比例反應器 的英文怎麼說

中文拼音 [bǐlìfǎnyīngqì]
比例反應器 英文
scale reactor
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 反 : Ⅰ名詞1 （方向相背） reverse side 2 （造反） rebellion 3 （指反革命、反動派） counterrevolutionari...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 比例 : 1. （長度上縮小和放大的倍數） scale; scaling 2. （比率） proportion; ratio; proportionality
  1. According to the test data and the technological and economic comparison between a process of mbr and a conventional process for reclaimed water treatment, it is concluded that the investment and operating cost of mbr is the same as the conventional process basically. the advantages of mbr are on the land occupation, maintaining, effluent quality and automatic control. the process is specially suited to hotel, restaurant and public buildings because they usually have less useable land, bigger fluctuation of sewage rate, understaffed group of management and higher quality demand of effluent

    根據取得的試驗數據，通過對膜生物反應器設計實例與傳統工藝設計相比較，在進行技術經濟分析后認為，膜生物反應器處理工藝在投資與運行成本上與傳統工藝基本持平，而在佔地、維護管理、處理水質、自動化程度等方面比傳統工藝有較大優勢，特別適合中水設施場地不足、原水波動大、管理人員少、出水水質要求高的賓館、飯店和公共建築。
  2. The first - order perturbation method correct for forcing decoupling method based on perturbation theory is put forward to decrease error ; iii. the complex modal method is introduced into analysis of non - classical damping systems to eliminate error of forcing decoupling method, and improve the complex modal response spectrum, which can apply to design of non - classical damping systems ; iv. for exerting the energy dissipation capability of each device, a two - step optimum method, whose controlling function is extremum expectation of interbedded displacement, is put forward to optimize the number and position of device ; v. the problem of iterative method applied to analyze energy dissipation systems is indicate, and give some primary advice based on pilot study

    為改善上述缺點，本文進行了以下的研究工作：在忽略耗能器附加質量的基礎上，推導出適用於耗能減震結構的攝動法，減少振型分解法在迭代計算過程中的工作量，加快計算速度；針對運動方程的強行解耦所產生的誤差，根據攝動法原理，對其進行一階攝動修正；為消除強行解耦振型分解法用於非比例阻尼結構分析時產生的誤差，引入狀態空間對系統進行復模態分析，並改進了基於復模態理論的、適用於非比例阻尼結構設計的雙反應譜方法；對于耗能器的數量和位置優化進行了一些探討和研究。
  3. Through simulation and calculating the four models, the influence on proportion coefficient, integral time constant, derivative time constant and partial feedback coefficient for system performance is analyzed. the ideal reference value of every parameters and step respond curves are given. the simulation result may be used as reference for making analogue controller or digital controller

    通過對這四種模型的模擬研究，分析了各模型中比例系數、積分時間常數，微分時間常數及局部反饋系數對系統性能的影響，並給出了各參數較為理想的參考值及階躍響應曲線，模擬結果對製作模擬控制器及數字控制器有一定的借鑒作用。
  4. Finally, some fault diagnosis cases about rolling contact bearing, oil pumping unit, especially twin - screw extruder are provided to demonstrate the establishment of multi - fault classifier. the property between c - svc and - svc and two kinds of agorthm between “ one - against - one ” and “ one against the other ” are made a comparison respectively and the simulation results are given. meanwhile, the differences of generalization capability between svm and nn on the condition of small - sample are reflected when nn is applied to the same samples

    文章主要介紹了兩類故障分類器和多故障分類器的建立，比較了c -支持向量分類機和-支持向量分類機的性能以及「成對分類」和「一類對余類」兩種多類分類演算法的優缺點，同時，將神經網路應用在同樣的實例上，反映了支持向量機與神經網路在少樣本情況下的推廣性能差異。
分享友人
分享到 Line

分享到臉書