機械流變帶 的英文怎麼說

中文拼音 [jīxièliúbiàndài]
機械流變帶 英文
zone of mechanical flow
  • 機 : machineengine
  • 械 : 名詞1. （器械） tool; instrument 2. （武器） weapon 3. [書面語] （枷和鐐銬之類的刑具） fetters, shackles, etc
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 機械 : 1. （利用力學原理組成的各種裝置） machinery; machine; mechanism 2. （死板; 刻板） mechanical; inflexible; rigid
  1. Woven wire mesh series : stainless steel wire mesh, brass wire mesh, copper wire mesh, phosphor bronze wire mesh, barbecue grill mesh, crimped wire mesh, low carbon steel wire mesh, mild steel wire mesh, black wire cloth, window screening netting, vibrating sieving mesh, filter for gas and liquid, conveyer belt, chain link fence, galvanized square wire mesh, hexagonal wire mesh

    此網帶由雙股右螺旋或由雙股左螺旋盤條與一根串條連接而成，網帶拼接方便，網眼一般小於單股加強編織的網眼，編織牢固，不易變形，維修方便。能用於高溫的自動流水線，輸送重物，機械工業上零件的熱處理，各種較大物品的烘乾。
  2. In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology

    為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。
  3. Power separating, hydraulic - mechanic drive, single stage torque converter is used in sd8 elevale sprocket bulldozer

    Sd8高驅動履帶推土機採用輸出端外分流液力機械傳動單級變矩器。
  4. On the other hand, the hydraulic performance of the hole, including flow rate coefficient and uniformity of flow rate, have been tested as standards to evaluate the quality of holes punched by laser drilling machine with much better results than that punched by mechanical drilling machine. the shape of holes taken by a microscope photograph can also give detail and well explanations for this test results

    對噴孔水力學性能的試驗研究表明，本文提出的用噴孔水力學性能指標（流量系數和流量變異系數）來評價微噴帶激光打孔機質量的方法是可行的，並證明微噴帶激光打孔機的質量明顯優于機械打孔的質量，用顯微鏡觀察噴孔的形狀的照片也同樣證明了這一點。
分享友人
分享到 Line

分享到臉書