模擬分佈 的英文怎麼說

中文拼音 [mónǐfēnbù]
模擬分佈 英文
analog distribution
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 擬 : 動詞1. （設計; 起草） draw up; draft 2. （打算; 想要） intend; plan 3. （模仿） imitate
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 模擬 : imitate; simulate; analog; analogy; imitation; simulation模擬艙 boilerplate; 模擬電路 [電學] circ...
  1. The approximation analysis result of band dipole model is obtained on the basis of the theory of mfl. the electromagnetic distribution feature of the defect in the steel panel is studied by means of simulation. the leakage magnetic distribution of the two defects and four defects plural and the defects in the column differently in the width are also assayed. conclusions that factors affecting flaw magnetic leakage to the panel also affect the column and magnetic leakage bx should be the feature of the flaw identification to several flaws are drawn

    在對漏磁檢測原理進行詳細介紹的基礎上，得出了帶偶極子模型的近似解析解，並以有限元數值模擬分析為主要手段，以鋼板上缺陷為對象，分析了各因素對缺陷漏磁場產生影響的不同規律，同時模擬分析了板上平行的兩條裂紋，四條裂紋以及柱體上寬度不同時的裂紋的漏磁場分佈特徵，得出結論:影響板上缺陷漏磁場的諸因素會對柱體上缺陷漏磁場產生同樣的影響;對于多條裂紋，宜用漏磁分量bx作為缺陷識別的特徵量。
  2. The research object of this thesis is a chip - array that is fixed on one of printed circuit boards ( pcb ), which are located in a forced air field ( forced convection ) in an electronic case ; and from the essential equations of airflow we can deduce the mathematical model of the turbulent flow ; then we can establish the finite element algorithm and apply the fe software to work out the equations of turbulent flow, finally we can use the software to display and analyse the field of flow and temperature

    本文以處于強迫空氣對流流場中的某pcb板及其板上的電子元件陣列作為研究對象，推導了紊流流場的數學模型，並建立了相應的有限元求解格式，應用有限元法分析軟體對該系統的紊流流場和溫度場進行了模擬分析：解算出pcb板上各電子元件的溫度分佈；並提出了用於求解系統風道特性曲線的cfd方法。
  3. In this article, according to heat conduction theory, elastic creep theory and finite element theory, the temperature field and creep stress field in the arch dam during construction and operation are simulated and analyzed by means of three dimensional finite element relocating mesh method, and the distribution law of the temperature field and creep stress field in the arch dam during construction and operation are systematically studied, and according to the construction process of concrete arch dam, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress in the arch dam are also considered

    論文根據熱傳導理論、彈性徐變理論及有限元理論，用三維有限元浮動網格法對拱壩施工期和運行期溫度場、徐變應力場進行了全過程模擬分析，較為系統的研究了混凝土拱壩施工期和運行期溫度場、徐變應力場的分佈規律，在分析中按照混凝土拱壩施工過程，考慮了混凝土分層澆築、施工間隙時間、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度應力的影響。
  4. Finally, a correlative equation about bearing capacity of this structural member under bending and torsion is deduced, which may provide design of such structural members a valuable reference. to imitate centrifugal concrete - filled steel tubes used in real structures, three - dimension models are built up by using finite element method. the resistance performance of this structure under complex loads is studied

    利用三維有限元模擬分析方法對離心鋼管混凝土在彎扭組合作用、彎壓組合作用、壓扭組合作用下的構件彈性應力分佈進行了研究，分析了離心鋼管混凝土構件在組合作用下的工作機理和承載力的相關關系。
  5. Based on nonlinear finite element theory, stress and deformation behaviors are analyzed after ground stabilization and foundation pit reinforcement with deep mixing method. by comparison of the conditions of treatment and non - treatment of two examples respectively, the results indicate that the match ratio scheme used for deep mixing method is more ideal when soft clay is stabilized in this area of fuzhou in the thesis. this scheme not only can fully utilize industrial waste material, but also can economize construction cost

    對于加固土的工程特性，本文以非線性有限元理論為基礎，模擬分析水泥攪拌樁加固地基和基坑支護加固的應力和變形情況；通過兩個例子分別在有處理和無處理情況下的對比，利用固化劑最佳摻入比來設計地基處理方案，並運用非線性有限元方法計算出土體內大小主應力的分佈情況以及變形情況，結果表明本文所得出的配合比方案用於深層攪拌樁法來對福州地區軟粘土進行地基加固時還是比較理想的，這樣不僅充分利用工業廢料，還可節約工程造價。
  6. And the results of calculation and numerical simulation indicate, without increasing the intrinsic collector - junction area of power devices, collector - combed structure helps to raise the intrinsic heat - dissipating area and base ' s perimeter, improve heat - dissipating method of each cell of the chip, enhance the distribution uniformity of junction temperature and current of each cell of the chip, reduce the thermal resistance and raise the dissipation power pd and output power p0, fairly well relax the contradiction among frequency, out - put power and dissipation power of the devices, and further improve the devices " property against second breakdown

    而計算分析和二維數值模擬分析結果表明：梳狀集電結（基區）結構在不增加器件本徵集電結面積的條件下，增大了器件的本徵散熱面積和基區周長，改進了每個子器件單元內的散熱方式，提高了單元內結溫和電流分佈的均勻性，降低了器件的熱阻，增大了器件的耗散功率和輸出功率，較好地緩解了目前傳統結構中頻率與功率、功耗的矛盾，並有利於改善器件抗二次擊穿的性能。
  7. The authors describe the modelling of a railway steel truss bridge with long - span in order to analyse the detailed distribution of stress for members and nodal plates in main truss, the detailed deformation and stress distribution due to frame effect on transversal bracing plane in truss bridge, and the detailed distribution of stress in important parts of the steel plate girder bridge with initially transversal deformation by using sseb in this article

    本文建立大跨鐵路鋼桁梁橋和鋼板梁橋全橋結構模擬分析數學模型，說明了鋼桁梁橋桿件和節點板詳細應力分佈、平面框架詳細變形與應力分佈和有變形缺陷鋼板梁橋重要部位應力的模擬分析結果等問題。
  8. ( 2 ). according to the system indices and requirements together with the technology characteristic, it researches the capture possibility of apt capturing system. then it introduces the common scan methods, such as raster, spiral, raster spiral, rose and lissajo. ( 3 ). it makes a detailed simulation analysis of the raster and spiral scan, analyze the connection between capture probability, capture time, system index at different capture resolution angle, capture range, vibration angle extent and terminal location distributing mean square deviation

    其中對幾個關鍵部分進行了詳細分析:計算了目標角反射器的激光雷達散射截面（ lrcs ）值，研究了qd與ccd對目標位置角度的計算方法和空間解析度; （ 2 ）根據系統指標和要求並結合現有國內技術特點研究了apt捕獲系統掃描的捕獲概率問題，然後分析了幾種常見的掃描方式:矩形（ raster ）掃描、螺旋（ spiral ）掃描，矩形螺旋（ rasterspiral ）掃描，玫瑰形（ rose ）掃描以及李薩如形（ lissajo ）掃描; （ 3 ）對分行掃描和螺旋掃描進行了詳細的模擬分析，分析了它們在不同捕獲分辨角、捕獲范圍、振動角振幅和終端位置分佈均方差時的捕獲概率、捕獲時間與系統常數之間的關系。
  9. The rule of obstruction to the distributing of stress and strain of the slope is influenced by different number of the cranny

    對不同維數的結構面模擬分析比較，得出了結構面維數對應力應變分佈的影響規律。
  10. In this paper, we begin with actual products designs and then combine the real conditions. on condition that technique conditions requirements were satisfied, by adopting electromagnetic field numerical analysis and experimental research, the electric field distribution inter - phase and to ground of 12kv metalclad withdraw switchgear vacuum circuit breaker is described accurately. the electric field distribution and movement in different conditions are also confirmed

    本文從實際產品設計入手，結合現實情況，在滿足技術條件要求的基礎上，通過採用電磁場的數值模擬分析及實驗研究，準確地描述了12kv配電系統中置櫃真空斷路器相間及對地全場域電場分佈情況，確定了中置櫃在不同情況下的電場分佈、變化情況，通過理論的計算和分析，對產品的絕緣進行了校核與驗證，通過多種方法的比較，進而得到合理的布置結構和達到最佳的絕緣配合，為實際產品的開發和設計提供了理論依據。
  11. In this article, according to heat conduction theory and finite element theory, the temperature field in the arch dam during construction and operation are simulated and analyzed by means of three dimensional finite element relocating mesh method, and the distribution law of the temperature field in the arch dam during construction and operation are systematically studied, and according to the construction process of concrete arch dam, the effect of lamination placement, construction interval, thermal insulation change, surrounding temperature change and water storage on temperature field in the arch dam are also considered

    論文根據熱傳導理論及有限元理論，用三維有限元浮動網格法對施工期和運行期溫度場進行了全過程模擬分析，較為系統的研究了混凝土拱壩施工期和運行期溫度場分佈規律，在分析中按照混凝土拱壩施工過程，考慮了混凝土分層澆築、施工間隙時間、絕熱溫升過程及壩體材料分區、水庫分期蓄水和環境溫度變化等因素對壩體溫度場的影響。
  12. Several feasible boundary conditions of thermal environment computations are provided. numerical simulation of thermal environment in that residential district is carried out depending on theoretical studies, wind environment simulations and thermal environment testing mentioned above. distributions of wind velocity, pressure, turbulence and temperature in two different periods are investigated and analyzed, and feasibility of thermal environment numerical simulation is proved by comparison of temperature and velocity values between testing and simulation in some tested spots

    提出幾種可行的熱計算邊界條件，在上述基礎理論研究、風環境模擬計算、熱環境測試等基礎之上對住宅小區熱環境進行了數值模擬，分析了兩種時段內風場、壓力場、湍流場及熱場分佈，並比較了部分地點溫度和風速測試值與計算結果的差異，論證了熱環境數值模擬的可行性。
  13. Based on the analyses of the physical and mechanical properties of ore / rock and the behavior of ground stress field in the deep deposit of fankou lead - zinc mine, the authors researched the unloading measures to prevent and control rock burst in mining the deep deposit, and carried out numerical simulations of the stress distribution under different unloading mining situations by means of 3 - d elastic - plastic finite element program, so as to give decision - making basis for controlling rock burst in exploiting the deep deposit of fankou lead - zinc mine

    根據凡口鉛鋅礦深部礦巖體的物理力學性質及地應力場特性，對凡口礦深部礦床開採的巖爆防治措施進行了研究，並應用三維彈塑性有限元程序對各種防治措施引起的應力分佈進行了數值模擬分析，以期為凡口鉛鋅礦深部礦床開採的巖爆控制提供決策依據。
  14. Secondly, in view of the limitation and shortage of traditional simulation of finite element approaches for bolt, a new composite grouted bolt element including nonlinear contacting relation will be built based on the above study of the mechanics mechanism of fully grouted bolt. then, an elastic - plastic finite element program will be developed for the analyses of tunnel stability, in which the composite grouted bolt element and nonlinear finite element analysis method will be used ; the patterns and the affect of main design parameters on the support effect of bolt will be analysed using the program, and conclusions of guidance importance for tunnel support design will be drawn. finally, simulation compution for the excavation and support of a highway tunnel will be made out using the above production, and the method of application of the program will be discussed ; analysis of the deformation, stress and distribution of plastic range will be done, and rational support plan will be worked out, which is of guidance importance for tunnel support design and the thery and technique of fully grouted bolt used in tunneling will be perfected further

    首先，本文在綜合分析隧道穩定性影響因素及失穩破壞模式的基礎上，對全長粘結式砂漿錨桿作用力學機理進行了深入研究，為全長粘結式砂漿錨桿的有限元模擬分析奠定了基礎;其次，針對傳統錨桿有限元模擬方法的局限性與不足，在上述全長粘結式砂漿錨桿作用力學機理研究基礎上，建立出能反映界面非線性粘結的新型復合砂漿錨桿有限單元模型;然後，運用上述復合砂漿錨桿單元模型，引進非線性有限元分析手段，開發了隧道支護穩定性分析的有限元程序，並就全長粘結式砂漿錨桿的型式與設計參數對支護效果的影響進行了深入探討，得到了對隧道支護設計具有指導意義的結論;最後，運用本文研究成果對某公路隧道工程實例進行了開挖與支護的模擬計算，探討了其應用方法，並就隧道變形與應力及塑性區分佈規律進行了分析，從而提出了合理的支護方案，為隧道支護設計提供了參考依據，完善了隧道全長粘結式砂漿錨桿支護的理論與方法。
  15. 2 ) the inductance transducer used to identify large wear particle is developed. the analytical theory of wear particle and detection windings are expatiated and inner magnetic distribution of inductance transducer is discussed, the geometry parameters are optimized by using genetic algorithm, and the finite element analysis method is used in the designing

    2 ）研製了識別大磨損顆粒的材質和測定其粒度的電感傳感器，闡述了磨損顆粒與檢測線圈的解析關系，探討了傳感器的理論基礎，分析了電感式檢測傳感器內部的磁場分佈，並應用遺傳演算法優化了傳感器幾何參數，最後進行了有限元模擬分析。
  16. In order to solve it radically, making power assembly of bj1036e2f1 light truck the research object and through dynamic simulation analysis of power assembly, this thesis obtains the distribution rules of forces of the bolts linking three shells mentioned above and the relation between forces of the bolts and rotate speed of engine. after finite element mode analysis of these three shells, inherent frequency and vibration model of shell of power assembly are gained, and thus its dynamic character is realized. based on computer simulation analysis, experimental model of power assembly is acquired by vibration test and strength test of shell of power assembly, and the relation of forces of the shell and rotate speed of engine and imbalanced mass of rotate components is studied

    為了從根本上解決該問題，本論文以bj1036e2f1輕卡動力總成為研究對象，通過動力總成的動力學模擬分析，找出了三殼之間聯接螺栓受力的分佈規律和螺栓受力與發動機轉速的關系；通過三殼的有限元模態分析，得到了動力總成殼體的固有頻率與振型，從而了解了動力總成殼體的動態特性；在計算機模擬分析的基礎上，通過動力總成殼體的振動測試和強度測試，得出了動力總成的試驗模態，並研究了殼體受力與發動機轉速和旋轉部件不平衡質量的關系。
  17. On the basis of the result studied, three categories flaws easily turning up in the common whorl attachment are assayed by way of simulation. the result of experimental measurement verify all the conclusion from fem numerical simulation analysis 。 based on the study of the rationale of the ac - mfl, it primarily simulation studied the common whorl attachment in our country. the experimentation results go along with the simulation analysis

    螺紋構件可以看作是柱體上緊挨的多條裂紋的組合，以上述內容為基礎，以ansys模擬軟體為手段對普通螺紋構件中極易出現的三種裂紋情況（螺桿接合部的缺陷，螺紋區的缺陷，螺紋尾部的缺陷）進行了建模模擬，得出了三種不同情況下磁場分佈特徵，實驗驗證了模擬分析的正確性。
  18. The fatigue accumulation damage of the component has something to do with its model, different model causes different damage speed on the component which will show different magnetic memory characters. the paper build the mathematics model of wave shape of orders con - wave and accumulation damage distribution on several boundary conditions, combining theory deducing, simulation analysis and experiment validation, deducing the relation among fatigue accumulation damage degree, damage speed and magnetic memory characteristic parameters

    振動構件疲勞累積損傷與振型有關，不同振型引起的損傷速率不同，具有不同的磁記憶特徵。本文將理論推導、模擬分析和實驗驗證相結合，建立多種邊界條件下的各階諧波波形與累積損傷分佈的數學模型，推導疲勞累積損傷度、損傷速率與磁記憶特徵參量的關系，並利用模擬試驗系統驗證和完善，實現利用磁記憶方法對這類累積損傷構件進行早期診斷的目的。
  19. A predigested car model and a reasonable bridge model were presented after the bridge structures and the colliding characters were analyzed. the stress and the displacement of the concrete, bar, pre - stress bar changing with time were presented. the stress of the whole bridge at the time of the contact and the deformation of the whole bridge at the end of the contact are obtained

    採用美國ansys公司的有限元軟體ansys ls - dyna對碰撞過程進行數值模擬分析，得到了撞擊點附近混凝土、普通鋼筋以及預應力鋼筋的應力及位移隨時間的變化規律，同時得到了全橋在碰撞后瞬間的應力分佈規律和碰撞結束前全橋的變形規律。
  20. Using the mm5 model to conduct investigation of numerical simulation for this case, it was basically possessed of a capability to reproduce the genesis, development and evolution of the large - scale and mesoscale weather systems

    本文以mm5模式模擬分析「雅安天漏」為代表，著重研究了不同邊界層參數化方案對雨量中心強度、雨區分佈的影響以及雅安暴雨時的緯向垂直環流結構。
分享友人
分享到 Line

分享到臉書