模焊 的英文怎麼說

中文拼音 [móhàn]
模焊 英文
die welding
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. By means of carrying out parameterization on finite element model of certain punching - welding bridge housing and through optimization analysis, this paper realized the light weighted optimization design of punching - welding bridge housing under the conditions of letting the bridge housing to satisfy the demands of perpendicular bending rigidity, the perpendicular bending strength and the perpendicular bending fatigue life

    摘要通過對某沖焊橋殼的有限元模型進行參數化，經過優化分析，使得橋殼在滿足垂直彎曲剛度、垂直彎曲強度和垂直彎曲疲勞壽命的條件下，實現了沖焊橋殼的輕量化設計。
  2. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  3. The cracking with these two types of underfill might become unstable and lead to catastrophic failure at the end. the critical length was about 12m for the assembly with no - flow underfill and 20m for the package with capillary - flow underfill at 20 ?

    模擬表明，山固化溫度冷卻到室溫時，所研究的倒裝焊封裝在填充不流動膠時晶元斷裂臨界裂紋長度為12pm ，而填充傳統底充膠時為20hm 。
  4. Most scholars believe that the arms of brass and copper alloy european metalwork were cast whole from a single mold in van eyck ' s time ; crockets were not soldered or riveted onto the main arms

    多數學者相信，在范艾克的時代，歐洲的黃銅或其他銅合金的金屬工藝中，整隻吊燈臂是從一個模子里鑄出來的；而且上面的雕飾並不是焊接或鉚接到燈臂主體上。
  5. By analyzing the optimal diffluent ratio and solder angle of the dies, the maximum stress in the body of improved dies is de - creased effectively

    對模具的分流比和焊合角進行優化並再次模擬，發現分流模的最大應力大大降低。
  6. Simulation of grain growth in the haz of stainless steel eb

    1不銹鋼焊接熱影響區晶粒生長模擬
  7. Fuzzy logic control of submerged arc welding process

    埋弧焊過程的模糊控制
  8. Available options and accessories such as ground plate, lift off protection, upper welding plate and welding gauge make the module extremely versatile and ensure a very easy installation and safe operation under rugged conditions

    可選配件有接地板吊裝保護上焊接板及焊縫檢查樣板。這些配件使模塊能用於各種用途，保證安裝方便，且在凹凸不平的情況下也能安全操作。
  9. To solve these problems, a fem preprocessing system in materials joining process has been developed in this dissertation. based on this system, a welding numerical model of a missile ’ s oil box has been established and the structure ’ s distortion rules after welding have been analyzed

    本文針對這一現狀開發了一個專門針對焊接過程數值模擬的有限元前處理系統，並應用該系統建立了某型號導彈油箱結構的焊接有限元模型，分析了該結構的焊后變形規律。
  10. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  11. Simulation of material plastic flow in aluminum alloy friction stir welding based on fluent

    的鋁合金攪拌摩擦焊流動場模擬
  12. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  13. Meixing electronics factory is major in the vacuum tube stereo power amplifier, which is located in the nanhai city ， owned a workhouse over 1300 square meter, with five plant, they are box, seal and transformer circling 、 debugging & check, we also have the machine process, such as milling machine 、 punch 、 drill press 、 electric welding 、 matrix 、 incision machine, and radio tube test machine. we have realize the product line manufacture, the monthly whole output is over 200 sets

    美星電子是一個專業製造真空管身歷聲功率放大器的加工廠，位於廣東南海市黃岐工業區，擁有廠房一千三百平方米，工廠分機箱加工、焊接組裝、變壓器繞制、煲機老化、調試檢測五個車間，機械加工設備擁有銑床、沖床、創床、鉆床、電焊、模具製作、切割等二十多臺，電子管及整機檢測調試儀器十餘臺，該廠實現了配套設備、流水作業，每月可生產膽機二百臺以上，可謂中國專業生產膽機最大規模的工廠。
  14. Our factory is established in 2004, the existing staff 80 people, workshop area 2000m2, has the production assembly line 3 and thespectrometer, the oscilloscope, the high frequency signal generator, leaks the reflectoscope reflector, the pressure resistancereflectoscope reflector, the overflow welding machine, production, thecheck - out facility and so on led lamps and lanterns simulationreflectoscope reflector

    我們廠成立於2004年，現有員工80餘人，廠房面積2000m2 ，擁有生產流水線3條及頻譜儀、示波器、高頻信號發生器、漏電測試儀、耐壓測試儀、溢流焊機、 led燈具模擬測試儀等生產、檢測設備。
  15. The company has workshops for product designing, carving, die - casting, polishing, electroplating, laser engraving, drop moulding, grinding, painting, tin soldering, brazing, silver soldering and spot welding, as well as quality test center

    公司下設產品設計、刻模、壓鑄、拋光、電鍍、激光雕刻、滴塑、磨砂、畫漆、錫焊、銅焊、銀焊、點焊車間及產品質量檢測中心。
  16. A study on quality controlling system of spot welding

    點焊質量模糊控制系統研究
  17. To validate the formulated transition element for the calculation of the hot - spot stress and stress concentration factor in the welded components by experimental results, the stress concentration factor of the experimental welded specimens carried out in the research group is calculated by using the developed plane - transition element. the calculated stress concentration factor in the two types of tested welding components agrees well with that obtained from the experimental result. and the calculated result on the tendency of hot - spot stresses agrees well with that from the measured result

    為了驗證文中構造的過渡單元模型用於分析焊接節點附近的應力集中問題的正確性和有效性，進一步又對過渡單元模型進行實驗結果驗證，採用平面過渡單元模型計算了本課題組進行的兩類焊接構件的應力集中系數，並與根據實測方法得到的應力集中系數進行了比較，計算結果與實驗測試得到的應力集中系數和相應的熱點應力變化趨勢比較吻合，為本文建立的過渡單元的實際應用提供了初步的基礎。
  18. Qishuyan locomotive & rolling stock works, situated in changzhou city, jiangsu province and founded in 1905, covers an area of 1, 760, 000 square meters, owns 4, 500 unitssets of various mechanical equipment, and possesses a comprehensive production capability of forging & casting, machining, riveting & welding, heat treatment, tooling & patterns and sophisticated measures for physical & chemical tests, metrological measurements & inspection. it is an important base for manufacturing artery dedicated diesel engine locomotives, freight wagous, heavy duty diesel engines and railway components, which have won the credit and trust from customers by their excellent quality and outsanding aftersales service and enjoy good sales throughout the country and in countries in europe and america

    公司介紹：戚墅堰機車車輛廠地處經濟發達、科技進步、風景秀麗、人傑地靈的江蘇省常州市，創建於1905年，佔地176萬平方米，擁有各類機器設備4500臺，具有鍛鑄、機加工、鉚焊、熱處理、工裝模具等綜合生產能力，以及齊全的理化試驗、計量和檢測手段，是我國鐵路干線內燃機車、貨車、大功率柴油機和鐵路配件的重要生產基地，以優質的產品和優良的服務羸得客戶信賴，產品銷售遍及全國並遠銷至歐美等國際市場。
  19. The non - uniform deformation behavours and the movement of the weld seams, the wrinkling of the workpieces and the methods to control the non - uniform deformation were investigated by adjusting the die structures, the blank holding method and the blankholding force distribution

    通過調整模具結構和壓邊方法及壓邊力分佈，對坯料不均勻變形規律及焊縫的移動規律、坯料的起皺規律及控制坯料不均勻變形的方法進行了探討研究。
  20. To avoid manual labor of chiseling - grossness, in the area of second - stage concrete construction, permanently non - removed metal molding boards nets are used as molding boards of first - stage concrete. substitution joints of reinforcing steel bars for traditional electric welding and usage of equipments for joints of reinforcing steel bars efficiently improve strength of junctions and rate of connecting reinforcing steel bars, and safety of construction and stability of quality, and greatly reduce cost. it ' s possible that three gorges project become top - ranking project in the world by study on systems engineering of high - strength concrete construction

    混凝土縫面處理採用高壓水流沖毛技術，大大提高了施工工效，減少了倉面污染；模板工程大量採用定型鋼模板施工技術，提高了壩體混凝土成型質量和工程進度；在二期混凝土施工區域，為免除人工鑿毛勞動強度，採用永久性免拆金屬模板網作為一期混凝土模板；鋼筋連接改進傳統的電焊連接方式，採用大量採用鋼筋接頭機械連接技術，有效提高了接頭強度和鋼筋連接速度，施工安全性大大加強，質量穩定性有效提高，經濟成本大大降低；三峽二期工程持續高強度混凝土施工系統工程的研究，使三峽工程成為名符其實的「世界一流工程」成為可能；三峽二期工程混凝土溫控綜合技術的應用，有效降低了壩體混凝土溫度的產生；混凝土表面處理及裂縫處理技術的應用，提高了建築物的整體性和耐久性。
分享友人
分享到 Line

分享到臉書