次相容的 的英文怎麼說
中文拼音 [cìxiāngróngde]
次相容的
英文
sub consistent-
The way of taking one nth out of capacitor ' s the first harmonic capacitive reactance as its nth harmonic impedance is verified whit the data from tang7c. according to the approximately estimating method, the first harmonic impedance of 220kv system is calculated. on the basis of the models, this paper gives the harmonic equivalent circuit of substation and gives the b ( n ) function of the harmonic time n. when the capacitors has different combination, b ( n ) ' s value will also change, with the inputting local measurement data, the paper studies the series and parallel resonance at the substation, and deduces that the reason the capacitor ' s fuse of tang6c is frequently interrupted is that its capacitor current contains a large number of 5th harmonics, and that the reason the discharging pt of tang7c capacitor being exploded is also that the 7th and 9th harmonic currents are amplified
據此，對該站進行了串聯諧振分析和並聯諧振分析，並結合測試數據和有關變電站的運行記錄，指出了導致該站電容器湯6c頻繁燒保險的主要原因是5次諧波電流含量偏高，引起湯7c放電pt爆炸也是因為7次和9次諧波電流被放大。針對這些導致湯陰變電站補償電容器故障的原因，提出了相應的諧波治理措施，包括針對湯6c電容器5次諧波電流含量偏高的原因，提出了停運湯6c電容器或者通過把湯sc電容器的部分容量併入湯6c電容器（湯sc其餘部分停運）以增加湯6c諧波承受能力的措施;針對# 2變低壓側7次和9次諧波電流被放大的現象，提出了在湯7c電容器上加裝一定百分比的串聯電抗器的措施。From 1929 to 1943, with the currency system changing to the floating exchange rate system, each monetary bloc implemented the strict foreign exchange management, and competed to use the depreciation policy to stimulate the exportation, resulting in " he changes rate war "
這次人民幣匯率形成機制改革的內容是，人民幣匯率不再釘住單一美元，而是按照我國對外經濟發展的實際情況，選擇若干種主要貨幣，賦予相應的權重，組成一個貨幣籃子。The chemical compositions of sei films formed on the interfaces of a3000 samples in different electrolytes during the first charging process are mainly li2co3 and lioco2r, but their textures are different. the sei films formed in ec - based electrolytes are thin and compact, which can prevent the solvated lithium ions from cointercalating between two graphene layers of the graphite crystallites effectively, therefore samples a3000 have small irreversible capacities and good compatibilities with this kinds of electrolytes. however, the sei films formed in pc - based electrolytes are thick but defective, which could not effectively prevent solvated lithium ions from intercalation, therefore sample a3000 shows large irreversible capacities in pc - based electrolytes and bad compatibilities with this kind of electrolytes
A _ （ 3000 ）試樣在六種不同的電解液中，首次充電過程中所形成的sei膜，其化學組分均為碳酸鋰和烷基碳酸鋰，但在ec基電解液中形成的sei膜薄而緻密，可以有效地阻止溶劑化鋰離子插入石墨層間，不可逆容量少，表現出與a _ （ 3000 ）試樣有良好的相容性；在pc基電解液中形成的sei膜厚，且有缺陷，不能有效地阻止溶劑化鋰離子嵌入試樣中石墨微晶的層間，不可逆容量大，與a _ （ 3000 ）試樣的相容性極差。It may be readily seen that the temporal structure of everyday life is exceedingly complex, because the different levels of empirically present temporality must be ongoingly correlated
我們很容易看出日常生活的時間結構是極端復雜的，因為經驗當下時，時序性的不同層次一定是持續相關的。Because the well reservation of the advantages of traditional large sacle advertising airboat, thoughtful design and argumentation on every level has been made, the dimension of the airboat reduced to 9 - 16 meters, adaptable area remarkably increased, flying agility obviously improved, a place as large as a playground is enough for it s taking off or landing, a space as size as a bus warehouse is sufficient to store the airboat, the advertising area of the airboat on it s two sides become less to 9 - 12 square meters, the altitude where such airboat can fly is much lower than that that drives person, presenting a little difference in views of the people on the ground, so capable to take the place of human - driving airboat, on the other hand when the size reduced, the operation, use, freight and maintenance become very easy, easy operation become it s first advantage : remote controllable, no professional driver needed, common personal can operate it after a short trainning, trainning time ranges from 3 - 5 days single, 15 - 30 days for people
是因為它完美的保留和發展了大型載人廣告飛艇的優勢，為此我們進行了方方面面且深入細致的設計和論證，首先縮小了飛艇的尺寸， 9至16米長，大大的增加了飛艇的適用范圍，使飛行的靈活性得到了改善，學校操場大小的地方就可從容的起飛降落，大客車或大貨車的車庫便能存放，廣告面積雖然也小了，每單側9至12平米，可遙控飛艇的飛行高度也比載人艇的飛行高度低很多，以地面的視覺效果來看效果相差非常小，足以代替載人艇，其次是飛艇縮小后，整艇的操作使用運輸維護也都大大的簡化了，操作簡便是它的第一大優點：由於是遙控飛艇，就不需要專業的駕駛員來操作，普通人經過短期的技術培訓就可勝任，培訓期每單人為三至五天，多人視人數十五至三十天。He was still her antinous, her apollo even ; his sickly face was beautiful as the morning to her affectionate regard on this day no less than when she first beheld him ; for was it not the face of the one man on earth who had loved her purely, and who had believed in her as pure
他仍然是他的安提諾俄斯，甚至是她的阿波羅他那張滿是病容的臉，今天在她愛情的眼光看來，還是和她第一次見到他的時候一樣，像黎明一樣美麗，因為在這個世界上，只有這個人的臉曾經純潔地愛過她，也只有這個人相信她是一個純潔的人。As an important component of the above researches, this paper covers following aspects : ? firstly, product design theories are summarized, status and development trend of machinery product design are analyzed, and application of knowledge based design method in machinery product design is put forward. ? kbe ( knowledge based engineering ) theories such as knowledge acquisition, representation and storage are discussed, kbe concept is integrated with ug secondary development technology, and design knowledge is induced and stored to establish the design knowledge base. ? product case representation is researched, a hierarchical tree type product case library for complex products is established, retrieve strategy for cases of the nearest filed is put forward and corresponding algorithm is given
本文的主要研究內容及成果如下: ?對產品設計理論和方法進行了總結和概括，分析了機械產品設計的現狀和發展趨勢，將基於知識的設計方法應用到機械產品的設計中; ?研究了知識獲取、表達、存儲等kbe理論，並將kbe思想應用到ug二次開發中，將設計知識歸納存儲，建立了設計知識庫; ?研究了產品實例表示，建立了復雜產品層次樹狀產品實例庫，介紹了最近鄰域實例檢索策略並給出相應的演算法; ?研究了基於知識重用的三維產品建模技術，研究了在設計過程中的設計資源的重用，計算過程的重用，計算數據的重用，推理過程的重用等等;介紹了基於設計重用的凸輪三維模型的實現方法。Abstract : the paper tries to illustrate the compatibility and incompatibility between concepts and their orders by probing into the realtions of the concepts, which gives reader a clear understanding of the concepts, the order and the compatibility of the concepts and to direct their work
文摘:力求通過概念之間關系的探討，理清概念間相容與不相容以及它們的層次關系，使人們對概念及概念的層次、相容等關系有一個清楚的了解，以指導工作實踐With the development of the network and the multi - processor system, the research, simulation and the impemeni of the system - level fault diagnosis which is the very important means to increase the reliability of the system, are becoming more and more important. on the system - leve1 fault diagnosis, based on the group theory of system - level fault diagnosis that has been put forward by pro f zhang, the paper constructs newly the theory bases, improves on the matrix method, reinforces and consummates group arithmetic of all kinds of test mode, for the first time, analyses and discusses the equation solution of all kinds of models, so al1 the consistent fault patterns ( cfp ) could be found, straightly and high efficiently, even if the sufficient and necessary condition of t - diagnosable is dissatisfied and the complexity of system - level fault diagnosis is greatly decreased, especialy in strong t - diagnosabl6 system. last the simulation system ' s function has been extended and the application hotspot and the development trend have been disscussed
本人在張大方教授等人提出的基於集團的系統級故障診斷的理論基礎上，重新構建了系統級故障診斷的理論基礎，定義了系統級故障診斷測試模型的三值表示；改進了系統級故障診斷的矩陣方法，重新定義了測試矩陣、鄰接矩陣、結點對、結點對的相連運算、極大準集團和斜加矩陣，由此能直觀、簡便地生成集團和極大獨立點集；補充和完善了各類測試模型的系統級故障診斷的集團演算法，通過定義集團測試邊和絕對故障集，簡化了集團診斷圖，由此能較易地找到所有的相容故障模式，即使不滿足t -可診斷性，大大減少了系統級故障診斷的復雜度，尤其是對強t -可診斷系統；首次分析探討了各類測試模型的方程解決，由此從另一角度能系統地、高效率地求出所有的相容故障模式（ cfp ） ：擴充了系統級故障診斷模擬系統的功能，快速、直觀和隨機地模擬實驗運行環境，進行清晰和正確的診斷，同時提供大量的實驗數據用於理論研究，優化演算法和設計。The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。Galliani added : " we will now start negotiations with chelsea, but they won ' t be easy
加利亞尼補充道， 「我們將開始和切爾西展開談判，但這不會是一次很容易的談判，我相信。 」The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance
通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。The correlative items of dc filters are researched on the basis of gezhouba - shanghai hvdc transmission project. in the analysis the three - pulse model is used to simulate converter, which takes into account the impact of the stray capacitance. the harmonics distribution on dc lines is simulated accurately, especially the harmonic ignored in old models
本文以葛上直流輸電工程為基礎，研究直流濾波器設計中的相關問題，採用考慮了雜散電容的三脈動模型來建立換流站模型，更為準確地模擬出直流輸電線路上的諧波分佈情況，尤其是模擬出舊模型中忽略的次（為自然數）諧波，為直流濾波器的設計提供了更精確的數據和判斷依據。Several materials with large coefficient of expansion were selected to make packaging components, and it was found that the packaging materials have good temperature sensitivity and compatibility with optical fibers. experimental accuracy and repetition of fbg temperature sensitivity and compensation were discussed. have selected several materials which has bigger coefficient of expansion to do packaging components, have made many temperature experiments, there have not flaws, such as aging, crackle, absciss layer, packaging materials have good temperature sensitivity and compatibility with optical fiber ; have designed the simple and practical packaging components, have performed a serials of experiments about accuracy and repetition of fbg wave - length, have obtained the first step conclusion ; have analyzed the result and made comparison between the result of different experiment, have summarized the best packaging effect and several rules to reduce mistskes
本文所做的主要工作包括以下幾個內容：一、選取了常見的熱膨脹系數大的材料製作封裝元件，經過多次一80到80反復測試，封裝元件沒有出現老化開裂、封裝裂紋、空洞、離層等缺陷，封裝材料具有良好的溫敏穩定性及復用性，與光纖相容性較好；二、對光纖光柵進行簡單、實用的封裝處理，就封裝效果的優劣性、波長測量的準確度、重復性和封裝時產生的波長損失等方面進行了一系列的實驗，得出了初步的結論；三、對溫敏和溫度補償式封裝的實驗數據進行了詳細的分析和對比，從數字上對溫變過程中光纖光柵中心波長的改變及溫變曲線進行了定量的分析，在大量實驗數據分析結果的基礎上，總結出哪種材料封裝效果更好，以及如何有效的減小實驗誤差。Attention to consistency between tables of contents and texts in sci - tech periodicals
重視科技期刊目次表與正文相應內容的一致性The former is original version, the later is the revised version issued in the eleventh year of guangxu
這兩種版本內容基本相同，差異主要表現在目次編排上，表現了編纂者不盡相同的編纂理念。The results show that under the same lapping conditions the si3 n4 ball has the lowest material removal rate and the best roundness and roughness, followed by zro2, al2o3, and sic ball
結果表明：在相同的研磨條件下，具有長柱狀晶粒的氮化硅陶瓷球加工速率最低，但圓度和表面粗糙度最容易控制；氧化鋯和氧化鋁陶瓷球表面質量次之，碳化硅陶瓷球加工速率最高，圓度和表面粗糙度最難控制。On the view of situation, the thesis settles the position, characteristic and the development of the primary state of the socialism in china, which is to analyze the history position and characteristic of the primaiy state of the socialism in china and to point out the general plan of the construction on the basic of sum up the thought way of the theory of social economy state of marxism. the mainly used methods of analysis are : ( 1 ) the research of the process, construction and the layer level are associated. the thesis not only analysis the historical formation, but also analysis the constitution and the layer level, so as to consolidate the various theories of the marxism, and to understand the theoiy of social economy state of marxism systematically
本文的主要分析方法是:把社會經濟形態的過程論、結構論、層次論相結合，不僅分析社會經濟形態的縱向發展歷程，並且分析其橫向構成形式，還分析其歷程和構成的內部層次，從而使馬克思相關的豐富而多樣的論述統一到一個整體中來，以便全面、系統地理解和把握馬克思的社會經濟形態思想;把理解馬克思的論著資料與體會其思想邏輯相統一，既廣泛引用馬克思論著的眾多原文原句，又充分領會馬克思的整體思想內涵，在研究其論著資料中體會其思想內容，在分析其思想邏輯中運用其論著資料，以達到客觀、完整地理解和把握馬克思的社會經濟形態思想;注重理論研究與現實實踐相一致，既尊重馬克思的真實思想，又聯系社會實踐，特別是當今時代的現實和中國社會主義初級階段的建設。This thesis for the first time bases its analysis on the maintenance characteristics and repair mechanisms for crack filling and pothole repair in asphalt roads. it analyzes the properties of the aggregate and the bituminous binder in patching materials, and further analyzes the compatibilities of the aggregate and the bituminous binder, patching materials and old pavement materials. furthermore, it determines the grading types, the mineral aggregate gradations, the application rate of asphalt, the principle of selecting component materials and the air void
本文首次依據瀝青路面裂縫填封和坑槽修補的維修特性和修補機理，全面分析了修補材料中集料與瀝青結合料應具備的性能要求，並對集料與瀝青結合料、修補材料與原有路面材料的相容性進行了深入的分析，同時分析確定了修補材料的級配類型、礦料級配、瀝青用量范圍、組成材料的選用原則及空隙率等。From the view of service marketing, this paper discussed shipping marketing mix, some new point of view is brought forward
其次，航運企業提供的是一種服務產品，相應的其航運市場營銷屬于服務營銷的內容。分享友人