經發生的破壞跡象進行深入的研究分析，結合對監測資料的綜合分析，確定了「左砂」邊坡可能的變形破壞模式。
  6. Based on study above, apply the maximum equilibrium method and the block theory to analyse and evaluate the man - made slope stability. at last, the remedy measures has been presented

    在此基礎上，采剛極限平衡理論和塊體理論對工程邊坡穩定性進行分析評價，據此提出邊坡的整治建議。
  7. Combining with the research task researching on the deformation and stability of deep excavated cuts and high filled embankment of the traffic department in fujian province, based on the residual soil slope project on the project site at k15 + 183 of yong - zhang highway ( yong ' an section ), adopting non - linear theory, modern monitoring technology and numerical simulation technology, the deformation and stability of cutting cliff debris and residual soil slopes have been studied systemically and synthetically in the thesis. at the same time theory analysis, the analysis and estimate of field monitoring are taken into account in this course. main research work and working achievement are summed up as follows : ( 1 ) with the acquaintance of the trends and development about the deformation and stability of slopes at home and abroad, slopes are classified and summarized systemically

    並通過k15 + 183工點路塹土質邊坡的各類位移變形的監測成果驗證了該程序的正確性及適用性； （ 5 ）通過應用大型有限元軟體ansys模擬分析，不僅分析了其隨著開挖時間步的應力應變關系，並模擬了與實際測斜管相匹配的測斜路徑，通過對各開挖時間步的模擬計算分析，得到了與實測數據較符合的結果； （ 6 ）綜合監測分析成果和極限平衡理論計算分析成果，對k15 + 183工點路塹邊坡的原設計坡率和幾何形態進行了優化計算分析，取得了較為滿意的結果。
  8. During calculation of the ultimate flexural capacity of composite beams, it assumes steel beam, concrete board and connecter are plastic, calculates them by ultimate equilibrium method

    在組合梁受彎極限承載力計算中，認為鋼梁、混凝土板和連接件完全塑性，採用極限平衡法計算。
  9. Because of limit that invisibility and discommodious in anciently program, based on the method of limited rigid body equilibrium, using visual program language vb and connect autocad, realize plane and solid programme of abutment analysis of arch dam, provide alternation interface for designer. presently, our country constructing and will construct high 300m arch dam, it is important to judge security based on nonlinear fem analysis. basic theory of nonlinear fem analysis and its realization in ansys were studied

    針對傳統程序的存在問題，非直觀、不易操作特點，以剛體極限平衡法為基本分析方法， visualbasic作為操作平臺，結合autocad圖形軟體，完成了剛體極限平衡法二維、三維壩肩穩定分析程序設計，使之具有直觀性，可視性、易操作性，為設計人員提供了具有友好界面的工程使用軟體目前我國西部在建和將建一批300m級的高拱壩，運用有限元方法計分析拱壩穩定性、評判大壩安全度十分有必要。
  10. ( 2 ) study the 4 plastic limit equilibrium methods, such as fellenius method, bishop method, transfer coefficient method and plane linear method, and their program design

    （ 2 ）常用的4種極限平衡法：瑞典法，簡化畢肖普法，傳遞系數法和平面直線法研究並進行程序設計。
  11. Secondly, the fu yang lailong mountain slope failure was introduced. the factors influcing the slope stability were analysed and the calculated results were compared with those obtained by insitu monitoring. finally, some conclutions were obtained, which are important to engineering application

    本文結合富陽來龍山滑坡的工程實例，介紹了來龍山滑坡的概況，分析了滑坡產生的成因、滑坡要素及監測情況，並用極限平衡法和有限元法分別進行了安全系數的計算與分析，提出並驗證了自己的觀點。
  12. At last, the finite element method, the strength reduction method and limit equilibrium method, nature slopes and excavation slopes, lateral stress unloading model and axial loading model are analyzed and discussed relatively

    最後，就有限元法、強度折減法和極限平衡法，自然邊坡與挖方邊坡，圍壓卸荷應力路徑模型分析與軸向加荷應力路徑模型分析進行了比較討論。
  13. A combined neural network and genetic algorithm with solving stability safety of homogeneous slope was proposed and the finite element method is applied to analysis the progressive failure process of the slope and the maximum equilibrium theory, requests out stability safety of homogeneous slope with the smooth arc radius of difference with the difference below the level coordinate of arc peak, utilizing the neural network algorithm to establish slidng the nonlinear mapping relationship between level coordinate of arc radious and arc peak, being adapted the neural network algorithm to look for along the minimal stability safety of homogeneous slope and corresponding arc radious and arc peak

    提出了求解邊坡穩定性安全系數的神經網路與遺傳演算法。該方法採用有限元分析和極限平衡理論，求出不同的滑弧半徑和不同的弧頂水平坐標下的邊坡穩定性安全系數，利用神經網路演算法建立滑弧半徑和弧頂水平坐標與安全系數之間的非線性映射關系，採用遺傳演算法搜索邊坡的最小穩定性安全系數及相應的滑弧半徑和滑弧中心坐標。
  14. According to the geological data which was gained by exploration investigation, establishing a geological model which can reflect rock mass characteristics ; with analyzing the internal and exterior factors synthetically, the deformation and possible failure mechanism and mode of the cut slopes was confirmed which combines with stereoic projection and other techniques ; the stabilities of the 14 high slopes are estimated synthetically by applicable design codes and guidelines. with the estimate result and some other analysis methods, the rock mass mechanical parameters of slope are identified ; as a results, 14 high slopes fall into 4 categories based on rockmass characteristics and discontinuities. the stability and deformation of some typical slopes was analyzed with distinct element method by udec ; the safety factor of some dangerous slopes are calculated by rigid limiting equilibrium method for comparison

    首先著重研究影響邊坡穩定性的內在因素，主要是通過地質勘探、測量、現場觀測等手段取得研究區地質體的基礎地質資料，建立起能夠反映地質體結構特徵的地質模型;隨后綜合分析潛在的內外部影響因素，並結合赤平投影對邊坡可能的失穩模式或破壞機製作出判斷;運用已有巖體質量分類方法對沿線14個高陡邊坡穩定性進行初步的評價，並結合試驗研究、經驗判斷、工程類比等手段確定了坡體的巖體力學參數;根據穩定性初步評價結果將研究區14個高陡邊坡按開挖方式分為4大類，並利用離散元程序udec對各類典型高陡邊坡進行了穩定性計算分析;對潛在危險邊坡利用剛體極限平衡法求出了不同工況下的安全系數。
  15. In this paper, based on the analysis of the rlem of theory foundation, computing method, preference, applicability, etc, we anatomized the rlem of three self - deficiencies and six scarcities. moreover, we adopted the parallel ways of contrasting the rlem with the fem and applied it to analyzing the impact of slide block of elasticity and plasticity, slip surface of coefficient and slip bed of elasticity, plasticity upon the stability of slope and in the plain linearity slope, the plain refracted line slope and the plain arc slope. in addition, we discussed the warp of between the lem of ( sarma, janbu, order, bishop, morgenstera - price, etc ) and the fem of result and the distributing of positive stress and shear stress on the slip surface

    本文從剖析剛體極限平衡法的理論基礎、計算方法、參數選取、適用條件等方面入手，剖析了剛體極限平衡方法的3點自身缺陷和6點不足，並在此基礎上採用了剛體極限平衡法（平面滑動破壞法、 sarma法、傳遞系數法、普遍條分法、 janbu法、 bishop法、 morgenstern - price法）與大型有限元法對比研究的方法，分析研究了平面直線型滑坡、平面折線型滑坡、平面圓弧型滑坡在漸進破壞中邊坡的滑體彈塑性參數、滑麵塑性參數） 、滑床的彈塑性、以及極限平衡法無法考慮開挖應力釋放等因素對邊坡穩定性的影響與滑動面上的正應力、剪應力分佈規律、安全系數的解答的差異。
  16. The treatise elaborates some methods to make use of the slice method and limit equilibrium theory to calculate the stable safety coefficient of dam slope, and some mathematics equations, which depend on iteration of computer program to solve

    摘要本文闡述了利用「條分法極限平衡原理」計算土壩（堤）邊坡穩定安全系數的方法，並建立了藉助計算機程序迭代求解的數學方程。
  17. In this paper, explicit solution for bishop method is deduced on the base of stress distributing along the slip surface which is assumed beforehand. moreover, optimization method for slip surface is introduced in the following process. the whole process is so simple that easily mastered by engineers

    本文基於極限平衡理論，在事先假定滑面上應力分佈形式的基礎上，推導了畢肖普法的顯式解，並且在此基礎上介紹了滑弧優化方法，其方法簡單，很容易被工程人員掌握，同時也簡化了利用畢肖普法分析邊坡穩定的過程。
  18. Then the stability of typical slopes in different conditions such as servoir water level ' s ascending, slowly descending and sharply descending are evaluated and forecasted by means of the limiting balance method and the numerical simulating method ( flac )

    利用極限平衡法和數值法（ flac ）對庫區內的典型斜坡在庫水位上升、庫水位緩慢下降和庫水位驟降等不同工況條件下的穩定前景做出了合理的評價與預測。
  19. This constitutive model describes the non - associated plastic flow of granular material, and replaces the assumption that granular material complies with associated flow rule in the limit " equilibrium theory of granular material

    該本構模型反映了散體材料的非相關塑性流動，取代了散體極限平衡理論中散體材料服從相關流動法則的假定。
  20. Based on the combination of evolution strategy and limit equilibrium method, an effective global optimization method is proposed to allocate the most dangerous non - circular critical slip surface corresponding to the minimum factor of safety in slopes

    摘要將進化策略與邊坡穩定極限平衡法相結合，建立了邊坡任意形狀最危險滑裂面及相應最小安全系數的全局優化搜索方法。
分享友人
分享到 Line

分享到臉書