氣壓噴霧 的英文怎麼說

中文拼音 [qìyāpēnwù]
氣壓噴霧 英文
air blast atomizing
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 壓 : 壓構詞成分。
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
  • 氣壓 : [氣象學] pressure; atmospheric pressure; barometric pressure; gas pressure; air pressure
  1. General specifications for impulse air pressure spray gun

    脈沖氣壓噴霧水槍通用技術條件
  2. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  3. By analyzing and predicting the microclimate in greenhouse in typical weathers, the conclusions are that high temperature with low humidity weather and high temperature with high humidity appear one after the other. the measures are proposed as the followings : to the former, it should be taken to decrease the temperature with soppy shade - fan or spray inside or outside ; to the latter, it should be taken to enlarge the ventilation area, to fit spray apparatus at the top of roof outside, to adopt havelock outside instead inside, to coat the roof white, etc

    通過對典型天氣下溫室小氣候變化規律分析和預測，其結論是：從7月中旬到8月中下旬，室內相繼出現高溫低溫和高溫高濕天氣，建議分別採取的適宜措施是：濕簾-風機降溫、高壓噴霧降溫、屋頂噴淋降溫和增大屋頂通風窗的通風面積、安裝屋頂噴淋（霧）設備、改溫室內遮陽為外遮陽、塗白溫室屋頂等。
  4. The coatings are sprayed onto the components being analyzed by using aerosol cans or compressed-air spray guns.

    塗料是用按鈕噴霧罐或壓縮氣噴槍噴到所要分析的零件上去的。
  5. With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator

    本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。
  6. Compressed air atomization

    壓縮空氣噴霧法
  7. A vacuum interface used for atmospheric pressure ionization ion source was designed to couple with an orthogonal - injection electrospray ionization time - of - flight mass spectrometer ( tofms )

    摘要研製了一種大氣壓離子源真空介面，並已將其用於自製高解析度垂直引入式電噴霧電離飛行時間質譜儀。
  8. The main products of our company : series of mining emulsion pump station, series of electric haulage shearer, sparying pump station, series of mining flame - proof vacuum / air electromagnetic starter, series of mining vacuum / air feeding switch, series of mining fame - proof and natural - safe. type ac soft starter, series of hydraulic stand valve and pipe system, high flow rate quick - moving valve, the new product nearing into market - the hydraulic support electric - control system, mining electric drill, hydraulic valve test table, electric performance test table

    公司主導產品為：系列電牽引採煤機、系列礦用乳化液泵站、噴霧泵站、礦用隔爆兼本質安全型交流軟起動器、系列礦用隔爆真空、空氣電磁起動器、系列礦用真空、空氣饋電開關、系列液壓支架閥類及管路系統、大流量快速移架閥、即將投入市場的新產品? ?液壓支架電液控制系統、煤電鉆系列、液壓閥試驗臺、電性能試驗臺等。
  9. Based on the induction phenomenon caused in gas hydrate formation, the influential rules of its gas entrance mode, temperature, pressure, water resources and nozzle on the induction time are analyzed by means of experimental study on the induction time of gas hydrate formation obtained by water spray and enhancement

    摘要以氣體水合物形成過程中的誘導現象為基礎，通過對噴霧強化方式制取天然氣水合物的誘導時間進行試驗研究，考察分析了系統進氣方式、溫度、壓力、水源及噴嘴等因素對誘導時間的影響規律。
  10. Quantitatively analyses the concrete influences on atomizing humidifying performance of the nozzle aperture, initial temperature and the pressure of spray water and the water - air ratio through a single factor experiment

    通過單因素試驗定量分析了噴嘴孔徑、噴水初溫、噴水壓力以及水氣比對霧化加濕的具體影響。
  11. He said that the most commonly found dangerous goods inside baggage at hkia were cigarette lighters, perfume or toiletry items, aerosols or compressed gases, fireworks, gas torches, and household items such as adhesives, polishes, bleach and drain cleaner

    他表示，在香港國際機場處理的行李內，經常發現的危險品包括打火機、香水或梳妝物品、噴霧罐或壓縮氣體、煙花、以氣體燃點的點火器和接合劑、擦亮劑、漂白劑和溝渠去污劑等家居用品。
  12. Then diesel fuel oil is injected or sprayed into the cylinder at the end of the compression stroke.

    然後在壓縮沖程即將結束時，柴油燃料被噴射或被噴霧進入氣缸。
  13. The works would include creation of negative pressure gradient in wards, provision of 100 per cent fresh air supply and dilution of bioload in sufficient air change rates, installation of high efficiency particulate air filters to filter out droplets and aerosols, and the provision of en - suite toiletshower facilities in ward cubicles where building structure and existing building services installations permit

    工程將包括在病房內製造負氣壓坡度；以足夠的換氣率，供應百分之百的新鮮空氣以及稀釋空氣中的微生物含量；安裝高效能空氣粒子過濾器，過濾飛沫和噴霧；以及在建築結構和現有屋宇裝備許可的情況下，在病房單間內提供獨立洗手間和淋浴設施。
  14. ( 2 ) in this paper, the author summarized the working principle, the superiority and the limitations of a few main kinds of classical sprinkler systems ; put emphasis on the importance of a few key points which is relevant to the function of the system, such as the choosing of sprinkler and it ' s fixing, the automatic checking function of water pump, the layout of alarm valve, especially the choosing of sprinkler and it ' s fixing ; looked through the feasibility of which we used water instead of gas by water mist especially finely divided water mist fire - extinguishing technique

    展望了水噴霧技術特別是細水霧技術進行以水代氣滅火的可行性。 （ 3 ）針對工程設計中最復雜，工作量最大的部分-系統水力計算部分，在規范的基礎上，基於excel電子表格，提出了經濟流速的范圍，提供了一套行之有效的設計計算方法，同時，對屋頂水箱和增壓泵的設置這一難以解決的問題發表了見解，既確保了自動噴水滅火系統初期快速滅火、控火的性能，又節省了大量的設計工作時間。
  15. Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors

    諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3
  16. Experiment shows that when the gas hydrate is obtained by spray, its induction time is generally shorter, its phenomenon is not obvious, setting of initial temperature and pressure with an autoclave has certain influence on induction time, but not obvious, water resources and spray nozzle have bigger influence on the induction time

    試驗表明，噴霧方式制取天然氣水合物時，誘導時間普遍較短，誘導現象不明顯；反應釜設定初始溫度和壓力對誘導時間有一定影響，但不是很明顯；水源和霧化噴嘴對誘導時間的影響較大。
  17. Water injection system includes pulverization system and controlling system of water quantity. pulverization system includes air resource, water resource and gas - mist nozzle ; controlling system of water quantity includes booster, controlling circuits. water quantity is decided by hydraulic pressure and gas pressure

    噴水系統包括霧化系統及水量控制系統，其中霧化系統包括空氣源（空氣壓縮機） 、水源（加壓水）及氣?霧噴嘴；水量控制系統包括比例調壓閥、控制電路部分。
  18. Considering the water spraying can effectively increase the contact area between gas and water and promote the hydrate production rate, a batch reactor with water spraying was built in order to experimentally investigate the forming performance of natural gas hydrate, the system ' s state parameters ' variation and its effect on induced time of initial pressure and water temperature

    摘要考慮到水的霧化可以有效提高氣水接觸面積，有助於提高水合物生產速率，設計和建造了一個半間歇式霧流強化水合物實驗裝置，用於探索和揭示噴霧強化天然氣水合物制備過程的基本特性，包括制備水合物的形態特徵，形成過程中參數的變化規律，以及系統初始壓力和初始水溫度對形成過程誘導時間的影響。
  19. Besides, the aerosol spray is packed in a pressurised container that may explode if exposed to excessive heat

    另外，噴霧劑產品內含壓縮氣體，罐內壓力頗高，如果過度受熱，則可能引致爆炸。
  20. The optimal parameters of making high silicon content aluminum alloys is : spray height is 220 - 230mm, spray angle is 30 ? the scanning velocity of atomizer is 30mm / s, the original offset of the substrate is 30mm, rotation velocity of the substrate is 120rpm, spray gas pressure is l. ompa, the diameter of the delivery tube is 3. 6mm, the drawing velocity of the substrate will be adjusted on - line with a plc on the basis of the spray

    通過對多層噴射沉積原理及工藝參數的研究，得出制備al - 22si - 3cu - 1mg合金的最佳工藝參數為：噴射高度為220mm - 230mm ，基底轉速為120rpm ，霧化器掃描速度為30mm / s ，基底下降轉速依據噴射情況由智能控制器進行實時調整，噴射角度為30 ，初始偏心距為30mm ，導流管直徑為3 . 6mm ，霧化氣壓為1 . 0mpa 。
分享友人
分享到 Line

分享到臉書