檢驗軸 的英文怎麼說
中文拼音 [jiǎnyànzhóu]
檢驗軸
英文
proof bar- 檢 : Ⅰ動詞1 (查) check up; inspect; examine 2 (約束; 檢點) restrain oneself; be careful in one s c...
- 驗 : 動詞1. (察看; 查考) examine; check; test 2. (產生預期的效果) prove effective; produce the expected result
- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 檢驗 : checkout; test; examine; inspect; verify; survey; check;checking;testing;[英國]jerque(指檢查船舶...
-
Testing and cortrolling methods of grinding badness layer of bearings working surface
軸承工作表面的磨削變質層的檢驗及控制方法。Gudgeon pins for reciprocating piston engines ; dimensions, types finish, requirements, tests
活塞式發動機用軸頭銷.尺寸加工型式要求檢驗In order to measure the field of view matching of digital binoculars, the depth of optic axis parallelism and field of view matching are measured respectively. the collimator and pre - set lens are used to measure the depth of parallelism of optic axis. field of view meter is used to measure the field of view of binoculars and camera
為了檢驗數碼望遠鏡的視場匹配度,提出了採用平行光管和雙管前置鏡的組合測量光軸平行度以及採用視場儀測量數碼望遠鏡的望遠鏡和數碼相機的視場大小的方式,並對數碼望遠鏡的視場匹配度與望遠鏡和數碼相機的視場大小關系進行了理論推導,導出了數碼望遠鏡的視場匹配度測量的實際計算公式。Nowadays, the machining center carries through the precision inspection only following the fixed coordinates " axes, which can not completely reflects the real error of the spacial position of the practical machining outside the axes and leads to having no the directive relation between the inspected precision and the practical machining precision. so, this paper introduces that the error factors of influencing workpiece ' s outline on machining and carries out the solid inspection of every spot ' s error inside the workaround on the horizontal machining center
本文針對當前加工中心僅沿固定的坐標軸線進行精度(含幾何精度和定位精度)檢驗,並不完全反映軸線外實際加工的空間位置真實誤差,導致檢出精度與機床實際加工精度無直接對應關系的現狀,論述了加工時影響工件型面輪廓精度之加工中心的誤差因素,對加工中心實施其工作區內各點誤差的立體檢測。Plain bearings - thin - walled half bearings - checking of peripheral length
滑動軸承.薄壁半軸承.周長檢驗Plain bearings. methods of dimensional control. peripheral length checking of thin - walled half bearings
滑動軸承薄壁軸瓦周長的檢驗方法Plain bearings - thin - walled flanged half bearings - dimensions, tolerances and methods of checking
滑動軸承薄壁翻邊軸瓦尺寸公差及檢驗方法Plain bearings : metric series - dimensions, tolerances and methods of checking thin - walled half bearings
滑動軸承規范.米制系列.第5部分:薄壁半軸承的尺寸公差及檢驗方法Z test conditions for machining centres - geometric tests for machines with integral indexable or continuous universal heads vertical z - axis
加工中心檢驗條件.第3部分:分度或連續的萬能主軸頭機床的幾何精度檢驗Rules for the inspection of axial - flow alternating fans for export
出口軸流式交流排氣扇檢驗規程The study of premature fracture failure of these shafts was made by means of sem inspection, microstructure examination and chemical composition analysis
採用金相檢驗、掃描電鏡和化學成分分析等手段,對斷裂變速箱二軸進行了檢驗分析。Engine crank depletion analysis and testing
汽車發動機曲軸耗損分析及檢驗Spline hobbing machines ? testing of the accuracy
花鍵軸銑床精度檢驗Fibre optic interconnecting devices and passive components - basic test and measurement procedures - examinations and measurements - measurement of the angular misalignment between fibre and ferrule axes
光纖互連器件和無源元件.基本試驗和測量程序.檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 26 : examinations and measurements ; measurement of the angular misalignment between fibre and ferrule axes
光纖互連設備和無源元件.基本試驗和測量程序.第3 - 26部分:檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量Meanwhile, mabs - 3000 not only is the combination of the three different systems : roller braking test, vehicle axle weight and speed meter test, but also has more functions, less pollution, lower cost and a more efficient composite system
該多功能abs檢驗臺在檢測汽車防抱死制動系統( abs )性能的同時還把汽車的速度表校驗、軸重檢測、制動性能檢測三個分離的試驗臺的功能合為一體,是一種集成度高、多功能的復合試驗臺。Main bearing of main engine no. 1. unit dismantled for survey
主機第一缸主軸承拆開檢驗。Cylindrical gears - code of inspection practice - recommendations relative to gear blanks, shaft centre distance and parallelism of axes
圓柱齒輪.檢驗實施標準.與齒輪坯料,軸心距和軸的平行度相關的推薦值Verification of static uniaxial testing machines - part 2 : tension creep testing machines - verification of the applied force
靜力單軸試驗機的檢驗第2部分:拉力蠕變試驗機施加力的檢驗Standard specification for magnetic particle examination of continuous grain flow crankshaft forgings
連續晶粒流動曲軸鍛件的磁粒子檢驗標準規范分享友人