正常充電電流 的英文怎麼說

中文拼音 [zhēngchángchōngdiàndiànliú]
正常充電電流 英文
normal charging current
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 充 : Ⅰ形容詞（滿; 充足） sufficient; full; ample Ⅱ動詞1 （裝滿; 塞住） fill; charge; stuff 2 （擔任; ...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 正常 : normal; regular; average
  • 電流 : current; galvanic current; electric current; electricity; current flow電流保護裝置 current protec...
  1. It shows that the injection quantity and the difference of temperature distribute as a parabola which is at the same load, and the minimum of the parabola corresponds to the optimum quantity of injection ( g ). under the condition that the quantity of injected mass, the air speed and the heat quantity is respectively g, v and q, the research demonstrates that the pentium iv chip ' s temperature variation can be controlled under 40c and work normally when the wind speed overpass 1. 5m / s and the power dissipation of the chip is 60w. otherwise this paper calculates the flooding limit of thermosiphon with several different methods

    對其充灌量、散熱量、電子元件（ cpu模擬晶元）表面與環境溫度之差及通風、流速的影響進行了系統的測試，發現充液量與溫差的關系在負荷不變時呈拋物線分佈，其極小值點對應的充液量是最佳充液量g 。在充液量為g時，對風速v 、散熱量q進行的研究表明，當風速超過1 . 5m / s后，奔騰晶元在60w發熱條件下晶元溫度小於40 ，能滿足長期正常工作。
  2. The charge and discharge performances of different composites were studied by the charge and discharge ; the structures of composites were characterized by sem ; the electrochemical properties of sulfur positive materials were characterized by cyclic voltammetry and eis. we studied the charge process, discharge process, charge - discharge efficiency, self heat, and self - discharge of lithium - sulfur system on system shuttle constant, conduct the mechanism of these processes and simply analyse them

    以充放電技術研究了不同類別復合正極的充放電性能;以掃描電鏡技術觀測了復合正極的表面形貌;以循環伏安技術和交流阻抗技術研究了復合正極電極的電化學性能;並初步探討了鋰-硫電池體系中充電過程、放電過程、充放電效率、自熱和自放電等對體系飛梭常數的影響，推導了這些過程的機理並簡要的進行了分析。
  3. The technology of micro - electronics and calculation method was fully made in the system. how to improve the accuracy of standard orifice measurement is also discussed from the following aspects : the means of measurement and transmitter, online correction of measurement parameter and abnormal condition. all those means are used to overcome its shortcomings of less scale of measurement range, short period of checkout, more tache of maintenance and low accuracy of measure

    該系統充分利用微電子技術和計算技術以及通過實際現場總結的經驗，主要從測量與變送環節採取的措施、相關參數的在線實時補償演算法、非正常情況的在線補償三個方面對如何提高量精度加以論述，盡可能地彌補孔板差壓式流量計量程比較小、檢定周期短、維護環節多、準確度低的不足。
  4. Our factory is according to the needs of customer, still the production is charged and against becomes an organic whole machine, and can being charged and can be against becoming, and netting the electricity at ordinary times often can be charged to the accumulator, the net electricity has stopped afterwards use the accumulator with against becoming, makes the 12 volts direct currents change into the 220 volts alternating currents, for person production and the life brought the convenience

    我廠根據客戶的需要，還生產充電、逆變一體機，既可以充電、也可以逆變，平時網電正常時可以對電瓶充電，網電停了之後可以利用電瓶和逆變，使12伏直流電轉換成220伏交流電，為人門的生產和生活帶來了方便。
分享友人
分享到 Line

分享到臉書