高壓燃燒 的英文怎麼說

中文拼音 [gāoyāránshāo]
高壓燃燒 英文
high-pressure combustion
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 壓 : 壓構詞成分。
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 高壓 : 1 （殘酷迫害; 極度壓制） high handed 2 [氣象學] （高氣壓） high pressure3 （高電壓） high tension...
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing

    文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力
  2. Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading

    文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點
  3. Since cordite burns at a greater rate at a higher pressure a relief valve must be used to allow generated gas to escape to atmosphere at times when the demand is low.

    因為柯達火藥在較高的壓力下以較高的速度燃燒，所以必須使用一個溢流閥，以便當用氣少時，能讓所產生的部分氣體排到大氣中去。
  4. Long - hole and geometrical proportion type of mixing unit is finally adapted in lpg supply system, and power and torque output of lpg engine are improved by increasing compression ratio, and ignition characteristic is tried to adjusted to satisfy engine performance. meantime emission performance and noise level of lpg engine at full - throttle and other various part - throttle operations are tested and compared with former gasoline engine. ( 3 ) it is verified by engine dyno tests that lpg engine has better synthesized performance at aspects of power and torque, fuel economy, as well as emission than former gasoline engine

    選擇了等比例長孔式混合器控制空燃比；通過提高壓縮比來彌補動力性的損失；以動力性為主控目標，對最大功率點、最大扭矩點、中等轉速、最低轉速點所對應的發動機轉速做了點火特性的調節；通過空燃比的合理控制，直接改善發動機的動力性、經濟和排放指標；作為對缸內燃燒過程的理論分析，進行了燃燒特性的實驗測試；對原汽油機和新開發的液化石油氣發動機，進行了外特性和部分負荷特性以及怠速的排放及噪聲對比性測試。
  5. A heating unit in the basement of a house burns gas to heat air or water, which is then forced through the house or building to raise it ' s temperature

    居於樓房地下室的一個供熱裝置通過燃燒氣體釋放熱量來給水和空氣加熱，加熱的水或空氣則靠壓力運送到樓房或大樓來提高它的溫度。
  6. Ionic liquids are extensively studied in areas of chemical synthesis, separation technology, electrochemistry and material processing due to their unique properties such as high electrical conductivity, high thermal stability, low measurable vapor pressure and incombustibility

    摘要由於離子液體具有電導率高、熱穩定性好、蒸氣壓低、不燃燒等優良性質，越來越多地應用於有機合成、分離、電化學和材料加工等領域。
  7. In the article, the originator worked out the mechanism of magnesium - base alloys catching fire ; analyzed briefly the influence of the temperature, the heating velocity and the pressure of oxygen in the atmosphere on the lumps and scraps of pure magnesium ’ s catching fire, and designed a practical method to measure the kindling temperature of the lumps and scraps of pure magnesium precisely, with which the initial quantization of kindling temperature can be realized

    本文圍繞鎂合金阻燃技術的開發作了許多基礎性的研究工作，通過分析大量的相關文獻和試驗結果，初步得出了塊狀鎂和鎂屑的燃燒機理，簡要分析了溫度、升溫速度、環境中氧的分壓對塊狀鎂和鎂屑的起火燃燒所產生的影響。設計出了精確度高、實用性強的塊狀鎂和鎂屑的燃點測試方法，使塊狀鎂和鎂屑的燃點得到初步的量化。
  8. The investigation has declared that the fuel injection with bq fuel pump had higher injection pressure, bigger fuel supply rate and shouter fuel supply duration, which would cause the fuel injection quantity and the fule - air mixture to increase during ignition delay period, the pre - mixed combustion to become acutely, and finally result in increased power levels of noise

    研究表明，裝配bq噴油泵，噴油系統的噴油壓力較高，供油速率較大和供油持續時間縮短，使得滯燃期的噴油量增加，滯燃期內形成的可燃混合較多，預混燃燒劇烈，導致整機噪聲聲功率級增加。
  9. The question about burning method existing in spraying high pressure steaming in chamber is analyzed. the principle and character of auto supplying water, additive, steaming and combustion - support technology are introduced, also the economic benefit is analyzed

    分析了傳統爐膛內噴射高壓蒸汽燃燒方法存在的問題，介紹了鍋爐全自補水加劑注汽助燃技術的機理、特點。
  10. The results indicate that with the coefficient of residual oxygen being less than 1 or around 1, when the fuel is injected into the combustor at the same combustor pressure, the higher the combustor temperature is, the less the coefficient of residual oxygen is when auto - ignition occurs ; when the fuel is injected into the combustor at the same combustor temperature, the larger the combustor pressure is, the less the coefficient of residual oxygen is when auto - ignition occurs ; when the fuel is injected into the combustor at the same combustor temperature and pressure, the bigger the coefficient of residual oxygen is, the more easily auto - ignition occurs

    研究結果表明，當推進劑處于余氧系數小於1或略大於1時，在燃燒室壓力相同的情況下噴入燃料，燃燒室溫度越高，可自燃的余氧系數越小;在燃燒室溫度大致相同的情況下噴入燃料，燃燒室壓力越高，可自燃的余氧系數越小;在燃燒室溫度、壓力大致相同的情況下噴入燃料，余氧系數越高，自燃發生的可能性越大。
  11. Analysis on the relationship between rise rate of cylinder pressure and combustion noise

    車用柴油機氣缸壓力升高率與燃燒噪聲的關系
  12. In the range of flight mach number mo = 3 ~ 7, in order to take the advantage of ramjet and scramjet, a fix - shaped dual - mode scramjet, in which both subsonic and supersonic combustion can be obtained, is used for hypersonic vehicle

    在飛行馬赫數m _ = 3 - 7的范圍內，為充分發揮沖壓發動機的性能優勢，高超聲速飛行器採用了既能在亞聲速燃燒模態，又能在超聲速燃燒模態下工作的固定幾何形狀的雙模態沖壓發動機。
  13. It ' s the first time to explore the combustion characteristics of lpg / diesel mixing fuel engine, and find that, with the change of load and rotation, the changing trend of the ignition delay period of e10 mixing fuel is almost as identical as that of the diesel, but that of e30 mixing fuel is very different. comparing with diesel, the combustion of e10 is improved slightly, but that of e30 greatly changes ; the maximum eruptive pressure decreases ; the maximum pressure increase rate decreases ; the highest releasing heat rate increases ; the highest combustion temperature falls ; the ignition delay period extends

    結果表明: e10混合燃料與柴油的著火滯燃期隨負荷和轉速的變化趨勢基本一致; e30混合燃料與柴油則有所不同; eio混合燃料發動機的燃燒與純柴油相比，略有改善; e30混合燃料的燃燒特性發生明顯的變化，最高爆發壓力下降，最大壓力升高率減小，最大燃燒放熱率增大，最高燃燒溫度下降，滯燃期延長。
  14. Based on the theoretical analysis and design practice in successful development of allway desiel engine in china, the design concepts of key parts and components of engine, in particular the cylinder block and cylinder head, are analyzed for meeting the requirements for high performance and low emission as well as normal and reliable operation of diesel engine for medium and heavy commercial vehicle under high combustion pressure and high thermal load

    摘要結合我國自主開發的「奧威」發動機在設計工作中的理論分析與實踐，就低排放中重型商用車柴油機在開發工作中為滿足高性能、低排放的要求及在高燃燒爆發壓力和高熱負荷下正常可靠地工作，對發動機的關鍵零部件，尤其是缸蓋與缸體的設計概念進行了分析。
  15. Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained

    本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。
  16. A quick spectroscopic diagnostic system for the flame temperature is set up in this paper. it consists of an optic imaging system, a scanning system, a dispersive system, a photoelectricity conversion cell, operational amplifiers, a computer - based data collection system and a data processing. the temperature profile varying with the time can be quickly measured by this system

    目前光學診斷由於其相應快、精度高，屬于非接觸式測量手段，在研究中得到越來越多的應用，這里要介紹的就是本文中建立的一套光學診斷系統，它由高壓燃燒室、旋鏡掃描儀、旋鏡控制器、小型光柵攝譜儀、光電轉換裝置，微弱信號放大器以及數據採集系統組成。
  17. Methods of test for petroleum and its products - determination of sulfur - high pressure combustion method

    石油及其產品的試驗方法.硫的測定.高壓燃燒法
  18. Based on correctly describing high pressure fuel injection spray, a quasi - dimensional combustion model for forecasting performance and emission of high pressure common rail diesel engine is established

    在正確描述高壓燃油噴霧的基礎上，建立了一個能預測高壓共軌柴油機性能和排放的準維燃燒模型。
  19. The experimental investigations were first conducted on diesel spray wall - impingement mixing process with or without a bump on a flat wall and in a combustion chamber by means of plif method in the self - made constant volume combustion spray simulation set - up which can reproduce the typical working conditions and high - pressure fuel injection of modern diesel engines. the simulation computation of a cfd code about them was then carried out

    首先在自行研製的、可以模擬現代柴油機典型工作環境及高壓燃油噴射特性的定容燃燒噴霧模擬裝置上用片狀激光誘導熒光法（ plif ）對平壁上、燃燒室內不設置和設置bump的柴油噴霧撞壁混合過程進行了試驗研究，然後又用cfd多維數值分析軟體對其進行了模擬計算。
  20. Combustion with releasing heat effectively in supersonic flow is one of the most important, as well as the most difficult, technologies in researching and developing supersonic combustion ramjet

    超音速流動狀態下的高效燃燒過程是研製超燃沖壓發動機最重要也是難度最大的關鍵技術之一。
分享友人
分享到 Line

分享到臉書