正火處理 的英文怎麼說

中文拼音 [zhēnghuǒchǔlǐ]
正火處理 英文
normalizing treatment
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 火 : fire
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  1. Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously

    應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。
  2. This paper analyse the feasibility and necessity of examine and repair about the qiangui co. ltd of generate electricity base on the frmework of guizhou wire network and the run state and exerience of the factory. at the same time, in the base of the lucubrate and analyse of stats examine in domestic and abroad, this paper has analyse the abrupt librate of steamer generator by online data check in pancountry power plant. it acquire obvious effect and prove the applicability and feasibility about the examine in power plant by take correspond measures to ensure the normal operate of the set

    本文根據貴州電網的結構形式以及黔桂發電有限責任公司機組的運行狀況和經驗，進行了黔桂發電有限責任公司實行狀態檢修的可行性和必要性分析，同時在深入研究分析國內外狀態檢修技術基礎上，對盤縣發電廠汽輪發電機組突發振動事例用在線檢測數據進行分析、採取相應措施處理，使機組正常運行，取得了明顯的成效，同時也證明點檢與狀態檢修在火電廠的適用性和可行性。
  3. The asteroids are the most important small bodies in the solarsystem, and they mainly lies in the two locations - a main belt between the mars ' s orbit and the jupiter ' s and the near - earth space. the most feature of the orbits of near - earth asteroids ( neas ) is that the semi - major axes of the orbits are nearly equal to that of the earth or the perihelia distances are approximate to or even less than the mean distance between the sun and the earth, thus they could move into inside of the earth ' s orbit, so that they might close approach or even colliside with the earth ( or other planets, such as the venus, the mars, etc. ). the characteristic brings about some difficulties in the numerical research during their orbital evolution, which leads to the failure of the normalization technique in the general removal impact singularities of celestial mechanics methods and the symplectic algorithm which is successfully applied to the investigation in quality. by comparing the computation effects of several common numerical methods ( including symplectic algorithm ), and considering the nature of the movement of the small bodies, the corresponding treatments are provided here to improve the reliability of the computation

    小行星是太陽系最重要的一類小天體，主要分佈在兩個區域；火星和木星軌道之間的一條主帶和近地空間.近地小行星軌道的最大特點是其軌道半長徑與地球軌道半長徑相近，或近日距離接近甚至小於日地平均距離，其運動可深入到地球軌道的內部，這將導致該類小行星與地球（還有金星、火星等）十分靠近甚至發生碰撞.這一特徵給其軌道演化數值研究帶來一些困難，包括天體力學方法中一般消除碰撞奇點的正規化處理以及對定性研究十分成功的辛演算法都將在不同程度上失效.通過對幾種常用數值方法（包括辛演算法）計算效果的比較，根據小天體運動自身的特性，給出了相應處理措施，從而可提高計算結果的可靠性
  4. On the basis of our previous forging equipment, our company has purchased another fast forging hydraulic equipment of 250 tons, with which we can forge various roughcast of special sections below 20 tons, as well as heat

    我公司在原有的鍛打設備外，又購進一臺250噸的快速鍛打液壓設備，可?根據客戶要求鍛造20噸以下的各種異型鋼材毛坯，還可?客戶提供退火正火回火淬火等熱處理服務。
  5. Ht sub - factory : complete process of annealing, quenching, tempering, quenching and tempering, solution treatment etc

    熱處理廠：可完成退火，正火，回火，調質，固溶處理等工藝
  6. Our company endeavors to quenching & tempering, normalizing, tempering, high and medium temperature quenching, mesh belt furnace quenching, carbonizing, aging subzero and high temperature heat treatment, etc

    本公司是一家致力於從事調質、正火、回火、高中溫淬火、網帶爐淬火、滲碳、時效冰冷及其高溫熱處理的廠家。
  7. Finally, the calculating programs of the processing method of the tested data by doppler radar of the rocket - assisted cartridge have been programmed and the model of the data processing method and the reliability of calculation have been tested and proved by calculation of actual examples

    通過編制火箭增程彈多普勒雷達測試數據處理程序，進行實例計算證明，本文推導的數據處理方法正確可靠。該方法可以用於火箭增程彈多普勒雷達測速數據處理。
  8. Today, salt - bath stove is still one of the main heating equipments in the heat - treating workshops

    鹽浴爐是熱處理車間的主要加熱設備之一，多用於零件的淬火、回火、正火等處理。
  9. We also have advanced heat treatment devices : 6 net strip quality control production lines, 4 quenching production lines, and 22 equipments including trunk oven, well oven, vacuum ion nitrogen oven, vacuum quenching oven, high frequency quenching oven and etc. the completeness of equipment and technical expertise can meet the different requirements of our customers

    公司還有先進的熱處理設備：網帶調質生產線6條，正火生產線4條及箱式爐井式爐真空離子滲氮爐真空淬火爐高頻淬火爐設備等22臺。全的設備和專業的技術能夠滿足不同客戶的各種要求。
  10. The principle of multi - method and multi - parameter is suggested, which should be followed during characterizing microstructures of alloy steels by ultrasonic not method. ultrasonic velocity ( c, ) of transformation products through different heat processes of three steels was measured by high - accuracy ultrasonic installation. the velocity of quenched microstructure of 38crmoal is the lowest, which gradually increases with increasing tempering temperature between 200 ? and 650 ? after quenching process

    利用ti - 40n高精度超聲波測厚儀，研究了超聲波在不同鋼種、不同熱處理轉變產物中的超聲波速度c _ 1 : 38crmoal鋼淬火組織c _ 1最小，淬火后在200 650范圍內進行回火處理時，隨回火溫度的升高， c _ 1逐漸升高， hrc與c _ 1之間具有較好的相關性；正火組織的c _ 1介於淬火后中溫回火及高溫回火產物組織的c _ 1之間。
  11. Flat products made of steels for pressure purposes - part 3 : weldable fine grain steels, normalized

    壓力容器用扁平鋼軋材.第3部分:正火處理的可焊細晶粒鋼
  12. Specification for flat products made of steels for pressure purposes - weldable fine grain steels, normalized

    壓力容器用的扁平鋼軋材規范.經正火處理的可焊細粒鋼
  13. Based on ladle refining, wide flat anvil forge with great forging ratio, heat treatment process of " normalizing + spheroidizing + diffusion hydrogen ", the cold roll blank has been forged succesfully, and the percent of pass is up to 90. 5 %

    採用鋼包精煉爐冶煉、寬平砧大壓下量鍛造、 「正火+球化+擴氫」的熱處理工藝，成功製造了冷輥坯，合格率達90 . 5 。
  14. Abstract : based on ladle refining, wide flat anvil forge with great forging ratio, heat treatment process of & quot; normalizing + spheroidizing + diffusion hydrogen & quot;, the cold roll blank has been forged succesfully, and the percent of pass is up to 90. 5 %

    文摘:採用鋼包精煉爐冶煉、寬平砧大壓下量鍛造、 「正火+球化+擴氫」的熱處理工藝，成功製造了冷輥坯，合格率達90 . 5 。
  15. Abstract : this paper briefly introduces the method of testing the real sensitivity for eed and gives the data processing method in terms of the electrostatic critical ignition energy of conductive - powder eed conforming to logarithmic normal distribution

    文摘:簡要介紹了電火工品真實靜電感度的測試方法，以導電藥式電火工品靜電臨界點火能量服從對數正態分佈為基礎，給出了對應的數據處理方法。
  16. The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency

    在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下，利用棒材圓柱面測衰減系數法，分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況，得到的實驗結果是：對於40cr及38crmoal鋼， _ （低溫回火） （淬火） _ （高溫回火） _ （正火） ；對于gcr15simn鋼， _ （低溫回火） _ （退火） _ （高溫回火） _ （正火） ；且隨著頻率的提高，衰減系數均呈現增加的趨勢。
  17. Standard specification for pressure vessel plates, alloy steel, 9 percent nickel, double - normalized and tempered

    壓力容器用經二次正火及回火處理的含9鎳的合金鋼板標準規范
  18. Flat products made of steels for pressure purposes - part 3 : weldable fine grain steels, normalized ; german version en 10028 - 3 : 2003

    壓力容器用扁平鋼軋材.第3部分:經過正火處理的可焊細
  19. On the other hand, quite a number of practical systems with numerous dimensions may have some fast variables taking on singular impulse characteristic, such as electric power system, control system of rolling mill assembly, biochemical process, nuclear reactor, control system of airplane and rocket, and chemical diffused reaction, etc. so, it is important to study the problem of robust control of singular system i n the domain of control theory

    一般這些不確定性並非不可度量的，通常能給出這些不確定性大小的某種約束，魯棒控制理論正是處理系統模型具有不確定性的有效方法。另一方面，在大多數維數很大的實際系統中，都有呈現奇異攝動特性的快變變量，如電力系統，冷軋機的工業控制系統，生物化學過程，核反應堆，飛機和火箭系統，以及化學擴散反應等。
  20. In czochralski silicon crystals ( czsi ) through fast neutron irradiation, formation and conversion of defects were investigated using fourier transform infrared spectroscopy ( ftir ), positron annihilation technology ( pat ) and scanning electron microscope ( sem ). the results showed that fast neutron irradiation induced large quantity of metastable defects which can be the capture centers of positron, positron annihilation average lifetime of samples increased with increasing of irradiation dosage. positron annihilation average lifetime of irradiation samples through dosage up to 1 1018 n. cm - 2 tended to constant

    本文對直拉硅樣品進行了不同劑量的快中子輻照，在硅中引入大量的亞穩態缺陷，研究這些亞穩態缺陷的形成，並在較寬的溫度范圍內對輻照樣品進行了退火處理，研究退火后亞穩態缺陷的轉化及同硅中氧的相互作用，應用傅立葉變換紅外光譜技術（ ftir ） 、正電子湮沒技術（ pat ）和掃描電鏡（ sem ）進行了測試。
分享友人
分享到 Line

分享到臉書