氣流混和機 的英文怎麼說

中文拼音 [qìliúhúnhéjī]
氣流混和機 英文
aeromix
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 混 : 混形容詞1. （渾濁） muddy; turbid2. （糊塗; 不明事理） foolish; stupid
  • 和 : 和動詞（在粉狀物中加液體攪拌或揉弄使有黏性） mix （powder） with water, etc. : 和點兒灰泥 prepare some plaster
  • 機 : machineengine
  • 氣流 : 1 [氣象學] air current; airflow; wind current; airstream2 [語言學] breath氣流紡紗 open end spinni...
  1. Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing

    文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力
  2. As we know, inverse techniques make blade ' s profile well compatible with its surface velocity distribution, however, they give designers big challenges that the ideal velocity distribution is hard to obtained and sometimes the non - physical solution, such as double covering of flow field or unclosed profiles, would come out. the proposed design procedure in the paper has avoided the disadvantage mentioned above. in this paper, a quasi - irrotational equation is used to describe the flow in cascade instead of the generally used irrotational equation

    眾所周知，一般的反問題和混合問題的最大特點，是在給定的壓力面和吸力面上的壓力分佈或速度分佈條件下，直接得到葉片的幾何形狀，它可以使葉型型面與表面氣流參數有機結起來；其不足之處在於，對設計者而言，很難給定理想的葉片表面壓力分佈或速度分佈，並且有時會得到一個非物理解，如：得出的初始葉型可能會出現前緣、尾緣不封閉的現象。
  3. We can get the unqualified light hydrocarbon back to fractional tower to resume fractionating which greatly insures the quality, we combine the science and technology tackle project from da qing natural gas company - the research on microcomputer detection and control system in light hydrocarbon blending crude oil, analyze the machining technology of production device in gas disposing station, study the physical and chemical character of impurity blending in the light hydrocarbon and establish the detection scheme finally

    並讓不合格的產品重新回到分餾塔中進行重新分餾加工，以確保產品質量。本文結合大慶天然氣公司的科技攻關項目? ?輕烴含原油微機測控系統研製，對一分公司油氣處理站的輕烴生產設備進行了生產工藝流程分析，同時也對輕烴和混入的原油雜質進行物理和化學性質的分析，確立了監控設計方案。
  4. The paper discusses dynamical conditions of the supercritical ore - forming fluid system based on study of regional geological background and analyses of physiochemical conditions of ore - forming process and puts forth the ore - forming mechanism : upper mantle uplift - mingling of meteoric water and magmatic hydrothermal fluid separated from acidic magma under tensile or transitional tensile environment - water / rock reaction - transportation - chemical coupling ore precipitation

    在分析超臨界成礦流體系統形成的區域地質背景和研究成礦物理化學條件的基礎上，探討了超臨界成礦流體系統形成的動力學條件，提出該系統的成礦機理：與燕山晚期酸性火山侵入巖漿有關的金銅礦床是在上地慢隆起、張性或向張性過渡背景下形成的，酸性巖漿經熔體流體分離作用形成的巖漿熱液與大氣降水混合，經水巖作用等復雜的輸運和化學反應耦合過程的動力學產物。
  5. The air absorbed by the fans is separated in and equably flows in the interior and outer canister, from to the heater and interior canister, the air is efficiently heat - treated, then the hot air influxes to and is balanced in because of the mixing by the heater, the hot airs temperature in has only little change, then it is separated completely from to ensure the balance - dryness of the colophony

    由鼓風機吸入的空氣在處被分散，于內筒和外筒間均勻地流動，從處進入內筒和加熱管進行有效地熱交換。然後熱風在處匯集，在處無序混亂的熱內被均化。由於加熱箱熱風混合效果的作風，處的熱風溫度變化幅度很小，熱風經熱風排出口被完全均勻地分散開，從而保證了樹脂均勻乾燥。
  6. 5. according to the requirement of amt start up experiment, using dynamic link library to program for different kinds of data acquisition card and transferring data between pc and multi scm. in this way data can be acquired successfully and engine throttle 、 clutch locking speed and eddycurrent dynamometer torque were controlled by pc programs

    根據試驗要求，採用動態鏈接庫的方法對不同數據採集卡進行混合編程，順利地採集參數和控制發動機節氣門開度及離合器結合速度，利用上下位機多機通信，使上位機控制電渦流測功機，實現了模擬加載。
  7. A man was turning the handle of the machine, and from its trough came the newly - cut swedes, the fresh smell of whose yellow chips was accompanied by the sounds of the snuffling wind, the smart swish of the slicing - blades, and the choppings of the hook in tess s leather - gloved hand

    有一個男工人搖動著機器的搖把，新切的蘿卜片就從機器的槽口裡不斷地流出來，那些黃色蘿卜片的新鮮氣味，同外面的呼呼風聲切蘿卜的刀片的嗖嗖聲和苔絲戴著皮手套清理蘿卜的聲音混合在一起。
  8. Mushy pvc ( dop + additives ) - beater ( stir well ) - vacuuming ( materiel has been completely dewatered and debubbled after vacuuming ) or mix with color paste which has been processed by ball mill and then dropped into mould cavity by needle cylinder ) - solidified in the constant temperature box ( color fixing ) - input basic material - sent to the constant temperature box in the flowing way and then forming and then forming and sent out automatically - cooled by fan - finished products

    糊狀pvc （增塑劑dop +助劑- - -打漿機攪拌均勻- - -抽真空處理） （真空機處理后的物料已完全脫離水分和氣泡）或球磨機處理后的色漿混合後用針筒滴入模具形腔- - -放入恆溫箱中固化（色彩定形） - - -注入底料- - -流水式送入恆溫機，定型后自動送出- - -風扇冷卻- - -成品
  9. The whole circuit ' s timing generation and synchronization was realized with cpld. as the channel of data transmitting, pof can isolate high voltage part and low voltage part efficiently. at the same time, a single chip processor was used to design a digital meter for the fiber current transducer

    系統採用cpld實現整個工作電路的時序發生和同步協調，利用光纖實現高壓部分和低壓部分的完全電氣隔離和實現信號傳輸，採用單片機技術實現混合式光纖電流互感器專用數字顯示儀表的設計。
  10. This dissertation focuses on how to develop a high performance damping mechanism based on multi - energy transitions, which is independent or little dependant with the viscoelasticity of polymer matrix. three sections are mainly included in this dissertation as follows : chlorinated polyethylene ( cpe ) / piezoelectric ceramic ( pzt ) / vapor grown carbon fiber ( vgcf ) composites ; cpe / 2, 2 ' - methylene - bis - ( 4 - methyl - 6 - cyclohexylphenol ) ( zkf ) / vgcf composites ; organic hybrids made from cpe and small molecules cpe / pzt / vgcf composites : the damping composites of multi - energy transitions mechanism were produced by mixing pzt and vgcf into cpe. in this system, the mechanical vibration energy that was transmitted to cpe was found to convert into joule ' s heat through conduction paths between vgcf in the polymer matrix, so the vibration fades away

    本論文主要包括三個方面的研究內容： ?氯化聚乙烯（ cpe ） /壓電陶瓷（ pzt ） /氣相生長碳纖維（ vgcf ）復合材料； ? cpe /雙[ （ 2 -羥基- 3 -環己基- 5 -甲基） -苯基]甲烷（ zkf ） / vgcf復合材料； ? cpe基有機小分子混雜型復合材料cpe / pzt / vgcf減振復合材料：利用壓電和導電填料填充高聚物基體，當復合材料受到機械振動時，通過高聚物基體將機械振動能傳遞到壓電陶瓷粒子上，利用壓電陶瓷的壓電效應，將機械能轉換成電能，則電流在導電粒子產生的迴路中流動，由於導電迴路具有一定的電阻，所以電能又轉變成熱能耗散掉，從而起到減振的目的。
  11. Thaw settlement cause negative friction. this paper base on the thought of " initiative cooling ", aim at three problems existing in common concrete pile used in frozen soil, a new type of pile is proposed to overcome the disadvantages of the classical pile used in frozen soil. pile body within active layer is fluted and refilled with porous materials such as gravels and ballasts, convection will be occur and then thermal exchange inside porous material in winter while only heat conduction exists in summer, as a result the soil around flutings will be cooled, so the top line of permafrost will be drive up

    本文基於「主動冷卻」地基的思想，以及針對凍土地區普通混凝土樁存在的三大問題，提出了一種新型樁的設計思路，運用數值模擬試驗手段對其冷卻機理與加固機理進行了系統研究，即在凍融活動層的深度范圍內，在混凝土樁身的表面刻槽，修築完時槽內填充碎石、塊石等多孔介質，通過外界大氣溫度的自然波動下多孔介質在冬季時存在的對流換熱機制，而在夏季只存在熱傳導，來達到主動冷卻樁周凍土和抬升凍土上限的目的。
  12. From physical principle, the electric property differences among oil, gas, and water are analyzed, and it is pointed that the electric properties of their mixture in oil wells are not only determined by their electric parameters, but also related to the mixture flow velocity, concentration and distribution state of each phase, and the measured electromagnetic field

    其次，從物理機理出發，對油、氣與水的介電特性和導電特性差異進行分析，指出油井內混合流體的電性質不僅與各相流體的電性參數有關，而且與流體的流動速度、各相含量、分佈狀態以及測量電磁場有關。
  13. Solid materials handling and pneumatic conveying system packaged machinery and its equipment and valves are mainly used for conveying, material unloading, dedusting, metering, mixing, packing units in the processing units of the solid materials including powder, particles, powder mixtures and flakes of abs, ps, pe, pp, pom, san, pet, pc, pta, pvc, bpa, sap, as and pmma in the trades of petroleum, chemical industries, chemical fiber, dye, pharmacy, food, electronic, paper making, natural gas, power, environmental protection, metallurgy and etc. it is applicable for various pneumatic conveying systems and gravity flow conveying systems under the conditions of diluted - phase, densed - phase, high pressure, low pressure and vacuum pressure

    固體物料處理和輸送系統成套機械及其專用設備、閥門主要應用於石油、化工、化纖、染料、醫藥、食品、電子、造紙、天然氣、電力、環保、冶金等領域中固體物料（含abs 、 ps 、 pe 、 pp 、 pom 、 san 、 pet 、 pc 、 pta 、 pvc 、 bpa 、 sap等粉沫、顆粒物料、粉粒混合物、片狀）生產加工過程中輸送、卸料、除塵、計量、混合、包裝等工段使用，能適用於稀相、密相、高壓、低壓、負壓各種氣力輸送系統和重力流輸送系統。
  14. The advantages of hcci are numerous comparing with the traditional engine. relative to si gasoline engines, hcci engines are more efficient, because they have no elimination of throttling losses, use the high compression ratios and have shorter combustion duration. relative to cidi engines, hcci engines have extraordinarily lower emissions of pm and nox and can offer more power as high as cidi engines with the dilute homogeneous air and fuel mixture

    與傳統的發動機相比均質壓燃（ hcci ）具有很多優勢:與火花點火汽油機相比， hcci發動機由於沒有節流損失，壓縮比較高，燃燒持續期短，其效率更高;與直噴柴油機相比， hcci發動機的碳煙和氮氧化物排放非常低，並且稀薄空燃混合氣可以產生與柴油機一樣高的功率。
  15. Referred and analyzed the developing and researching achievement of high turbulent combustion chamber on diesel engine in the world, the grooved combustion chamber is designed and developed based on the rationale of designing high turbulent combustion chamber and employed the effect of the grooved of the combustion chamber wall on the spray impingement

    在分析和參考國內外柴油機高紊流燃燒系統開發研究成果的基礎上，根據高紊流燃燒室設計的理論基礎，利用矩形環槽對燃油噴霧撞壁效應能加速混合氣形成的機理，設計開發了在燃燒室側壁上加工有矩形環槽的燃燒室方案。
  16. The numerical simulation of the motor cold flow field and the mixing process of various kinds of gases are performed by piso algorithm

    採用piso演算法模擬了冷流狀態下發動機的內流場和各種氣體組分的相互摻混過程。
  17. When dicussing reliability design and reliahbaiiy ensuring methods, a new reliability calculating model of petroleum logging tools is presented, reliability assurimg technologies should be taken in petroleum logging tools and their using approaches are presented and stated from electricity design and mechanical design, reliability system model of petroleum logging tool is set up according to the latest reliability theory, reliability indexes of petroleum logging tool and their acquiring ways are discussed, the reconmended reliability indexes ( mwture, nolwnm, mtbf, mttf ) of petroleum logging tool are presented : the mean working time under rated error ( mwture ) of the new tool is obtained through experiments. when studying data processing methods, the property of gamma - ray signal is stated and the type of it ' s measuring error is examined using statistical method, the basic theory of digital filtering and the basic situation of digital filtering methods are introduced and analyzed, the factors affecting digital filtering effect to gamma - ray signal and the effect of digital filtering to logging curve are analyzed, the evaluting criteria ( rvi, rmse, sfi ) of digital filtering effect are set up from two aspects, named as real value acquiring of steady section and the formation boundary checking and processing, the related filtering methods and examining methods are given out. the design methods of digital filter used to process gamma - ray signal are discussed, the mixed filtering scheme of natural gamma - ray log is presented, the realization ways are discussed. the selective filtering system and it ' s realization flow are given out through quantitive reseaching to part of digital filters, three new filtering sheme will be used to process gamma - ray signal in era2000 logging system

    在探討可靠性設計與可靠性保障技術時，提出了石油測井儀器的可靠性計算新模型，從電氣和機械兩個方面，提出並闡述了應採用的可靠性保障技術及其使用方法：根據最新可靠性理論，建立了石油測井儀器的可靠性系統模型，探討了石油測井儀器的可靠性指標及其獲取途徑，提出了推薦使用的石油測井儀器可靠性指標（ mwture ， nolwnm ， mtbf ， mttf ） ；通過試驗，得到了所設計儀器的穩定工作時間（ mwture ） 。在研究數據處理方法時，闡述了伽瑪信號的特徵，對測量誤差類型進行了統計檢驗；介紹了數字濾波的基本理論、數字濾波方法的概況，並進行了分析；對伽瑪信號數字濾波效果的影響因素及其對測井曲線的影響進行了基本分析；從獲取平穩段真值、地層邊界的檢測與處理兩個方面，建立了數字濾波效果的評價準則（ rvi ， rmse ， sfi ） ，給出了相應的數字濾波方法及效果評價方法；探討了自然伽瑪信號數字濾波器的設計方法，提出了適合自然伽瑪測井的混合濾波方案，探討了混合濾波方案的實現途徑；通過對部分數字濾波方法的定量研究，給出了靈活可選的數字濾波系統構成及實現流程；提出的三種濾波方案，將用於era2000成像測井系統，對自然伽瑪測井數據進行濾波處理。
  18. Then mathematical relationship between the flows of mixture and the throat area, shrinking degree of mixer ( mathematical model ) can be established to meet the aim of the highest power of engine

    以滿足發動機最大功率為設計目標，建立起混合氣的流量與混合器的入口角度和喉口面積之間的數學關系，即數學模型。
  19. With computations and analysis, the comprehension on the mixing and combustion process is increased, and some significative results are listed below : a ) there are three recirculation regions and one vortex region in the combustor, and these recirculation regions affect the combustion process deeply, b ) increasing side - arm angle and moving side - air inlet position toward the fuel inlet can improve mixing and combustion characteristics, and increase the combustion efficiency, c ) when the angle between two air - inlets equals to 180

    通過計算與分析，增進了對補燃室內摻混燃燒過程的理解，為固體火箭沖壓發動機補燃室設計提供了一些有意義的結果： 1補燃室內的流動十分復雜，存在三個迴流區和一個旋渦區，迴流區對摻混燃燒過程有重要影響； 2增大空氣入射角度、向前移動進氣道出口位置有利於增強頭部迴流區強度，增強摻混效果，燃燒效率上升； 3
  20. It is shown that when the exit area of secondary nozzle and the fuel / oxidizer ratio is fixed, the increase of mass flow rate of secondary flow lead to the decrease of velocity of mixed flow, and increase of total mass flow rate. the synthetical result of these two phenomenon cause the increase of thrust of rocket ejector, but the increasing magnitude is relatively small, indicating that these is no necessary to claim large bypass ratio in rocket ejector design. in the comparison between two configurations, the typical one has better performance, indicating the importance of pressure ratio

    結果表明：在固定二次噴管出口面積和氧燃比的條件下，二次流（引射空氣流）流量的增加引起混合氣體出口速度的下降和總流量的增加，二者綜合作用使發動機推力增加，但增幅不大，表明在設計發動機結構和工作參數時，不必過分追求大的引射系數；兩種結構的性能對比分析表明了增壓比對引射火箭性能的提高具有重要意義；對引射火箭的熱力循環分析同樣表明，增壓比對于提高發動機性能非常關鍵。
分享友人
分享到 Line

分享到臉書