槽型形變 的英文怎麼說

Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義

The verification results show that the model can simulate well the tidal levels, current velocities, sediment concentration, bed load transport, diversion ratio in the bifurcation section, topographic change of the north and south channels, as well as sudden siltation caused by typhoons

大量實測資料驗證表明，該數學模型可以較好地模擬長江口地區的潮位、流速、流向、含沙量、底沙、分流比、南北槽地形變化和臺風暴潮造成的航道驟淤情況。

As a result, we find that in winter when the kuroshio is cooler than the normal, at following summer, the continental cyclone deepen and the east asia monsoon strengthen, that the mid - latitude blocking high weaken and zonal circulation develop, the east asia teleconnection of " - + - " is stired up, so that subtropical high weaken and diminish, and tend to east north, tropical monsoon trough strengthen and mei - yu front weaken, and tend to north, meanwhile south asia high weaken and diminish, and tend to eastvnorth, is easy to form eastern region type

結果發現當黑潮海溫冷異常時，後期夏季大陸熱低壓加深，東亞夏季風偏強。中緯度阻塞高壓減弱，東亞地區緯向環流發展，在東亞-西太平洋地區激發「 - + - 」的東亞遙相關型，從而西太平洋副高強度偏弱，面積偏小，位置偏東、偏北，東亞梅雨鋒也偏弱，季風槽則變強，位置偏北。同時南亞高壓偏弱，位置偏北、偏東，易形成東部型。

Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively

本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。

In addition according to the comparison of typical floods the impact of floodplain morphology to the flood propagation was studied. no continuous water body in main channel and floodplain and the change of floodplain morphology and the increased flood detention capacity caused the time of flood propagation increasing and the flood types changing in abnormally

同時通過對典型洪水的對比分析，研究了灘地邊界條件對洪水運行的影響，認識到由於主槽與灘地水體不連續以及灘地地形的改變，灘地蓄洪能力增大，造成洪水傳播時間增長和洪峰峰型的異常變化。

Flute type deformation

槽型形變

According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。

In this part, the first work is pretreatment of a numerical model, including creating calculating grids automatically, improvement of the linear boundary technique and so on. the second work is to estimate the siltation of a basin or channel by liu ' s equation. the third work is to build an edbms ( engineering data base management system ) for the result of mathematical model

其中主要的工作是：其中主要的工作一是數學模型的前處理，計算網格自動生成，線邊界法的優化；二是應用劉家駒公式在長江口深水航道治理工程地理信息系統的支持下實現港池、航槽開挖的實時回淤估算；三是將計算成果形成gis管理和支持下的工程數據庫系統（ engineeringdatabasemanagementsystem ） ，同時嘗試解決時間序列數據如地形沖淤變化，潮位、流速過程的分析、查詢和顯示問題，並實現實時、互動的動態演示及三維可視化。

Abstract : variations of flow pattern, flow velocity in deep poo l and side bar, mainstream thread, and water surface, caused by excavation project, are investigated by two - dimensional mathematical model in an orthogonal curvili near coordinate system. the change of bed - load transport rate, and redeposition r ate are predicted. the influences of the excavation project on navigation are ana lyzed. grid - type and flat - type excavation alternatives are proposed and discuss ed

文摘:採用正交曲線坐標系下的河道平面二維數學模型，研究了嘉陵江何家磧邊灘采砂后河道流勢、流態、灘槽流速、主流位置、水面高程及比降的變化規律，預測了采砂方案完成後卵石推移質輸沙率變化及其對航道的影響，並對格形開挖和平整開挖方案進行了比較分析

Based on the hydrodynamic theory, the riverbed deformation process of all reservoir area during long duration is investigated by using of computer numerical simulation. in the meantime, based on one dimensional sediment model, the simulation of the longitudinal scouring and sedimentation and lateral deformation in reservoir tidal flat and mainstream are researched. the quasi - two dimensional sediment numerical model forecasting longitudinal scouring and sedimentation and lateral deformation in reservoir and river are established

應用水動力學理論，以計算機數值模擬為手段，主要考慮長歷時全庫段的河床變形過程，在一維泥沙數學模型基礎上，同時考慮水庫灘槽縱向沖淤和橫向變形的模擬，著重建立可以預測水庫及河道縱向沖淤及橫向變形的準二維泥沙數學模型。

A nonlinear numerical model for wave transformation is established in time domain based on integral equation transformed from two dimensional laplace equation. then the model is applied to compute the linear wave and nonlinear wave deformation in offshore flow field. a new 0 - 1 combined bem ( boundary element method ) is adopted in this thesis to avoid computational errors accumulated with time steps

本文以波動勢函數的laplace方程的green積分轉換得到的邊界積分方程為基本控制方程，建立了一種新的時域內波浪變形計算的數值模型，籍此對非線性波浪在結構物周圍的波浪形態進行了數值模擬，並通過數值造波水槽內的波浪試驗對數值模擬結果進行檢驗。

Being utilized in the wave propagation for nan gang of yangtze river estuary, this model can give good results of numerical simulation by effectively reflecting the influence of complicated topography which is comprised of shoal - channel spaced in between

將模型應用於地形復雜變化的長江口南港水域內波浪場的計算，計算結果說明，模型能較好地反映灘槽相間、急劇變化的地形的影響。

Based on the research about state of metal in groove, an new five zone describing model for continuous extrusion process was established to describe the process, and its analytic solution of stress calculation for each sub - zone was given

摘要在連續擠壓技術研究的基礎上，通過觀測擠壓輪槽金屬的變形形貌，提出了「五分區」的連續擠壓變形過程描述模型，構成了連續擠壓輪溝槽變形區系統、完整、準確的表徵。

The resonant three - wave model and laminar - turbulent velocity profile composed are used as a model of coherent structures in. turbulent flow. the forming and variation of turbulent coherent structures in the channel are simulated by the compact differential method with high accuracy and resolution derived in this paper

以共振三波和層-湍復合速度剖面作為湍流相干結構模型，採用文中所導出的高精度、高解析度的緊致差分方法，模擬了槽道流動在近壁區域湍流相干結構的形成和變化。

We give some useful analyses and the computer simulations for the ion etching process. compared with the atomic force microscope ( afm ) scanning photograph of the etching surface, the theoretical results prove that these simulation analyses assure the precision required by this problem, so these mathematical models are reasonable and correct. the analysis method in this paper is useful to analyze etching process, and it can also afford some valuable reference to etching technology

在本論文我們主要利用這個數學模型，對使用離子束刻蝕製作單臺階光柵的臺階與溝槽部分的表面面形隨時間的演變過程分別進行了計算機模擬分析，並通過把理論結果與在實驗中得到的刻蝕表面在原子力顯微鏡（ afm ）下拍攝的照片進行比較，結果說明這種模擬分析能夠保證對該問題分析所要求的精度，從而也證明了理論模型的合理性和正確性。

Make a comprehensive view of all study results about the flood channel, a model of formation and evolution of the flood channels was proposed. according to this model, not all flood channels formed by ebb channels divided by sand spit develop toward death, some of them may be keeping the current situation or transform to the reserve channel with the change of runoff and sediment concentration from upper reach

用gis方法計算1861 - 2002年新橋水道區域的沖淤變化，可定量表達漲潮槽在不同時間尺度形成演化規律，結合漲潮槽巖芯沉積物垂向的沉積特性變化，可闡明漲潮槽的形成機理與演化過程，並提出不同種類型漲潮槽的形成演化模式。