殘余熱 的英文怎麼說

中文拼音 [cányúrè]
殘余熱 英文
residual heat
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 余熱 : afterheat; waste heat
  1. Upon cooling, the thermal mismatch between residual silicon and quartz usually results in the fracture of the crucible.

    當冷卻時，殘余的硅和石英間的熱失配往往導致坩堝破裂。
  2. These stresses arise from the exothermic nature of the reaction during gelatin and cure.

    這種殘余應力系由凝膠和固化期間化學反應能放出的熱引起的。
  3. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  4. Through measuring residual swhirling flow field in the flue duct of a real boiler, and analysing layout features of front and back platen supe - heaters in large - scale tangential firing boilers, the flue gas energy distribution regularity in horizontal flue duct of tangential firing boilers has been studied

    摘要通過對實際鍋爐煙道煙氣殘余旋轉流場的測量及大型切圓燃燒鍋爐前、后屏過熱器的布置特點分析，研究了切圓燃燒鍋爐水平煙道煙氣能量的分佈規律。
  5. Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure

    文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致
  6. In metal matrix composites, thermal residual stresses will arise due to get ( coefficient of thermal expansion ) mismatch between matrix and fiber during cooling

    在擠壓鑄造的金屬基復合材料中，由於基體和纖維的熱膨脹系數相差很大，所以在制備過程中由高溫（工藝溫度）冷卻至室溫時復合材料中會有熱殘余應力產生。
  7. Residual stress analysis of thermal barrier coatings

    熱障塗層的殘余應力分析
  8. Residual stress and damage evolution in tbcs by optical method

    熱障塗層氧化殘余應力大小與演化過程測試
  9. New geological logging technical method of pyrolysis gas - chromatogram and gas chromatography is briefly introduced to evaluate light crude oil zone and residual oil zone here, involved in geology, geochemical pyrolytic parameter and geophysical method

    本論文主要是利用熱解色譜、氣相色譜等地質錄井新技術評價手段，結合地質、地球化學及地球物理方法，針對輕質油層，殘余油水層識別對象開展研究。
  10. For more years, the welded members of steel structure are more popular than the rolled ones in china, but as is well known, the mechanical performance of welded members are effected by many factors : such as the material property of plates, the heat effect during welding process, the residual stress, the weld techniques and so on

    一直以來我國使用的鋼結構構件以焊接為主，軋制的較少。眾所周知，焊接構件的力學性能將受諸多因素的影響，如焊接板材的材性是否一樣、焊接產生的熱影響以及焊接殘余應力和焊接工藝等。
  11. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  12. According to the chemical experimental data of residual organic carbon content, kerogen carbon isotope, aliphaltic gas chromatography mass spectrometry of 67 outcrop specimens in the baise basin, the authors analyse the geochemical characteristics of the type and the maturation of organic matter in the lower triassic - devonian source rock

    根據百色盆地周緣大量露頭樣品的殘余有機碳含量、乾酪根碳同位素、飽和烴色譜及色質等地球化學實驗數據，分析了下三疊統泥盆系海相烴源巖的有機質豐度、類型、熱演化程度。
  13. Because there are many kinds of matrixes in titanium matrix composite, we select some typical ones as investigated subject in many titanium alloys or titanium aluminide intermetallics, and then simulate the distribution of thermal residual stresses under the appropriate composites fabrication and heat treatment parameter. we not only hope to seek better titanium matrix, but also discover the relationship between the material properties and the thermal residual stresses, and then provide some theoretical guidance for the selection of the matrix in titanium matrix composites

    鑒于當前鈦基復合材料中鈦基體的多樣性，我們將在各種類型的鈦合金和鈦鋁金屬間化合物中，挑選出較為典型的作為研究對象，利用本文得到的較為理想的復合材料加工和熱處理工藝參數，逐一模擬它們的殘余熱應力，找到殘余熱應力分佈較為理想的鈦基體，並且，希望能夠尋找到材料性能與熱殘余應力的相互關系，為鈦基復合材料基體的選擇提供一定的理論指導。
  14. A short fiber reinforced composition and interface residual stress analysis

    短纖維增強復合材料纖維和界面層殘余熱應力分析
  15. The results of fe simulation shows that the mental package made abroad has lower thermal stress and higher reliability during working and manufacturing process than that made in china. it is mainly because that the two packaging structures were manufactured in different forming processes : one was punched and the other was brazed

    有限元計算的結果表明，採用沖壓一次成型的國外封裝外殼比採用異材壓焊的國產封裝外殼的工作熱應力和製造殘余熱應力要小很多，具有更高的可靠性。
  16. In order to lower residual heat on the surface of the block, the cooling mans is installed in interwall of the block. the wortle is soaked in cooling watr to reduce its working temperature

    捲筒內壁設備有冷卻噴水裝置，以降低拉撥后的鋼絲傳道線捲筒表面的殘余熱量，拉撥模具的工作溫度。
  17. The residual thermal stress of the tz - 3y20a / mo multiplayer composite has been forecasted by finite element method

    Marc有限元軟體計算了疊層材料的殘余熱應力。
  18. Moreover, the technique of elements deactivating and activating was used in fe analysis to simulate the manufacturing process of the packaging structures. the residual thermal deformations and stresses during the process were obtained

    另外採用有限元計算中的單元死活技術成功模擬了封裝結構的製造過程，由此得到在製造過程中所產生的殘余熱變形和應力。
  19. The outcome indicates that the graded composite can effectively reduce the residual thermal stress. when the distribution p is 1. 2, the relaxation effect is m ost conspicuous and up to 60 %. finally, the atio5 / al2o3 functionally graded material is fabricated by the power stacking - method based on the fabrication technique and structure design discussed above

    計算結果表明，通過梯度復合可以有效地緩和梯度材料制備過程中所產生的殘余熱應力，當梯度材料分佈指數p值為1 . 2時，熱應力緩和的作用最顯著，緩和效果達60 。
  20. It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials

    研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。
分享友人
分享到 Line

分享到臉書