水冷活塞 的英文怎麼說

中文拼音 [shuǐlěnghuósè]
水冷活塞 英文
water cooled piston
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 活 : Ⅰ動詞1 （生存; 有生命） live 2 [書面語]（救活） save （the life of a person）:活人無算 （of a goo...
  • 活塞 : plunger; stop; bibb cock; bib（b）; [機械工程] piston; gas piston; headed piston活塞桿 piston rod...
  1. In the event that a boiler does shut down the stop - check must prevent backflow into the boiler, the weight of the disc and dash pot piston, through the force of gravity, promote rapid sealing so steam and condensate cannot backflow into the boiler even at low pressures

    如果鍋爐沒有關閉截止止回閥，則必須防止迴流到鍋爐上，閥瓣壓鐵和緩沖活塞，在重力的作用下，能夠迅速實現密封，使得蒸汽和冷凝水即使在低壓下也不會迴流到鍋爐里。
  2. When the stopcock is opened, water flows from the top of the warmer column into the colder column.

    打開活塞后，水即由較熱的水柱頂端流入較冷的水柱。
  3. In chapter 4, for the first time, in the way of virtual malfunction simulation, cooling water of diesel engine type 4135 has been simulated under the stopping water supply malfunction. and the analysis and discussion has been taken on the result of transient temperature curve of the simulation. and in the same way, internally cooling oil piston of diesel engine type 180 has been numerically simulated on the virtual thermal loading mal

    得出了虛擬其斷水故障模擬的瞬態溫度曲線結果，並對其進行了分析和探討；同時也用虛擬模擬的思想對180型柴油機內油冷活塞進行了虛擬其熱負荷故障的數值模擬，得出了其在斷油情況下和超負荷運轉情況下的分析結果。
  4. For the first time, it puts forward a conception of. thermal dynamic simulation and sets up a supposed analytical theory for scuffing failure and cylinder scoring of piston assembly and cylinder liner. that is followed with the simulation of scuffing failure and cylinder scoring of internal combustion engine under the condition of stopping cooling water supply and over loading

    首次提出了熱動態模擬的概念，第一次大膽假設了活塞組、缸套擦傷、拉缸時的分析理論，模擬出了在中斷冷卻水和超負荷狀態下柴油機的擦傷、拉缸。
  5. To solve the heat transfer boundary problem among the piston, liner, coolant and body parts, especially the temperature and heat transfer among the coolant, liner and body

    摘要為解決發動機活塞組缸套冷卻水機體之間傳熱邊界條件難以確定的問題，尤其是冷卻水和缸套、機體之間的流固邊界的溫度和換熱系數，將這幾個部件作為一個耦合系統進行傳熱研究。
  6. Comparison between simulation and measurement temperature data shows that simulation results are in good agreement with experimental data and the fluid - solid coupled method can solve the steady heat transfer among piston, liner, coolant and body of diesel engines

    和實驗測量值的對比結果表明：模擬結果與實測數據吻合較好，用流固耦合方法模擬柴油機活塞組缸套冷卻水機體之間的穩態傳熱是可行的。
  7. For dirty water or sanitary sewage applications, clogging of the cooling jacket passages can easily occur due to a build - up of solids, grease, corrosion and other matter

    但是對于污水或生活污水應用領域，冷卻套通道由於淤積固體顆粒、油脂、腐蝕等等卻極易發生堵塞。
  8. Piston cooling water pump

    活塞冷卻水泵
分享友人
分享到 Line

分享到臉書