模擬轉接中心 的英文怎麼說

中文拼音 [mónǐzhuǎnjiēzhōngxīn]
模擬轉接中心 英文
simulated transit center
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 擬 : 動詞1. （設計; 起草） draw up; draft 2. （打算; 想要） intend; plan 3. （模仿） imitate
  • 轉 : 轉構詞成分。
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 模擬 : imitate; simulate; analog; analogy; imitation; simulation模擬艙 boilerplate; 模擬電路 [電學] circ...
  • 轉接 : change-over; throw-over; switch; transfer; transit; reset; adapter coupling; built-up connection
  1. To avoid the serious electromagnetic interferer, the analog signals are transformed to frequency pulses which are transferred to the kernel of the system. in the measure of the groove voltage, the method of float - ground is adopted to avoid the high common signal and the range switch circuit is designed to solve the conflict of the wide dynamic range and the high precision. least square curvefit is adopted to reduce the system error

    鋁電解生產現場電磁干擾非常嚴重，為此我們將需要測量的模擬信號就近轉換為頻率脈沖后再傳送到控制核心；採用浮地接入方式消除槽電壓信號中的共模成分；設計了量程自動切換電路以解決槽電壓的動態范圍寬和測量精度高的矛盾；用最小二乘法進行曲線擬和以降低測量的系統誤差。
  2. The contacting measurement method with a double probe is put forward after the detailed analysis of the state - of - the - art measuring methods of the thickness of wall. firstly, the theory - profile generatrix is built, and then the movement curve of the track of joint center is constructed, which aims at making the joint center move along the movement curve and keep the fixed sensor touching the wall. the measuring sensor examines the line in its normal direction of the interior wall all the time, the data from the sensor is the thickness value of the wall

    論文通過分析國內外變曲率回轉體壁厚測量的現狀，提出了雙測頭接觸式測量方案:通過構造理論輪廓母線，建立鉸鏈中心的運動曲線，使鉸鏈中心始終沿運動曲線運動，以保證固定觸頭與傳感器測頭的連線始終在內壁法線方向上，從而傳感器測頭所得的數值即為壁厚值，該方案經模擬測試實驗取得了預期效果。
  3. As the deformation caused by centrifugal force is beyond the small deformation range, the large deformation effect was also taken into account in the equation. two models are constructed, one is of shrouded blade and the other is of bladed disc. the static natural frequencies and dynamic frequencies ( under 3000rpm ) are calculated by the finite element method and cyclic symmetry technique

    針對葉片的結構特點，採用適應較強的三維八節點實體單元模擬葉片，建立葉片運動微分方程;葉片?輪盤系統在高速旋轉時，受到離心力作用，使葉片發生大變形，故在方程中考慮了幾何大變形的問題;為研究葉根輪緣之間的接觸狀態，建立了考慮葉根?輪緣接觸的有限元方程，利用拉格朗日增廣演算法來求解該方程，確定葉根輪緣之間的接觸面狀態。
  4. Hence, the requirements of the servo control card are getting much sophisticated. in this thesis, the research work and implementation details of a 6 axes servo control card are discussed. this card is based on the ti company ? dsp chip tms320f240 and has realized the following functions : a ) signal encoder, b ) position limit, c ) dual ram communication with cpu, d ) coordinated control e ) dia conversion

    該卡以ti公司的16位定點數字信號處理器tms320f240為核心晶元，實現6路編碼器信號輸入處理，軸限位中斷處理，通過雙埠ram與pc進行通訊，接收pc發送過來的控制指令和數據，完成插補運算、聯動運算等控制，通過d / a轉換電路，將結果轉化為模擬電壓送伺服放大器驅動電機。
  5. And the displacement control of the leaf spring center was transferred to the displacement at load point. then after the load step options configuration, the leaf spring stress circulation under cycle loadings was calculated. the model was validated by the result compare between the rigid extracted from the simulation results and the one out of the rigid test of the leaf spring

    使用加載頭和簧片的接觸行為來模擬加載狀況，並將對簧片中心的變形控制轉換為對加載點的位移約束，然後利用載荷步選項配置完成一個載荷循環，由此計算出加載階段下鋼板彈簧內部的應力循環。
分享友人
分享到 Line

分享到臉書