正弦機 的英文怎麼說

中文拼音 [zhēngxiánjī]
正弦機 英文
sinusoidal machine
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 機 : machineengine
  1. This has since been confirmed by russian sources ; the transmitter consists of two swept - frequency generators of sinusoidal voltage and two parallel horizontal grounded antennas, each about 60 km long

    這一點被來自俄方的消息所證實；發射機有兩個掃頻發生器，產生正弦波，同時有兩幅相互平行的水平地面天線，每個天線有60千米長。
  2. Experimental results certify that the proposed flyback inverter features small thd in the output sinusoid voltage, small size, light weight and fast dynamic response

    研製的100va原理樣機實驗結果表明，該逆變電路輸出正弦電壓失真度小，體積小，輸出動態及靜態性能良好。
  3. The paper researches rectangle, parabola, sinusoid and triangle acceleration curves and their response characteristics, and puts forward a concept of combined acceleration

    摘要研究了輸送機的各種加速度（矩形、拋物線形、正弦形和三角形）曲線及其響應特性，在此基礎上，提出了組合加速度的概念，並對其進行了研究。
  4. Permanent magnet synchronous motor ( pmsm ) drived by triphase sinusoidal current is research object in this paper. its mathematics models in several coordinate are set up, controlling principles of flux linkage and torque are discussed under dtc and the block diagram of pmsm with dtc is presented

    本文以三相正弦波驅動的永磁同步電機（ pmsm ）為研究對象，建立了其在不同坐標系下的數學模型，並深入探討直接轉矩控制中永磁同步電機的磁鏈和轉矩的控制思想，給出控制方案。
  5. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  6. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反電動勢類似正弦的準正弦波反電動勢無刷直流電動機，本文提出一種基於六個離散位置信號的自同步svpwm （電壓空間矢量法）控制方法，用以削弱電磁轉矩脈動，分析了實現這種方法的主要控制環節，包括起動時電壓空間矢量的初始定位，阻抗角與電流超前角的合理選擇以及連續轉子位置的估計等。
  7. Furthermore, this dissertation also gives a comprehensive analysis and comparison to the torque ripple factor, torque - current ratio and other aspects for pseudo - sinusoidal emf bldcm drived by 120 conduction mode, 180 conduction mode and self - synchronous svpwm mode respectively. the simulation and the experimental results indicate that self - synchronous svpwm method is more effective for minimizing the torque ripple without any expense of the torque - current ratio when the crest width of the back - emf waveform is less than 107 electrical angles

    對準正弦波反電動勢無刷直流電動機在120導通方式、 180導通方式和自同步svpwm三種控制方式下的轉矩脈動系數、轉矩電流比等方面進行了全面的分析與比較，模擬研究和實驗結果表明，當反電動勢的平頂寬度小於107電角時，採用自同步svpwm控制方法可以在不損失轉矩電流比的基礎上，更有效地抑制電磁轉矩脈動。
  8. For the bldcm which has a general crest width of the back - emf waveform, two kinds of torque ripple conditions when drived by sine - wave current as well as by square - wave current are deduced based on the mathematical models. in addition, a comparison is carried out between these two conditions, which indicates that sinusoidal current driving is more favorable to minimizing the torque ripple when the crest width of the back - emf waveform is less than a certain value

    闡述了抑制齒槽轉矩措施對反電動勢波形的影響，利用無刷直流電機的數學模型推導並比較了任意平頂寬度梯形波反電動勢在正弦波和矩形波兩種電流驅動下的電磁轉矩脈動情況，得出在梯形波平頂寬度減小到一定數值后採用正弦電流驅動更有利於減小電磁轉矩脈動。
  9. This dissertation mainly investigates some robust control strategies of the electromechanical actuator which is supposed to be activated by the sinusoidal permanent magnet synchronous motor ( pmsm ) and limited angle torque motor ( latm )

    本文主要研究了基於正弦波永磁同步電機（ pmsm ）及有限轉角力矩電機（ latm ）驅動的電動舵機的魯棒控制策略。
  10. Voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed

    採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源
  11. Abstract : voltage segment network constituted by electron switch of bta and controlled by single chip microcomputer constitutes a new fast electronic regulator. for bta cross zero touch off, sine wave which is exported is integrity. a new way to generate stable ac current is found with feed back control system by single chip microcomputer. so a new high power ac current regulator is developed

    文摘:採用單片機控制雙向可控硅作為電子開關所組成的電壓分節網路，組成新穎快速的電子調壓器；由於雙向可控硅過零觸發，所以其輸出是不失真的完整正弦波；再用單片機組成反饋控制系統，從而找到了交流穩流的新方法，研製出一個大功率交流穩流電源
  12. Based on the 3d geometry vision, using java3d, for each of worktable and sine welding seam part of sheet, the ve modeling experiments achieve the construct of macrostructure, security virtual thickness and virtual guide based on error, and accomplish the space restriction of robot running. via the structured laser sensor ’ s getting three - dimension information, the experiments achieve the modeling of sine welding seam part of sheet by using programming

    在立體視覺傳感系統獲得三維信息的基礎上，利用java3d建模技術，分別對工作臺、薄板正弦曲線焊縫工件進行建模實驗，完成了虛擬環境中宏觀環境模型的建立，並根據誤差建立了安全虛擬厚度和虛擬向導，完成了對機器人運動的空間約束;通過結構光傳感器獲得三維信息，編程實現對薄板正弦曲線焊縫模型的建立。
  13. This paper presents the displacement solution to mine elevator viscoelastic vibrating equations and the kinetic tension calculation method, discusses kinetic tension characteristics under rectangular, ladder shaped, sinusoidal and parabolic acceleration curves, provides ways to limit or even avoid lifting rope viscoelastic vibration

    摘要給出了礦井提升機粘彈性振動方程的位移解及動張力的計算方法，研究了採用矩形、梯形、正弦形、拋物線形加速度時銅線繩的動張力特性，給出了限制和消除提升鋼絲繩粘彈性振動的方法。
  14. Adopting the form closure error and the motion transmission error of sine curve to carrying out theoretical analysis of this cam mechanism

    對該凸輪機構採用正弦曲線的形封閉誤差和運動傳遞誤差進行了理論分析。
  15. A nonlinear ship steering controller is designed successfully. even considered the noises caused by wind, wave and current, the matlab simulation tracking error is almost zero. simulation results show that the presented algorithm is effective and robust

    在存在舵機非線性和海浪干擾的情況下，分別跟蹤階躍響應及正弦曲線，航向跟蹤效果很好，幾乎無偏差跟蹤，且打舵小，具有較強的魯棒性。
  16. On basis of the producing fact of kiu ming heavy machine ltd, the author get much fact material through inner research, and presents a imagine of new corrugated - web structure of overhead traveling crane. through enough compare and argumentation, this paper presents using sine curve as corrugated sheet of web

    作者根據昆明重機股份有限公司的生產實際，深入調查研究，在掌握大量生產應用實際的資料基礎上，提出了橋式起重機的箱形主梁的新型波形腹板結構的設想，並在充分比較和論證的基礎上提出了以正弦曲線波形作為腹板的波形。
  17. In the visual 3 - dimensional phase space, the reconstructed attractor of the reverberation exhibits round structure, which contradicts to the irregular distribution of noise and is comparable to the regular circle of periodic wave

    在可視的三維相空間中，混響重構吸引子的相圖呈環形結構，其結構特點介於純隨機過程的均勻無規則散布與確定性正弦周期信號的規則圓形之間。
  18. Specification for digit sine - simulator

    數字正弦機規范
  19. For the first time, three types of sine structures for wavelength linear scale in grating spectrum instruments are described systematically. the tuning structures for wavelength linear scale in both littrow and littman set - up external - cavity laser diodes are designed

    （ 3 ）首次系統地分析了光柵光譜儀器中的三類正弦機構，分別設計了可實現波長線性標度的littrow和littman外腔半導體激光器調諧機構。
  20. The performance of the proposed guidance law is evaluated in three typical maneuver case : a constant target maneuver, a sinusoidal target maneuver, and a random telegraph maneuver

    這是一種對存在隨機目標機動的非線性制導系統進行完全統計分析的計算方法。考慮了三種典型的目標機動，即，階越機動，正弦機動和隨機電報機動。
分享友人
分享到 Line

分享到臉書