正規坐標分析 的英文怎麼說

中文拼音 [zhēngguīzuòbiāofēnxī]
正規坐標分析 英文
normal coordinate analysis
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 規 : Ⅰ名詞1 （畫圓形的工具） instrument for drawing circles 2 （規則; 成例） rule; regulation 3 [機械...
  • 標 : Ⅰ名詞1 [書面語] （樹梢） treetop; the tip of a tree2 （枝節或表面） symptom; outside appearance; ...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  • 正規 : regular; standard; normal正規部隊 regular troops; regulars; 正規教育 regular education; proper ed...
  1. Applying the information extracted from numerous hydrographic data of field trials collected by h / hcs - 017, the first set of multi - beam swath bathymeter developed in china, a series of mosaic techniques have been carefully studied in this thesis, including digital terrain model building, statistical error analyzing, hydrographic data mosaicking as well as tides correction and projection of the earth coordinates. finally, standard digital sea - charts and three dimensional seafloor images are successfully developed that are consistent with hydrographic surveying principles

    本文利用我國第一臺h hcs ? 017型條帶測深儀的測量數據進行拼圖技術的研究，主要研究的內容有：利用分帶原理對深度數據進行潮汐修正，得到瞬時海面的深度數據；對測深數據進行誤差分析處理，去除野值；將多波束數據進行坐標變換及投影轉換后構建數字地理模型，進而根據海道測量規范繪制標準海圖。
  2. Some examples are given in this dissertation. first, the coordinate values of a group of discrete points on the cam profile are achieved by conventional design method which are then used as measured data of the cam profile. then the kinematic analysis of the cam mechanism is performed by the method developed in this paper

    本文以已知從動件運動規律的凸輪機構為例，利用正設計方法求出凸輪實際廓線一組離散點坐標值，並以此作為凸輪檢測數據，運用本文提出的分析方法進行運動反求，並將反求所得結果與理論結果加以分析比較。
  3. Abstract : variations of flow pattern, flow velocity in deep poo l and side bar, mainstream thread, and water surface, caused by excavation project, are investigated by two - dimensional mathematical model in an orthogonal curvili near coordinate system. the change of bed - load transport rate, and redeposition r ate are predicted. the influences of the excavation project on navigation are ana lyzed. grid - type and flat - type excavation alternatives are proposed and discuss ed

    文摘:採用正交曲線坐標系下的河道平面二維數學模型，研究了嘉陵江何家磧邊灘采砂后河道流勢、流態、灘槽流速、主流位置、水面高程及比降的變化規律，預測了采砂方案完成後卵石推移質輸沙率變化及其對航道的影響，並對格形開挖和平整開挖方案進行了比較分析
  4. A powerful tool of dynamical system analysis named normal form method is presented in this dissertation, and then it was used to analyze oscillation phenomena in interconnected power grids. using nonlinear coordinate transformation of normal forms, a fully described power system can be converted to an equivalent reduced order model, which can still use the conventional modal analysis of small signal stability problems

    論文將動力系統非線性分析的正規形理論應用於互聯系統低頻振蕩分析中，利用正規形方法的非線性坐標變換，將高階電力系統轉化為等價的低階系統，在保留非線性信息的同時，使其仍然可以使用常規小信號穩定研究的模式分析方法。
  5. This paper stated the application of parallel link mechanism in modern machine tools, set up the error analysis as to parallel link mechanism in the virtucal - axis machine tool, derived the double triangular error equations of parallel link mechanicsm in its horizontal posture, analyzed the linearity and non - singularity of the error equations, thus giving the normal splution to the horizontal posture error. the error distribution law is simulated as to the center line in the workplace, and the error distribution curves are drawn as well

    該文對並聯機構在現代機床上的應用作了論述，建立了虛擬軸機床並聯機構的一種誤差分析方法，應用坐標變換原理導出了雙三角並聯機構水平姿態時的誤差方程組；分析了誤差方程組的線性和非奇異性，給出了水平姿態時的位姿誤差正解；對工作空間中心線的誤差分佈規律進行了模擬，繪制了其誤差分佈曲線。
  6. Then the article specifies the control principle of the infrared sensor, the dust warehouse detection, the collision detection, the floating switch, the speedometer, the edge - walking detection, the keyboard, the liquid crystal display as well as the vacuum motor, the brush motor, the driver motor and etc. in the software design aspect, through analyzing the link between the bottom hardware and path coverage planning algorithm, it actualizes pid adjustment algorithm for the robot ’ s straight walking, the coordinate transformation and computation of speedometer ’ s return value, providing the basis for the route coverage algorithm

    然後，詳細說明了紅外傳感器，塵倉檢測，碰撞檢測，浮動開關，里程計，貼邊行走檢測、鍵盤、液晶顯示以及吸塵電機、毛刷電機、主動輪驅動電機等控制原理。在軟體設計方面，通過分析底層與路徑規劃演算法的銜接，實現了機器人直行pid校正演算法、里程計返回值的坐標變換及計算等演算法，為路徑覆蓋演算法提供依據。
分享友人
分享到 Line

分享到臉書