極限應力狀態 的英文怎麼說

中文拼音 [jíxiànyīnglìzhuàngtài]
極限應力狀態 英文
boundary state of stress
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  • 狀態 : status; state; condition; state of affairs: （病的）危險狀態 critical condition; 戰爭狀態 state o...
  1. To study the flexural behavior, ultimate bearing state and laws of internal force redistribution of prestressed concrete continuous beams cast by different construction methods, the model tests for three pieces of the continuous beams were carride out, in which three kinds of the construction methods, such as those of lowering formwork supports at one time, transferring simply - supported structure into the continuous one and casting the beam by cantilever construction, were considered

    摘要為研究不同施工方法下預應力混凝土連續梁的彎曲性能、極限受力狀態及內力重分佈規律，進行了3根連續梁模型試驗，分別考慮一次落架、簡支變連續和懸臂施工3種施工方法。
  2. On the basis of investigations into the progressive yield process and the possible failure modes of rcc gravity dams, the quasi - elasticity design limit state of the ctrtical stability criterion is proposed and the real working state of the dams designed according to the ctriterion is discussed. a check formula using the material strength reducing factor as the safety index and a simplified formula similar to against sliding stability fromula are derived. finally, the corresponding design safety factors are given by using fem calculations with various influence parameters to be taken into account

    本文在研究碾壓混凝土重力壩漸進破壞過程和可能失穩方式的基礎上，提出了以準彈性臨界作為穩定臨界準則的設計極限狀態，分析了按該準則設計的大壩的實際工作狀態，導出了以準彈性強度儲備系數為設計安全指標的審查公式以及形式與抗剪斷公式相同的簡化公式，探討了定量計算考慮各種因素影響的相應設計安全系數的合理取值，並與現行規范方法進行了比較
  3. The current chinese foundation design code gbj7 - 89 use limit equilibrium theoiy with elastic soil stress distribution to give out bearing capacity design value calculating fonnula and use elastic soil model to evaluate foundation settlement. according to the above theories, code gbj7 - 89 gives the correlative terms. but these do not accord with the practical mechanism of loaded soil below the shallow foundation and the elastoplastic property of natural soil so defects exist

    我國現行規范gbj7 - 89將這兩者分開考慮，其計算地基承載力設計值的公式是根據彈性地基中應力分佈及土的極限平衡狀態理論為依據而得出的，求地基的沉降變形時則視土體為彈性，這些理論對地基及土的假設與淺基礎地基的實際工作狀態及天然土體的非線性、彈塑性存在一定的偏差。
  4. The consequence is, when the majority of structure does n ' t enter yield habitus, but the position of belly - board has been reached the ultimate habitus, it lead to material waste of the other positions, we should pay attention to the disastrous result it will bright to us

    它帶來的後果就是當結構的大部分處于彈性狀態時，箱梁腹板處由於剪力滯效應一般最先達到強度極限狀態，導致腹板間材料的抗力沒有得到充分的使用，如不引起重視會帶來災難性後果。
  5. The equation of the structural limiting state can be expressed : z = r - s, thereinto r and s respectively are structural resistance and load response expressed with stochastic variables, we ca

    結構的極限狀態方程可以表示為： z = r ? s ，其中r和s分別為用隨機變量表示的結構的抗力和荷載響應，通過極限狀態方程就可以得出結構的失效概率，或者是用可靠指標表示的結構的可靠度。
  6. The study in the paper starts with beam distortions, and it treats the plastic deformation area as pure bending sect, rest of the beam as rigid bodies. according to different shapes of the external tendons, it divides into three structural forms familiar in projects, that is the beams with no deviator, with a deviator and with two deviators, and studies the relation between the deformation of the external prestressing tendons and that of the beams, and derives the formulas of the ultimate stress increment of external tendons. in the formulas, the ultimate angle corresponding to half of the plastic deformation area is considered as a variable parameter

    本文首先從梁極限狀態下的變形入手，將塑性鉸區看作純彎段，將塑性鉸以外的區域看作剛體，按照體外預應力筋的形狀不同，分工程中最常見的三種體外結構形式，即無轉向塊的直線型體外筋混凝土梁、具有一個轉向塊的單折線型梁和具有兩個轉向塊的雙折線型梁，研究體外預應力筋變形和梁體的變形間的關系，推導出以極限狀態下塑性鉸區之半對應的轉角為參數的計算體外預應力混凝土簡支梁以及連續梁的體外筋應力增量計算公式，並進一步求得梁的極限承載力。
  7. Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield

    摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。
  8. The stress of slag rests with the structure, physical characteristic, and heat transfer status of slag. taking no. 1 boiler of beilun thermal power plant as example, the walltube thermal stress and the destroying impact on slag are researched

    得出鍋爐大范圍變負荷運行時熱應力能夠超過渣的強度極限引起渣結構破壞的結論，渣層的熱應力主要取決于渣的結構、物理特性和傳熱狀態。
  9. Based on the results, the eccentrically braced frame has the advantage of higher initial stiffness, load - bearing and energy consume ability. through the limit state analysis principle, the limit load was calculated by assuming the same destroy pattern of braced frame as that in the experiment. comparing the theory limit load with the measured, a good agreement was founded. it shows that the limit state analysis is really a practicable way analysed the reinforced concrete frame braced with eccentric steel

    應用極限分析中的極值原理對偏心角鋼支撐鋼筋砼框架進行極限分析時，首先擬定與試驗結果相一致的結構倒塌破壞模式，然後根據虛功原理建立了結構在極限狀態時極限承載力的計算公式，從所求的權限荷載的理論值與實測值的比較來看，理論計算值與試驗的實測值基本吻合，這說明利用本文擬定的結構破壞模式對偏心角鋼支撐框架結構進行極限分析是一條可行的途徑。
  10. Thirdly, ultimate bearing capacity theory was applied in the design of asphalt pavments. ultimate state design method for asphalt pavment structures was put forward and illustrated by a specific example. difference in design thickness by method of this paper and that of specifications was compared

    再次，將極限承載力理論應用於瀝青路面設計領域，提出了瀝青路面結構極限狀態設計方法，通過具體實例來說明，並比較了按本文方法與按規范方法得出的設計厚度的差異。
  11. At last distribution functions of load modes in life service are presented. based on the resisting force model and load model, the limit state equations of rc bridge are formulated. according to the resisting force is time - dependent and vehicle load is the non - gaussian distribution, jc method is applied to calculate the time - dependent reliability index of rc bridge

    在抗力衰減模型及橋梁荷載模型的基礎上，將可靠度理論引入橋梁結構的評定中，推導出了橋梁結構耐久性極限狀態方程，並根據耐久性極限狀態方程中抗力是時間的函數，以及車輛荷載為非正態分佈的特點，應用當量正態法（ jc法）編制相應的程序計算橋梁構件的時變可靠度指標。
  12. Secondly, through the examination and observation of the structural model of the cast - in - place pre - stressed compound floor slab system, under the normal usage load, the normal usage limit - state and the failing load, we have validated the space working - feature of the structural model under variable loads, including the rigidity, the crack, failing - state, failing load and the stress variation of the pre - stressed bar, and so on

    其次，通過對該體系的結構模型在正常使用荷載、正常使用極限狀態和破壞狀態下的試驗研究，驗證了現澆預應力復合樓蓋體系模型結構在各種荷載作用下的空間工作性能，包括剛度、裂縫、破壞形態、極限承載力及預應力筋的應力變化狀態等。
  13. According to the basis relation of stress, strain and the value of limit deformation during the strengthening of concrete architecture, the derivate computing method is applied under different state of load and internal force. and it is towards difference of stress and strain of the new and old part of the strengthening structure. it is pointed out that unloading is the necessary and important method of taking advantage of effect of the strengthening structure

    本文根據混凝土結構加固中材料的基本應力? ?應變關系和極限變形值，針對加固結構新舊兩部分的應力、應變差，應用迭加原理，導出了加固結構在不同受力狀態下的承載力和內力適用設計計算方法，指出了「卸荷」是充分發揮加固結構效能的必不可少的重要手段。
  14. This thesis used along caldwell ' s direct calculation method of the ultimate strength of ship hull girders, considered the double bottom and upperwing tank to ship ultimate strength contribution, first defined the stress distribution of the whole section of the ship girders. that is : in the sagging condition, deck and side shell of nearby deck remain the ultimate bucking strength, double bottom remain the yield stress. and the other parts keep elasticity

    本文沿用caldwell等人直接計算船體極限強度的思想，考慮雙層底和頂邊水艙對船體極限強度的貢獻，首先將船體梁整體破壞時剖面應力分佈確定為：在中垂狀態下，甲板及甲板附近的舷側均屈曲，雙層底區域則均屈服，其他部分保持彈性狀態；在中拱狀態下，雙層底及之間的底舷側均屈曲，甲板及頂邊水艙區域均屈服，其他部分則保持彈性狀態。
  15. Based on the formula which is used to compute the lateral resistance of single pile deduced by wang qitong, a formula is setup whose precondition is that the pile and the lateral soil directly around the pile deform in - phase. on the basis of that the contact stress of the foundation is equal, a formula that can be used to conform the stress - ratio of the composite ground is set up, on the same time, the principles of the deformation harmony of the soil and the piles in the composite ground are also discussed. combining with results of this test, a formula which can calculate the bearing capacity that considering the effect of group piles of the composite ground is also deduced

    視攪拌樁樁體為均質彈性介質，推導了復合地基中單樁有效樁長的理論計算公式；根據王啟銅柔性樁樁側摩阻力計算公式，以樁側土與樁體協調位移為前提推導了柔性樁樁側摩阻力的計算公式；以基底接觸應力均勻分佈，樁體、樁間土均質為前提，討論了樁，土協同工作原理，從而得出復合地基樁、土荷載變形特性，以及樁、土應力比計算公式；結合本次試驗，通過計算加載時樁體與土體的荷載分擔情況以及在極限狀態下樁土承載力發揮值，提出考慮群樁效應的攪拌樁復合地基承載力計算公式。
  16. Especially, when the isocline of x is monotone decreasing in 0 < x < 1, the svstem has no limit cycle and is globally stable ; next, we construct a saddle bifurcation at the boundary equilibrium and a degenerated bogdanov - takens bifurcation at the interior equilibrium by choosing appropriate parameter values in the following two sections, where our work are based on the theory of central manifolds and normal torms. we prove that is a codimention 3 focus - type equilibrium. system ( 6. 1 ) will have two limit cycles at some appropriate bifurcation parameter values, and have homoclinic or double - homoclinic orbits at some other appropriate bifurcation parameter values ; at last, we study the qualitative properties of the system at infinite in the poincare sphere

    因為系統在（ 0 ， 0 ）點處沒有定義，這給研究其在（ 0 ， 0 ）附近的動力學性質帶來了困難，我們應用文獻[ 17 ]中關于研究非線性方程奇點的系列理論和方法，圓滿解決了這一問題，給出了第一象限內當t +或t -時，在全參數狀態下系統的軌線趨于（ 0 ， 0 ）點的所有可能情況，其相圖也得以描繪；並且，系統不存在極限環的幾個充分條件我們也予以列出，當x的等傾線在0 x 1范圍內遞減時，系統不存在極限環，全局漸近穩定；然後，我們以中心流形定理和正規型方法為主要工具，巧妙選擇參數，分別構造了一個余維2的鞍點分岔和一個余維3退化bogdanov - takens分岔，證明了平衡點是余維3的焦點型平衡點，存在參數， m ，的值使得系統（ 6 . 1 ）有兩個極限環，還存在參數， m ，的另外值使得系統（ 6 . 1 ）有同宿軌或雙同宿軌。
  17. Boundary state of stress

    極限應力狀態
  18. As it is only a kind of ideal state to set up unified regulation institution of world merger at present, the regulation institution of enterprises merger of our country should be defined its overseas force, and we should actively participate in international cooperation, seek to solve enterprises merger through multilateral way of agreem

    鑒于目前建立統一的國際合併規制制度只是一種理想狀態，我國企業合併規制制度應明確其域外效力，並積極主動地參與國際合作，尋求通過多邊協議的方式解決對我國國內市場競爭產生影響的企業合併引起的限制競爭的問題。
  19. Bearing capacity and displacement are two main problems in the application of geotechnical engineering. based on a series of pull - out tests using three kinds of paper and a sort of window screening as geogrid, twenty - seven in limit and several in working - stress geogrid - reinforced slope model tests designed through orthogonal principle have been conducted to have obtained the relationship between the bearing capacity and four factors ( i. e. reinforcement, angle of reinforced slope, the designed - length of reinforcement and the distance between layers of reinforcement ). the law of slope lateral ( horizontal ) displacement versus to the height of slope vary with external - load was derived from the model test data, and the main factor affecting the lateral and vertical displacement of geogrid - reinforced slope was obtained through analysis

    承載力（強度）和變形是巖土工程應用領域的兩大主要問題，本文以紙和窗紗布模擬加筋土邊坡的土工格柵，在一系列拉拔試驗的基礎上，以正交設計理論分別安排27個極限應力狀態和若干個工作應力狀態加筋土邊坡模型試驗，並以模型試驗獲得的數據為依據，採用誤差、極差及回歸分析方法，探討了加筋土邊坡承載力與筋類、筋長、層間距、坡角4因素的相關關系，獲得了在外荷載作用下加筋土邊坡的側向位移隨坡高的變化規律（並進行了定性解釋）和坡頂的豎向位移特性，並分析其主要控制因素。
  20. In view of the fault existing in the method of limiting equlibrium condition for distinguishing soil mass stress state, this paper gives a simple and direct " " method based on the mohr ' s circle, which can be used in calculating soil mass stress state

    摘要本文根據以往採用極限平衡條件式來判斷土體應力狀態所存在的問題，應用摩爾圈原理，從實用出發，推導出一個既簡便又直觀的" "應用計演算法，供判斷土體應力狀態時使用，此法具有概念清楚，使用簡明直觀等特點。
分享友人
分享到 Line

分享到臉書