水下電弧焊接 的英文怎麼說
中文拼音 [shuǐxiàdiànhúhànjiē]
水下電弧焊接
英文
underwater arc welding- 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
- 下 : 下動詞1. （用在動詞后,表示由高處到低處） 2. （用在動詞后, 表示有空間, 能容納） 3. （用在動詞后, 表示動作的完成或結果）
- 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
- 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
- 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
- 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
- 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
-
Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定Abstract : the image of arc zone of flux - cored underwater wet welding was developed with underwater ccd camera system and composed filter technology. the discussion is mainly focused on the theory of edge detection. an image edge detection method based on median filter and grads algorithm was developed to detect the arc burning zone and arc bubble zone efficiently, which laid the foundation for further analysis of underwater wet welding arc mechanism and process control
文摘:通過復合濾光技術和水下ccd攝像系統，採集出了藥芯焊絲水下濕法焊接電弧區域圖像，重點論述了邊緣檢測理論，確定了基於中值濾波和梯度運算元的電弧區域圖像邊緣檢測方法，有效地區分了電弧燃燒區域和電弧氣泡區域，從而為水下濕法焊接電弧的機理分析及水下焊接過程式控制制奠定了基礎。
分享友人