機軸轉數表 的英文怎麼說
中文拼音 [jīzhóuzhuǎnshǔbiǎo]
機軸轉數表
英文
counter engine-
Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading
文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點Under the assumption that the inner surface of stator sleeve and outer surface of rotor are smooth, taking the fact into account that the temperature of stator sleeve of evaporation cooling motor keeps almost the same, horizontal evaporation cooling motor is simplified as a physical model of two coaxial sleeves, with outer sleeve ( the stator ) holds still and keep at constant temperature and inner sleeve ( the rotor ) is rotating and heated
本文通過數值和實驗手段研究了臥式蒸發冷卻電機楔形氣隙中的流體流動、傳熱現象。本文在定子套筒和轉子表面光滑的假設下，針對蒸發冷卻電機定子套筒壁面基本恆溫的特點，將實際蒸發冷卻電機簡化為同軸套筒內筒加熱旋轉、外簡靜止定溫的物理模型。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義Engine crank tachometer provide vtec control function
發動機曲軸轉數表提供vtec控制功能。The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。In order to investigate the unsteady flow frequency domain performances of an axial flow compressor at different mass flow, rotating speed and blade row spacing, plus inlet flow distortion, and considering aerodynamic characteristics and stability of the compressor, the low speed research compressor ( lsc ) at college of energy and power in nuaa is used to carry out the experiment studies. a large amount of test data has been gained through dynamic pressure transducers embedded in the stator blades at the tip, middle and hub section, then fast fourier transform algorithm ( fft ) is applied to calculate the frequency data
為探討軸流壓氣機在工作流量、工作轉速及動?靜葉排軸向間距變化時的葉片排流場非定常頻譜特性變化規律，並耦合進氣畸變的影響，同時與壓氣機氣動性能和氣動穩定性相關聯，作者利用南京航空航天大學能源與動力學院的低速大尺寸軸流壓氣機（ lsc ）試驗器，採取在靜子葉片表面埋入動態壓力傳感器的實驗方法，對葉尖、葉中和葉根三個截面的動態壓力進行了測量，獲得了大量的可靠的實驗數據。For getting the runner characteristics more correctly, researching the representation of runner characteristics of the kaplan turbine in this paper, and using this method of modifying runner characteristics to calculate the transient of hydraulic power station. improving the calculating model of the axial thrust in the kaplan turbine ' s transient. base on the theory of screw propeller without any boundary, using the theory of screw propeller with pipe, and the formula to calculate the dynamic axial thrust during transient is developed
本文對轉槳機組在過渡過程中的槳葉劃水產生水推力的數學模型進行了改進，在原來使用無邊界螺旋槳進行等效的基礎上，使用了導管螺旋槳對轉槳機組中的槳葉劃水進行等效，並且比較詳細的分析了影響轉槳機組軸向水推力的各個因素，以及給出了動態計算軸向水推力的公式，通過計算表明，使用改進后的動態水推力計算模型得到的結果能較好的反應實測的動態軸向水推力。The paper makes simulation for each type of electro - hydraulic regulating system of turbine. the results of simulation show that for the francis and kaplan turbines the contradiction between regulation time and pressure increasing can be solved by logical chosen of feedback adjustment coefficient and control cost - weighting matrix. for tublar turbine the dynamic matrix pi control scheme can effectively solves the difficulty of speed stabling of this type turbine
本文對各種機組調節系統進行模擬，結果表明，對于混流式和軸流轉漿式機組，通過反饋校正系數和控制權矩陣的正確選擇，可以解決調節時間和水擊壓力上升的矛盾；對于貫流式機組，提出了動態矩陣pi控制方案，可以較好的解決此類機組轉速難以穩定的問題。It is very difficult to analyze flame radiation in the cylinder of a diesel engine by theoretical method since flame radiation is a function of many parameters, such as the combustion process, the geometrical description of the chamber, the soot formation and oxidation processes, the soot radiant temperature and soot absorption coefficient. the radiant property of the flame in a cylinder is dependent on the combustion process. but the thermodynamic state of real engine cycles can be analyzed from the pressure - volume diagrams in the cylinder. thus a new thermodynamic computational model is set up for the flame radiation in the cylinder of a diesel engine based on the indirect relationship between the flame radiation and the pressure - volume diagram of the combustion process in this paper. the flame radiant heat flux in the cylinder of a di diesel engine is calculated with the variation of crank angle by this model. compared with measured values, the result of the computational values shows the model is available to represent the effects of flame radiation
柴油機缸內的火焰輻射受諸多因素的影響，用理論分析法來確定它是相當困難的，由於柴油機缸內火焰輻射特性依賴于缸內的燃燒過程，而燃燒過程中的實際熱力狀態又可用示功圖來分析，因此藉助於火焰輻射與缸內熱力參數之間的這種間接關系，建立了一種計算柴油機缸內火焰輻射傳熱的新模型，利用該模型對一臺直噴柴油機缸內火焰輻射熱流量隨曲軸轉角的變化情況進行了計算，將計算結果與實測結果進行了比較，表明該模型能較好預測缸內火焰輻射傳熱量。Abstract : it proposes a model for shaft centerline measurement and winding level, gives the coordinates transformation formula of measured data, and develops the program diagram for centerline measurement of wind - shaft
文摘:提出了一種便於微機處理的軸線的空間解析表達方法以及軸線彎曲程度的表示方法，給出了軸線測量數據獲取方法與坐標轉換公式，提出了零件軸線彎曲時精密測量的一般步驟。Piaget has gone from rotary research to jewelry watch - making, mechanical timepieces to quartz design, a workshop with only six craftsmen to a factory with more than two hundred workers, but still the company piaget strives for perfection, a principle that drove its founder, george, over a hundred years ago
從齒輪研究到鉆石軸承表製作，從機械鐘表到石英鐘表，從只有六名工匠的作坊到擁有二百多名工人的工廠，伯爵表廠雖然歷經無數轉變，但卻仍然精益求精，美更求美，這也正是百余年前激勵其創始人喬治向前的一條原則。分享友人