氣體粘度計量 的英文怎麼說

中文拼音 [qìtǐniándùjìliáng]
氣體粘度計量 英文
gas viscosity measurement
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 體 : 體構詞成分。
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 氣體 : gas; gaseous fluid
  • 計量 : calculate; estimate; meterage; metering; batching; measure
  1. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  2. Moreover, the resulted prediction model of foam size of the closed cell aluminum foam was verified by comparison to the experimental results from the foaming process at different foaming conditions, and the predicted bubble diameter is in good agreement with the experimental ones, the relative error distributes between - 5. 04 % and 6. 32 %

    當入射空氣的壓強、氣流量，液面高度，出氣孔直徑增大時，氣泡直徑隨之增大；當出氣孔數量，液體粘度增大時，氣泡直徑減小，表面張力對氣泡直徑的影響可以忽略不計；靜態條件下液體表面氣泡直徑的預測值和實驗測量值符合得較好，相對誤差分佈在- 5 . 04 % ~ 6 . 32 %之間。
  3. The temperature pressure measuring instruments of the standard programme can be used anywhere where liquid or gaseous materials to be measured do not attack copper alloys, do not crystallise and are not highly viscous

    溫度壓力計標準程序的溫度-壓力測量儀可以用於任何液體氣體介質測量，但介質不能腐蝕銅合金結晶或高粘稠。
分享友人
分享到 Line

分享到臉書