比例檢波器 的英文怎麼說

中文拼音 [bǐlìjiǎnbōqì]
比例檢波器 英文
ratio detector
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 波 : Ⅰ名詞1 （波浪） wave 2 [物理學] （振動傳播的過程） wave 3 （意外變化） an unexpected turn of even...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 比例 : 1. （長度上縮小和放大的倍數） scale; scaling 2. （比率） proportion; ratio; proportionality
  1. The bias magnetic field of the bias coil driven by bias current and small signal test current, results in the induced signal of the control coil. the terminal voltage of the control coil is detected by the test circuit. then the signal containing the information of rotor displacement is obtained, from which we can get the dc voltage signal proportional to the rotor displacement through half - wave rectification circuit and low pass circuit. this dc signal is put into a pid controller to get the control signal of the rotor displacement

    偏置測試電路向偏置線圈輸入偏置電流和小信號測試電流，兩者產生的偏置磁場在控制線圈產生感應信號，檢測電路檢測控制線圈端電壓並提取含有轉子位移信息的電壓信號，該信號經半波整流電路和低通濾波電路后得到與轉子位移成正比例的直流信號，再由pid控制器轉換為轉子位移的控制信號，最後控制信號輸入功放電路產生控制電流，實現閉環控制。
  2. This paper simulates the effect of voltage fluctuation inspection through the tool of matlab. and proves the filters ' s stability. in the part of self - checkout, pi ( proportional integral ) control arithmetic is put forward to check the gain k and the calculated results show the method ' s effectiveness. then many comparements toward pst are done in different realization methods such as different interpolation points classification number and sample frequency. though simulation and calculation we can see the designed flicermeter can meet our country ' s standands

    文中利用matlab對電壓波動的檢測效果進行了模擬；並對涉及到的濾波器的穩定性做了證明；在自校驗部分提出了將pi （比例、積分）演算法用於數字濾波器增益k值的確定，取得了不錯的效果；然後分別從取不同插值點、不同分級數和不同采樣頻率這幾個方面出發，對計算出的p _ （ st ）值進行了比較。
  3. Firstly, the theory and the architecture of hardware system are described, secondly, the steps of the signal processing are discussed in detail. based on the experiments and the characteristics of the signal, we pre - process the signals with band - pass filter, proportional amplifier and coherent demodulator. after sampling and analysis doppler information, we display the final results distinctly to alarm in time

    然後，結合系統中各主要部分的任務，詳細介紹了信號處理的各個步驟：通過實驗比較，並結合接收信號的特點，選用帶通濾波器、比例放大器、相干檢波等技術對信號進行預處理；然後對獲得的多卜勒信息進行采樣和頻譜分析；最後，用比較直觀的形式顯示數據結果，以及時準確地告警。
分享友人
分享到 Line

分享到臉書