氣路 的英文怎麼說

中文拼音 [qìlù]
氣路 英文
air course
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
  1. By comparing the dry plate pressures drop and distributions of velocities simulated on single valve with those of double valves, it was found that there was intense turbulence in the flow fields around fixed - valve, there were eddy areas between valve side orifices and tray wall, there were eddies above the valves too, these led to the complex behaviors of gas perforating valve, these had a great effect on the gas - liquid mass transfer process. at the same time, in order to prevent the disadvantageous effect of gas between one valve with another on the gas - liquid mass transfer, it was very effective to change the fields of gas perforating valve by folding the edges of valve

    通過對數值模擬得出的單閥和雙閥塔板的干板壓降及流場速度分佈分析對比后發現，固定閥周圍流場存在較強的湍動，閥側孔與塔板壁面區域以及閥體的上方空間存在明顯的渦流區，使氣體穿閥后的行為變得復雜，並對氣液傳質過程產生重大影響；模擬結果表明，為防止和削弱固定閥間的對沖造成的「死區」對傳質帶來的不利影響，通過折邊來改變氣體的氣路是非常有效的，模擬值與實驗值基本得到吻合。
  2. Now with the development of computer control technique applied in it, computer control technique has had a profound influence on pneumatic system structure / control performance / control theory etc. this thesis deeply researches on the task - computer control smart high - speed pneumatic cushioning system. which mainly includes the design of mechanical structure / electronical circuit / pneumatic loop and the researches of system modeling / simulation / control strategy

    計算機控制技術和電-氣比例伺服控制技術的結合，更是對控制系統的性能、系統的結構以及控制理論等多方面都產生了極為深刻的影響。本文對計算機控制智能高速氣動緩沖系統進行了機械、電氣、氣路系統的設計以及系統建模方法、系統辨識研究和控制策略研究。
  3. The small part which returns via an air path is called the leakage flu and is indicated by dotted lines.

    一小部分經空氣路徑返回的磁通量，叫做漏磁通量，並用虛線畫出。
  4. There are no branches defined in the zone air path constructs

    在空調區域的空氣路徑下不再社分支。
  5. The air paths consist of a group of components ? zone splitters and zone supply plenums for the supply path and zone return plenums and zone mixers for the return path

    空氣路徑包含以下幾部分：送風路徑的空調區域分離器、送風靜壓箱以及回風路徑的回風靜壓箱和混風器。
  6. If the protective seal is not air proof or poor gas purity, it will also bring welding quality problems

    氣路有密封不好的問題，或氣體純度不高，也會引起焊接質量問題。
  7. This paper analyses the usage of lgk series of air plasma arc cutting machine, and enumerates the causes and solutions of striking arc, main circuit, gas path and cutting torch breakdown

    摘要分析了lgk系列空氣等離子弧切割機的使用方法，例舉了其引弧故障、主電路故障、氣路故障、割槍故障產生的原因和解決方法。
  8. In this paper, basic pneumatic - measuring theory and air circuit system working principle are introduced. the pneumatic - electric transducer employs a mpx5500dp silicon pressure sensor which converts air pressure signal into voltage signal, and displays on the electron column after the signal conditional circuit ’ s processing

    本課題從分析氣動測量的基礎理論入手，研究氣路系統的工作原理，用mpx5500dp擴散硅壓力傳感器將氣體壓力信號轉換為電壓信號，進而研製成功一種氣電轉換器。
  9. Different equations to corresponding components are presented by analysing and transformating the general equations of fluid routes, then static characteristics mathematical model of liquid propellant space propulsion system is presented. based on the data of static characteristics calculation, mass model of thruster, propellant, propellant tank, gas, gas bottle, pipe and valve is presented using both the method of statistical regression and the method of stress analysis, then corresponding mass model is presented. based on the characteristics of liquid propellant space propulsion systems, analyse the five phases ( concept and definition, design and improvement, manufactureing and arrangement, operation and ma intenance, disposal ) in which life cycle cost of liquid propellant space propulsion systems is cost separately, then discompsed structure of life cycle cost and model of life cycle cost are presented

    將組件分成氣路組件和液路組件，再對氣路組件和液路組件進行相應的分類，然後通過對通用流路方程進行分析和變換對不同類型的組件分別建立不同的方程，從而建立了一個適用於液體推進劑空間推進系統的靜態數學模型；根據靜態計算所得到的數據，應用統計回歸法和應力分析法分別建立推力室、推進劑、推進劑貯箱、氣體、氣瓶以及導管和活門等的質量模型，從而建立相應的質量模型；結合液體推進劑空間推進系統特點，對液體推進劑空間推進系統全壽命周期費用發生的五個階段（概念和定義、設計和改進、製造和安裝、運行和維修、處理）分別進行分析，建立了液體推進劑空間推進系統全壽命周期費用分解結構和全壽命周期費用模型。
  10. Second, on account of the block of gas channel we designed a gas channel system, through which the hydrogen can flush the gas channel after the reaction by the control of valves

    針對以前氣路堵塞的問題設計並製作了氣路系統，使氫氣在反應后能夠通過閥門控制對氣路進行沖洗。
  11. K - 006 series of blowing thermocouple are applicable to measure temperature in gas making furnace of chemical fertilizer which principle is a gas way come into being between sheathed thermocouple and outer protective tube

    一概述wrk - 006系列吹氣熱電偶產品適用於測量化肥造氣爐溫度，原理是在鎧裝熱電偶和外保護套管之間構成一定的氣路，在
  12. Duddell street steps gas lamps duddell street, central

    都爹利街石階及煤氣路燈
  13. It has the advanced radial technology and the movement path likes 11 pieces plum blossoms shape, this machine uses a head screw pole to go up and down to control the power head, it has the enlarged bench, and air current double - direction adjusting valve to controlled the riveting speed effectively. the electricity system added the counter to count the work piece which was be processed, he time relay control the riveting times

    Jm3tq - d是汽動類小型徑向鉚接機，與jm3tq - b和jm3tq - c相比，提高最大工作行程到40mm ，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機採用頭部絲桿升降粗調，加大了工作臺面，氣路加裝雙向調節閥，有效控制鉚接速度。
  14. The paper focused on this task and covered these contents : realizing the real - time, online and dynamic simulation of the pneumatic operation system for marine main engine on the basis of analyzing the pneumatic devices " principle and by the means of multimedia technology ; describing dynamically the flowing direction of the controlling pneumatic line according to its logical relations in the three working conditions - starting, stopping and reversing

    本文圍繞此課題主要完成以下內容：在對manb & w主機氣動裝置原理分析基礎上，運用計算機多媒體技術，實現船舶主機氣動控制系統的實時、在線、動態模擬。針對主機的起動、停車、換向三種操作工況，依據氣路邏輯關系動態地描述了控制氣路的流向。
  15. Presents the application of fault prediction technique and the way of predicting its numerical values, the algorithm given for the neural network model in the prediction process, and illustrates with the gas pipeline of a space propulsion system as an example the realization of fault prediction by combining the neural network and the fault prediction technique with the diagnosis expert system to form a fault prediction system

    探討了故障預報技術的應用及其數值預測方法，給出了神經網路模型在預測過程中的演算法.把神經網路、預測技術和診斷專家系統相結合建立了一個故障預報系統；以空間推進系統氣路部分的故障為例，實現了故障的預測
  16. The gun structure mainly considered the designs of waterway and gas way and the fixed and regulated style of electrode, it ' s main content was to determined the technical measure and inexpensive geometric figure of strengthen conductivity

    槍體結構主要考慮水路和氣路的設計及電極的固定和調節方式，主要內容是確定增強傳熱的技術措施及相應的幾何形狀。
  17. The double air regulator control riveting speed effectively

    氣路加裝雙向調節閥，有效控制鉚頭上下速度。
  18. Axis coaxial, and available fixes a position in the clamping apparatus

    氣路加裝雙向調節閥，有效控制鉚接速度。
  19. The double air regulator to control riveting speed effectively

    氣路加裝雙向調節閥，有效控制鉚接速度和回程速度。
  20. Energy - saving design, welding stop, gas circuit and electric circuit automatically close

    節能設計，焊接停止，氣路、電路自動關閉。
分享友人
分享到 Line

分享到臉書