機電式調整器 的英文怎麼說

中文拼音 [jīdiànshìdiàozhěngqì]
機電式調整器 英文
electromechanical appliance
  • 機 : machineengine
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 機電 : electromechanical機電設備 electromechanical equipment; electromechanical device
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. In this dissertation, through computer simulation, the problems of modeling, control and guidance of auvs are presented. the first part of this dissertation addresses the problem of dynamically modeling of auvs, and derives thrusters " two - dimension nonlinear dynamic model, which has axial flow speed and propeller rotational velocity as two state variables, voltage or current of motor as inputs, and thruster force and torque as output. the second part focuses on the nonlinear adaptive sliding mode control of auvs in diving plane and steering plane

    本論文系統研究了自主式水下航行器的建模、非線性自適應滑模控制、以及深度調整和水平面導引方法等問題，具體成果和創新點如下1 、根據流體力學理論，建立了螺旋槳推進器的動態模型，它以螺旋槳來流速度v _ p和螺旋槳轉速n為狀態變量，以電機施加轉矩為輸入，螺旋槳推力t和轉矩q為輸出。
  2. Apply computer chip to control the circuit ; omron opto - elecrtonic control - ler and panasonic and mitsubishi inverter have stable performance, high precision, rapid reaction and long life - span ; the controlling plate applies tactile operation board which is handled easily ; vertical structural screen is easy to adjust the vertical printing pressure so as to ensure the quality of printing ; the frame lift is driven by electrical motor and installed with imported linear guide rails, of which the speed - adjust device, scraper and scraping blade can be adjusted within15 to 45 and can be set for many times so as to repeatedly printing with good precision and output, the flat bed is made of 2mm stain - less steel plates which are flat, smooth and indeformable ; it is also equiped with micromatic setting device in order to ensure the precision of multi - color overprint and auto air - intake device to ensure strong adsorption

    採用電腦板控制電路，歐姆龍光電控制器，松下，三菱變頻器，行直穩定.精度高，反應快，壽命長，控制面板採用觸摸式操作面板，操作方便，六式結構型網版垂直升降印刷壓力可調保證印刷質量，機架升降採用電機驅動安裝進口直線導軌，刮刀、回墨刀可在15一45角調整，可設置多次，重復印刷保證產品精度.平臺板採用2毫米不銹鋼板製作，平整光滑不變形配有微調裝置，確保多色套印精度，配自動吸氣裝置，確保強有力的吸附。
  3. At first, according to the concrete requirement of the servo control system, a collective scheme, which provide guarantee to meet the requirements of the global performance, is established. in this scheme, the structure of gimbal and the torque motor driven mode are adopted, and angle measurement is accomplished by inductosyn and velocity measurement is accomplished by dynamically tuned gyro respectively

    首先，根據目標真值測量設備伺服系統的具體要求，確定了地平式常平架結構，力矩電機驅動，分別採用動力調諧式速率陀螺儀及圓盤式感應同步器作為速率及位置反饋元件這一總體方案，為伺服系統滿足整體性能指標要求提供了保證。
  4. Abstract : based on the electronic focus technology development of state - of - the - art, the paper suggested a complete apparatus s cheme ofauto - focus based on sspd ( self - scanned photodiode array ) and 8098 singl e chipprocessor, giving out a focus criterion algorithm based on image high freq uencystatistics. the function of auto - focus of both reflected and transparent o pticalmicroscope was realized. meanwhile some corresponding problems such as sta bility of lightsource, step motor driving etc. were also discussed, which greatly improved the accuracy andreliability of the system

    文摘:在介紹與分析了國內外電子調焦系統的技術發展與現狀的基礎上，提出了一種基於sspd （自掃描光電二極體列陣）與8098單片微處理器自動調焦的整體技術方案，給出了基於圖像高頻成分統計的聚焦判識演算法，在此基礎上實現了反射式與透射式光學顯微鏡的自動調焦，同時對系統的可靠性有關的其它相關問題如光源穩定性、步進電機驅動等問題也進行了討論。
  5. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  6. Machine allows transverse left / right moving, adjusted by electric motor

    本機器可左、右橫移，以電動馬達方式調整
  7. This thesis focuses on the ingress process module of ctu, which translates c - 5 dcp format to rainier 4gs3. the specification analysis, architecture and logic design, functional simulation testbench design, synthesis report and testing result are discussed in this thesis. the research work mainly includes : the specification analysis and design requirements of ctu logic ; the architecture and logical design of ingress process module, which includes receive control fsm, send control fsm and cell position adjustment logic ; the performance improvement of ingress process module to receive and transmit data cell at the full line speed

    本論文的主要研究工作包括：通信協議轉換邏輯的功能分析和設計需求；通信協議轉換邏輯上行方向的系統分析及體系結構設計，包括上行接收狀態機、發送狀態機、信元內位元組位置調整機制等的設計；通信協議轉換邏輯上行方向的線速設計，主要是上行接收的線速設計，要使用流水設計技術；提出了高速實現roundrobin調度策略的實現方法，並設計實現了桶式移位器和優先級編碼電路；應用bfm模擬模型設計了上行處理各模塊的模擬testbench ，完成了各級模塊的模塊模擬和系統集成模擬。
  8. The way that two kinds of different potentiometer feeding back the blade gap value in adjusting mechanism of cnc shear have been introduced

    摘要介紹了數控剪板機刀片間隙自動調整機構中兩種不同電位器反饋刀片間隙值的方式。
  9. Aiming at the problems in the field of the government for hydraulic turbine, this thesis applies the technology of programmable controller to the speed control of hydroelectric generators in hydropower station. a digital regulating system based on the fx2 programmable controller for the water - gate and paddle of hydraulic turbine is developed. first, the turbine regulating system is briefly introduced and the mathematics model of the system is derived

    本文針對當前我國水輪機調速器領域技術現狀，將可編程式控制制器技術應用於水電廠發電機組的轉速控制，提出了在應用可編程式控制制器實現導葉控制系統的基礎上，以可編程式控制制器實現導葉、輪葉雙調整控制系統，並參與研製了以fx2可編程式控制制器為核心的水輪機雙調節控制器，樣機的實際運行良好，系統的軟硬體設計得到驗證，結果令人滿意。
  10. The whole circuit ' s timing generation and synchronization was realized with cpld. as the channel of data transmitting, pof can isolate high voltage part and low voltage part efficiently. at the same time, a single chip processor was used to design a digital meter for the fiber current transducer

    系統採用cpld實現整個工作電路的時序發生和同步協調，利用光纖實現高壓部分和低壓部分的完全電氣隔離和實現信號傳輸，採用單片機技術實現混合式光纖電流互感器專用數字顯示儀表的設計。
  11. There is difference frequency measurement requirement for every part of pid regulating, difference between dynamic quality and static quality in response time and accuracy. according to these, it use the interrupt functions and high - speed counter of the simens s7 - 200 plc cpu226 basic unit and some peripheral circuit to measure frequency ; in software designed, the procedure frame of hydraulic - turbine governor and disperse process of parallel pid are analyzed, an improved pid algorithm is adopted to realize a pid regulation mode with variable structure and parameters ; the mechanical liquid - pressure system of the hydraulic - turbine governor is with electric - hydraulic converter unit of step motor. according to the drive character of five phase of response step motor, a variable frequency regulated voltage driver unit is designed in order to realize interface between plc and driver of step motor

    本文利用s7 - 200plc自身的特點設計了頻率測量單元，根據pid調節各個環節的特點，以及調速器動態特性、靜態特性對頻率測量的實時性和精度要求的不同，利用s7 - 200plc基本單元中內置的高速計數器以及相應的外圍放大整形、分頻電路，實現了水輪發電機組頻率的測量；在軟體上，對微機調速器的整個程序框架、並聯pid的離散化過程進行了分析，選用改進的pid演算法實現了變參數、變結構的pid調節模式；調速器的機械液壓隨動系統具有步進電機電液轉換元件，採用五相反應式步進電機，根據其驅動特性設計了變頻調壓驅動器，實現plc與步進電機驅動器之間數字介面。
  12. Gca silicon commutate battery charger are the ideal portable tools for charging, they are composed with the conditions of voltage dropping through rectifier transformer, then the bridge rectifying of rectification circuit. the output full - wave pulstin current charge the storage battery. the voltage changing composed with multiband switch. the outputcurrent can be adjusted. this kind of product used any moment onctarging anyplace

    Gca系列整流充電機是由整流變壓器的降壓，再經過流電路的橋式整流，輸出全波脈動直流對電瓶進行充電，電壓調速同多頭波段開關組，輸出流可以調節，該產品用任何需要補充充電的場所。
  13. Characteristics of structure : this machine adopts shaft type speed reducer drive which covers less space and can be conveniently repaired. upper supporting roller adopts clamping type fixu which can be conveniently installed. furthermore, it can well regulate deflection of conveying belt ; holdback is set for speed reducer with reliable performance to prevent back - slippign of the glusive belt ; dumper has three types : pneumatically actuated, electric and manual ; course of direction - change roller of the rail has three types : 300, 500 and 800

    2結構特點：該機採用軸裝式減速器驅動，佔用空間尺寸小，安裝維修方便上托輥採用夾緊式固定，安裝方便調整輸送帶跑偏能力強，減速器內設逆止器，防止膠帶倒滑的性能可靠卸料器有氣動電動和手動三種驅動型式尾部改向滾筒張緊行程有300 500 800三種，用戶可接輸送距離的1100選取。
  14. The press has its own indeperdent dynamic mechanism and electric system and use pushbuttons controlling system. three operation modes of adjustment, manual and semi - auto operations can be realized

    本機具有獨立的動力機構和電器系統，採用按鈕集中控制，可實現調整、手動及自動三種操作方式。
  15. Then a dynamic compensating system is designed and added into the measuring system to accomplish the compensation. furthermore, a mcu system is designed to acquire, process and display the output of the transducer ' s serving circuit, and to feed back the workpiece ' s real time dimension to the nc grinding machine

    同時，設計了一個單片機系統來對氣隙式電感傳感器及其調理電路的輸出信號進行採集、處理、顯示，並反饋給磨床，實現對磨床磨削加工的閉環控制，並且使整個系統具有友好的人機交互界面。
  16. According to the present problems and developing tendency of hydraulic turbine governor, four main issues of this field are studied in this paper. the content include hydraulic control system, frequency measurement unit, stability of the discrete control system, optimization of control parameters and self - adjusting pid control strategy based on fuzzy logic. several main achievement and results are obtained and shown as follows : the electric - hydraulic pilot valve driven by step - motor is firstly proposed, which solves the problem that the electric - hydraulic converter of hydraulic turbine governor hydraulic servo is prone to be stuck and blocked and improves the systemic stability greatly

    本文根據水輪機調節領域存在的問題和發展趨勢，對水輪機調速器的液壓控制系統、頻率測量環節、離散調節系統穩定性與調節參數最優整定以及適應式參數自調整pid控制策略進行了研究，得到以下主要成果和結論：首次提出了採用步進電機驅動的步進式電液引導閥，從根本上解決了水輪機調速器電液隨動系統中存在的電液轉換元件發卡、堵塞問題，使電液隨動系統的可靠性大大提高。
  17. Start turn on the electric switch of the gasoline engine, quickly pull the rebound starting handle, start the engine by using the rebound starter, adjust the speed of engine well

    開機打開汽油機電門開關，快速拉動啟動繩手柄，利用反彈式啟動器啟動汽油機，調整好汽油機怠速。
  18. Based on it, a new - style step - type electric - hydraulic servo is developed which simplifies the structure and improves the reliability of the governor, and the mathematical model and its stability control equation are obtained

    在此基礎上，提出一種全新的步進式電液隨動系統，使調速器整機簡單可靠；同時在建立該隨動系統數學模型的基礎上，得出了其穩定性控制方程。
  19. The main design work as follow : four biomedical analog signals input channels " design ; the design of at89c51 microprocessor system which can change the sampling rate ; the dma interfacing circuit design by which the sampling data enter the computer ; the interfacing circuit design between pc and signal amplifier, and the reliability and anti - interference design of this system, etc

    具體設計內容包括：四路生物醫學模擬信號輸入通道設計；以at89c51為核心的可實現采樣速率程式控制調整的微處理器系統設計；采樣數據進入pc機的dma介面電路設計； pc機與生物信號放大器之間聯系的介面電路設計；以及系統的可靠性和抗干擾設計等。
  20. Considering the typical nonlinear characteristics of srm drive system which make the constant parameters of traditional controller unable to adapt to the random disturbance parameters in a large scale, the fuzzy control is introduced to improve its performance. a fuzzy self - tuning controller is designed, which can adjust parameters automatically and improve its static and dynamic performance

    鑒于開關磁阻電動機調速系統顯著非線性造成固定參數在常規控制方式下不能很好適應工況大范圍變化的問題，引入了模糊控制來改善其性能，設計了模糊自校正控制器，實現了參數的在線優化調整，提高了系統的靜、動態性能。
分享友人
分享到 Line

分享到臉書