氣力噴霧 的英文怎麼說

中文拼音 [qìlìpēnwù]
氣力噴霧 英文
air spraying
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
  • 氣力 : effort; energy; physical strength
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  3. With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator

    本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。
  4. Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement

    摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。
  5. Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water - air ratio through a single factor experiment

    通過單因素試驗定量分析了噴嘴孔徑、噴水初溫、噴水壓力以及水氣比對霧化加濕的具體影響。
  6. ( 2 ) in this paper, the author summarized the working principle, the superiority and the limitations of a few main kinds of classical sprinkler systems ; put emphasis on the importance of a few key points which is relevant to the function of the system, such as the choosing of sprinkler and it ' s fixing, the automatic checking function of water pump, the layout of alarm valve, especially the choosing of sprinkler and it ' s fixing ; looked through the feasibility of which we used water instead of gas by water mist especially finely divided water mist fire - extinguishing technique

    展望了水噴霧技術特別是細水霧技術進行以水代氣滅火的可行性。 （ 3 ）針對工程設計中最復雜，工作量最大的部分-系統水力計算部分，在規范的基礎上，基於excel電子表格，提出了經濟流速的范圍，提供了一套行之有效的設計計算方法，同時，對屋頂水箱和增壓泵的設置這一難以解決的問題發表了見解，既確保了自動噴水滅火系統初期快速滅火、控火的性能，又節省了大量的設計工作時間。
  7. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  8. Experiment shows that when the gas hydrate is obtained by spray, its induction time is generally shorter, its phenomenon is not obvious, setting of initial temperature and pressure with an autoclave has certain influence on induction time, but not obvious, water resources and spray nozzle have bigger influence on the induction time

    試驗表明，噴霧方式制取天然氣水合物時，誘導時間普遍較短，誘導現象不明顯；反應釜設定初始溫度和壓力對誘導時間有一定影響，但不是很明顯；水源和霧化噴嘴對誘導時間的影響較大。
  9. The police will use gotacha spray at the bad guys to incompetennt, the spray allows the police to get the greatest result with the least physical effort

    警方將此噴霧式噴罐對著壞人噴? ，被噴到將會四肢無力，讓警方用最少的力氣達到最高效率。
  10. The fog is produced by a device ( thermal fogger ) that uses heat to break up the chemical into very small droplets ( usually in 5 - 30 micron diameter range ) which will disperse in the air

    熱噴霧是經由一特製裝置（熱噴霧器） ，利用熱力把化學液體化為微細霧滴（直徑通常由5至30微米不等）散播並懸浮於空氣中。
  11. When the mosquitoes in flight come into contact with the chemical droplets floating in the air, they will be killed. however, its ability to penetrate dense foliage or obstacles is not as good as that of the thermal fogging

    飛行中的蚊子若接觸懸浮在空氣中的化學霧滴，就會死亡。不過，冷噴霧滲透枝葉茂盛或多障礙物件地方的能力不及熱噴霧。
  12. Considering the water spraying can effectively increase the contact area between gas and water and promote the hydrate production rate, a batch reactor with water spraying was built in order to experimentally investigate the forming performance of natural gas hydrate, the system ' s state parameters ' variation and its effect on induced time of initial pressure and water temperature

    摘要考慮到水的霧化可以有效提高氣水接觸面積，有助於提高水合物生產速率，設計和建造了一個半間歇式霧流強化水合物實驗裝置，用於探索和揭示噴霧強化天然氣水合物制備過程的基本特性，包括制備水合物的形態特徵，形成過程中參數的變化規律，以及系統初始壓力和初始水溫度對形成過程誘導時間的影響。
  13. ( 1 ) the cfd model for the pulse combustion spray drying process. the computational fluid dynamics ( cfd ) based on the two - phase flow theory was employed in this paper, which used the standard k - e model and the particle trajectory model to simulate the gas - particle flow in the drying chamber. the momentum, heat and mass transfer regarding both gaseous and particulate phases during the spray drying inside the drying chamber was also revealed

    為解決這一難題，本文利用氣體一顆粒兩相流理論和計算流體力學（ cfd ）技術，建立了更符合實際噴霧乾燥過程的數學模型即噴霧乾燥的cfd模型，並進行了脈動燃燒噴霧乾燥過程模擬，其主要內容如下： （ 1 ）建立了脈動燃燒噴霧乾燥的cfd模型該數學模型建立在氣體一顆粒兩相流基礎之上，用標準k -模型預測乾燥室內的氣體湍流運動過程，顆粒軌道模型追蹤乾燥室內顆粒群的運動軌跡，熱質傳遞模型描述空氣和液滴的熱質傳遞過程。
  14. The unstable gas stream is characterized by oscillations with transient velocities of about + 100 m / s and frequencies from 50 - 200h /. the enhanced mixing and transport processes lead to a highly efficient moisture evaporation rate during pulsating spray drying. the computational fluid dynamics ( cfd ) method was used for the analysis and investigation of flow, temperature and humidity fields in a pulsating flow spray - drying chamber

    長期以來，對噴霧乾燥過程進行了各種試驗和模擬研究，但這些研究並不能揭示噴霧乾燥室內氣體運動狀態，顆粒群的運動軌跡和各種熱力學參數分佈信息，常規的測試手段又很難測得，而這些參數分佈信息對乾燥器沒計和過程優化具有重要指導作用。
  15. Besides, the aerosol spray is packed in a pressurised container that may explode if exposed to excessive heat

    另外，噴霧劑產品內含壓縮氣體，罐內壓力頗高，如果過度受熱，則可能引致爆炸。
  16. In this dissertation, the author summed up the muti - technique in fluid dynamics, heat and mass transferring, mechanical designing and computational technique and studied the conventional pressure spray dryers with different air disperse structure and outlet equipment, at last put forward the theme i. e. the study on combined spin - flow pressure spray drying technology, the main contents were as follows : ( 1 ) the combined spin - flow pressure nozzle was designed whose novel structure has no report at present, and the structural designing parameters were obtained through analyzing the physical characteristic of materials and distribution of particles

    本文總結了國內外在壓力噴霧乾燥裝置的研究應用狀況，並分析了現有噴霧乾燥裝置設計方面的優缺點，運用流體力學、空氣動力學、傳熱傳質學、機械設計和計算機技術等多學科知識，綜合研究了傳統壓力噴霧乾燥系統的單噴嘴霧化裝置在併流、逆流以及混流乾燥中的應用和噴霧乾燥塔的不同布風裝置以及出風裝置的設置情況等，提出了新型旋流式組合壓力噴霧乾燥技術並對此進行了研究，其主要內容包括： （ 1 ）本文創造性地設計出旋流式組合壓力噴嘴的基本結構，並通過對料液的物化特性研究分析以及顆粒度的分佈要求，給出了噴嘴的不同結構設計參數。
  17. Moreover, the secondary wall - impingement distance should be properly reduced in order that the bump play a part in the formation of lean mixture with the increase of environmental pressure or density owing to both the increase of air entrainment, momentum losses and the decrease of the spray tip velocity and penetration

    而且當壓力或密度較高時，由於噴霧的空氣卷吸量及動量損失增大，貫穿速度降低及貫穿距減小，為使bump發揮作用，應適當減小二次撞壁距離。
  18. With in - air and spray pressure double adjustment, double protection with over temperature alarming and power off

    進氣壓力及噴霧壓力雙重調節，超溫報警並切斷加熱電源，具有雙重保護。
  19. Standard test method for effectiveness of aerosol and pressurized spray insecticides against cockroaches

    氣霧及噴霧殺蟲劑殺蟑螂效力的試驗方法
  20. Standard test method for effectiveness of aerosol and pressurized space spray insecticides against flying insects

    氣霧及噴霧殺蟲劑殺飛行昆蟲效力的測試
分享友人
分享到 Line

分享到臉書